10” COMPOUND MITER SAW
Model 91995
SET UP AND OPERATINg INSTRUCTIONS
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
Distributed exclusively by Harbor Freight Tools®.
3491 Mission Oaks Blvd., Camarillo, CA 93011
Read this material before using this product.
Failure to do so can result in serious injury.
SAVE THIS MANUAl.
Copyright© 2004 by Harbor Freight Tools®. All rights reserved. No portion of this
manual or any artwork contained herein may be reproduced in any shape or form
without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Revised 07k
Download from Www.Somanuals.com. All Manuals Search And Download.
SPECIFICATIONS
Electrical Requirements
120 V / 60 Hz / 1800 Input Watts.
15.0 AMPs Start Up / 5300 RPM No Load.
Three Prong, Grounded, Power Cord Plug.
Power Switch Type: Squeeze Type.
E105017
Saw Blade (Included) Diameter/Type 10” Diameter / 60 Teeth.
7,000 Maximum RPM.
Arbor Size
5/8” Diameter.
Crosscut Capacity
4-11/16” x 2-15/16” @ 90°.
4-11/16” x 1-9/16” @ 45°.
Blade Tilt Capacity
Positive Stops
Overall Table Size
Accessories Included
0° - 45° Left and Right.
0°, 15°, 22.5°, 30°, 45° Left and Right.
18-1/8” W x 5-3/8” L x 3-1/8” H.
Dust Bag / Extension Holders (Qty. 2).
UNPACKINg
When unpacking, check to make sure all the parts shown on the Parts list on
page 23 are included. If any parts are missing or broken, please call Harbor Freight
Tools at the number shown on the cover of this manual as soon as possible.
SAVE THIS MANUAl
You will need this manual for the safety warnings and precautions, assembly,
operating, inspection, maintenance and cleaning procedures, parts list and assembly
diagram. Keep your invoice with this manual. Write the invoice number on the inside of the
front cover. Keep this manual and invoice in a safe and dry place for future reference.
gENERAl SAFETY RUlES
WARNINg! Read all instructions
Failure to follow all instructions listed below may result in electric shock,
fire, and/or serious injury. The term “power tool” in all of the warnings listed
below refers to your line-operated (corded) power tool or battery-operated
(cordless) power tool.
SAVE THESE INSTRUCTIONS
WORK AREA
1.
2.
Keep your work area clean and well lit. Cluttered benches and dark areas
invite accidents.
Do not operate power tools in explosive atmospheres, such as in the
presence of flammable liquids, gases, or dust. Power tools create sparks
which may ignite flammables.
Rev 07k
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
1.
Keep bystanders, children, and visitors away while operating a power tool.
Distractions can cause you to lose control. Protect others in the work area from
debris such as chips and sparks. Provide barriers or shields as needed.
ElECTRICAl SAFETY
grounded tools must be plugged into an outlet properly installed and
grounded in accordance with all codes and ordinances. Never remove the
grounding prong or modify the plug in any way. Do not use any adapter
plugs. Check with a qualified electrician if you are in doubt as to whether
the outlet is properly grounded. If the tools should electrically malfunction or
break down, grounding provides a low resistance path to carry electricity away
from the user.
2.
3.
Double insulated tools are equipped with a polarized plug (one blade is
wider than the other). This plug will fit in a polarized outlet only one way.
If the plug does not fit fully in the outlet, reverse the plug. If it still does
not fit, contact a qualified electrician to install a polarized outlet. Do not
change the plug in any way. Double insulation
eliminates the need for the
three wire grounded power cord and grounded power supply system.
Avoid body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerators. There is an increased risk of electric shock if your
body is grounded.
4.
5.
Do not expose power tools to rain or wet conditions. Water entering a power
tool will increase the risk of electric shock.
Do not abuse the Power Cord. Never use Power Cord to carry the tools or
pull Plug from an outlet. Keep the Power Cord away from heat, oil, sharp
edges, or moving parts. Replace damaged Power Cords immediately.
Damaged Power Cords increase the risk of electric shock.
ꢀ.
When operating a power tool outside, use an outdoor extension cord
marked “W-A” or “W”. These extension cords are rated for outdoor use, and
reduce the risk of electric shock.
PERSONAl SAFETY
1.
2.
Stay alert. Watch what you are doing, and use common sense when
operating a power tool. Do not use a power tool while tired or under the
influence of drugs, alcohol, or medication. A moment of inattention while
operating power tools may result in serious personal injury.
Dress properly. Do not wear loose clothing or jewelry. Contain long
hair. Keep your hair, clothing, and gloves away from moving parts. Loose
clothes, jewelry, or long hair can be caught in moving parts.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
5.
ꢀ.
Avoid accidental starting. Be sure the Power Switch is off before plugging
in. Carrying power tools with your finger on the Power Switch, or plugging in
power tools with the Power Switch on, invites accidents.
Remove adjusting keys or wrenches before turning the power tool on. A
wrench or a key that is left attached to a rotating part of the power tool may result
in personal injury.
Do not overreach. Keep proper footing and balance at all times. Proper
footing and balance enables better control of the power tool in unexpected
situations.
Use safety equipment. Always wear ANSI approved safety glasses
underneath a full face shield, a dust mask or respirator, and hearing
protection.
TOOl USE AND CARE
1.
Use clamps or other practical ways to secure and support the workpiece to
a stable platform. Holding the work by hand is unstable and may lead to loss of
control. Only work on a workpiece that is properly secured.
2.
3.
Do not force the tool. Use the correct tool for your application. The correct
tool will do the job better and safer at the rate for which it is designed.
Do not use the power tool if the Power Switch does not turn it on or off.
Any tool that cannot be controlled with the Power Switch is dangerous and must
be replaced.
4.
Disconnect the Power Cord Plug from the power source before making any
adjustments, changing accessories, or storing the tool. Such preventive
safety measures reduce the risk of starting the tool accidentally.
5.
ꢀ.
ꢁ.
Store idle tools out of reach of children and other untrained persons. Tools
are dangerous in the hands of untrained users.
Maintain tools with care. Do not use a damaged tool. Tag damaged tools “Do
not use” until repaired.
Check for misalignment or binding of moving parts, breakage of parts,
cracking or breakage of the Saw Blade, and any other condition that may
affect the tool’s operation. If damaged, have the tool serviced before using.
Many accidents are caused by poorly maintained tools.
ꢂ.
Use only accessories that are recommended by the manufacturer for your
model. Accessories that may be suitable for one tool may become hazardous
when used on another tool.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
SERVICE
1.
2.
Tool service must be performed only by qualified repair personnel. Service
or maintenance performed by unqualified personnel could result in a risk of injury.
When servicing a tool, use only identical replacement parts. Follow
instructions in the “Inspection, Maintenance, And Cleaning” section of this
manual. Use of unauthorized parts or failure to follow maintenance instructions
may create a risk of electric shock or injury.
SPECIFIC SAFETY RUlES
1.
2.
Maintain a safe working environment. Keep the work area well lit. Make sure
there is adequate surrounding workspace. Always keep the work area free of
obstructions, grease, oil, trash, and other debris. Do not use the Miter Saw in
areas near flammable chemicals, dusts, and vapors. Do not use this product in a
damp or wet location.
Maintain labels and nameplates on the Miter Saw. These carry important
information. If unreadable or missing, contact Harbor Freight Tools for a
replacement.
3.
4.
Do not force the equipment. This Miter Saw will do the work better and safer at
the speed and capacity for which it was designed.
Keep all guards in place and in working order. Never remove or disable
guards.
5.
ꢀ.
Remove all adjusting wrenches from the Miter Saw before turning it on.
Do not abuse the Power Cord. Do not use the Power Cord to pull its Plug from
an electrical outlet. Keep the Power Cord away from heat, oil, sharp edges, and
moving parts. Route the Power Cord safely. Protect the Power Cord from being
damaged by other equipment in the work area. Do not route the Power Cord
where it can be walked on or tripped over. Replace a damaged Power Cord
immediately.
ꢁ.
ꢂ.
Do not use this Miter Saw for cutting metals or brittle materials. Do not cut
dangerous materials, such as asbestos which can cause harmful dust or vapors.
When replacing the Saw Blade, make sure the new Saw Blade has a
diameter of 10”, an RPM rating of at least 7000, and has an arbor hole of
5/8” diameter.
9.
To avoid accidental injury, always wear heavy duty work gloves when
changing a Saw Blade.
Rev 07k
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 5
Download from Www.Somanuals.com. All Manuals Search And Download.
10.
Before using the Miter Saw, make sure the Saw Blade is properly mounted
on the Saw Spindle. Make sure the Saw Blade is balanced, and is not cracked
or bent.
11.
12.
13.
14.
The Saw Blade will become hot while cutting. Allow the Saw Blade to
completely cool before touching.
Make sure the workpiece is free from nails and any other foreign objects
which can damage the Saw Blade.
Keep your body positioned to either side of the Saw Blade, but not in line
with the Saw Blade. “Kickback” can cause the Saw to jump backwards.
Causes and operator prevention of “kickback”: Kickback is a sudden
reaction to a pinched, bound, or misaligned Saw Blade, causing an uncontrolled
Saw to lift up and out of the workpiece toward the operator. When the Saw Blade
is pinched or bound tightly by the kerf closing down, the Saw Blade stalls and
the Motor reaction drives the tool rapidly toward the operator. If the Saw Blade
becomes twisted or misaligned in the cut, the teeth at the back edge of the Saw
Blade can dig into the top surface of the workpiece, causing the Saw Blade to
climb out of the kerf and jump toward the operator. Kickback is a result of tool
misuse and/or incorrect operating procedures or conditions and can be
minimized by taking proper precautions as given below:
a. Maintain a firm grip with both hands on the Saw, and position your body
and arm to allow you to resist kickback forces.
b. When the Saw Blade is binding, or when interrupting a cut for any
reason, release the Power Switch and hold the Saw motionless in the
workpiece until the Saw Blade comes to a complete stop. Never attempt
to remove the Saw Blade from the workpiece or pull the Saw backward while
the Saw Blade is in motion or kickback can occur.
c. When restarting the Saw in the workpiece, center the Saw Blade in the
kerf and check that the saw teeth are not engaged into the workpiece. If
the Saw Blade is binding, it may walk up or kickback from the workpiece as
the Saw is restarted.
d. Support large panels to minimize the risk of Saw Blade pinching and
kickback. Large panels tend to sag under their own weight. Supports must
be placed under the panel on both sides, near the line of cut and near the
edge of the panel.
e. Do not use a dull or damaged Saw Blade. Unsharpened or improperly set
Saw Blades produce a narrow kerf causing excessive friction, Saw Blade
binding and kickback.
f. Make sure all Saw adjustments are tight and secure before making a cut.
If Saw adjustments shift while cutting, it may cause binding and kickback.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
15.
The Cross Pin (28) should always be in the “locked down” position when
the Saw is not being used and when the Saw is being transported. The
Cross Pin should be activated in the “locked up” position when changing
Saw Blades. NEVER use the Cross Pin in any cutting operation. The Cross
Pin allows the operator to lock the Saw Blade in position, preventing the Saw
Blade from being raised or lowered.
1ꢀ.
1ꢁ.
Allow the Saw Blade to spin up to full speed before feeding it into the
workpiece. Do not force the Saw Blade into the workpiece when cutting. Apply
moderate pressure, allowing the Saw Blade to cut without being forced. When
turning off the Saw, allow the Saw Blade to spin down and stop on its own. Do
not press against the Saw Blade to stop it.
Turn off the Saw and allow the Saw Blade to stop on its own if the Saw
Blade is to be backed out of an uncompleted cut.
1ꢂ.
19.
Industrial applications must follow OSHA requirements.
Proper Miter Saw location: Make sure the Miter Saw is located on a flat, level,
sturdy surface capable of supporting the weight of the Miter Saw, workpieces,
and all other tools and accessories.
20.
Do not abuse the Power Cord. Do not use the Power Cord to pull the Power
Plug from an electrical outlet. Keep the Power Cord away from heat, oil, sharp
edges, and moving parts. Route the Power Cord safely. Do not route the Power
Cord where it can be walked on or tripped over. Replace a damaged Power Cord
immediately.
21.
22.
23.
Keep all safety guards in place, in proper adjustment, and in proper
alignment.
Never attempt to remove material stuck in the moving parts of the Miter
Saw while the machine is plugged in and running.
Whenever possible, use clamps or other safe, practical ways to hold and
support the workpiece. Do not attempt to cut material that does not have a flat
surface, unless a suitable support is used.
24.
25.
Always keep hands and fingers away from the spinning Saw Blade.
Use eye, hearing, and breathing protection. Always wear ANSI-approved
safety impact eye goggles, hearing protectors, and dust masks or respirator
when working with the Miter Saw.
2ꢀ.
Do not use this product if under the influence of alcohol or drugs. Read
warning labels on prescriptions to determine if your judgement or reflexes are
impaired while taking drugs. If there is any doubt, do not attempt to use this
product.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
2ꢁ.
2ꢂ.
Maintain this product with care. Keep the Miter Saw clean and dry for better
and safer performance. For your safety, service and maintenance should be
performed regularly by a qualified technician.
Use the right tool or attachment for the right job. Do not attempt to force a
small tool or attachment to do the work of a larger industrial tool or attachment.
There are certain applications for which this product was designed. It will do the
job better and more safely at the rate for which it was intended. Do not modify
this product, and do not use this product for a purpose for which it was not
intended.
29.
Always turn off the Miter Saw and unplug the Power Cord (102) from its
electrical outlet before changing accessories or performing inspection,
maintenance, or cleaning procedures.
30.
31.
Keep children out of the work area. Never allow children to play with tools.
Always lock and secure the work area.
People with pacemakers should consult their physician(s) before use.
Electromagnetic fields in close proximity to heart pacemaker could cause
pacemaker interference or pacemaker failure.
32.
WARNINg! Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities, contain chemicals known (to the State of California)
to cause cancer, birth defects or other reproductive harm. Some examples of
these chemicals are: lead from lead-based paints, crystalline silica from bricks
and cement or other masonry products, arsenic and chromium from
chemically treated lumber. Your risk from these exposures varies, depending on
how often you do this type of work. To reduce your exposure to these chemicals:
work in a well ventilated area, and work with approved safety equipment, such as
those dust masks that are specially designed to filter out microscopic particles.
(California Health & Safety Code 25249.5, et seq.)
33.
The warnings, precautions, and instructions discussed in this manual cannot
cover all possible conditions and situations that may occur. The operator must
understand that common sense and caution are factors which cannot be built into
this product, but must be supplied by the operator.
SAVE THESE INSTRUCTIONS
SKU 91995
For technical questions, please call 1-800-444-3353.
Page ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
gROUNDINg
Improperly connecting the grounding wire can result in
electric shock.
WARNINg
Check with a qualified electrician if you are in doubt as to
whether the outlet is properly grounded. Do not modify
the power cord plug provided with the tool. Never remove
the grounding prong from the plug. Do not use the tool if
the power cord or plug is damaged. If damaged, have it
repaired by a service facility before use. If the plug will not
fit the outlet, have a proper outlet installed by a qualified
electrician.
grounded Tools: Tools with Three Prong Plugs
1.
Tools marked with “Grounding Required” have a three wire cord and three prong
grounding plug. The plug must be connected to
a properly grounded outlet. If the tool should
electrically malfunction or break down, grounding
provides a low resistance path to carry electricity
away from the user, reducing the risk of electric
shock. (See 3-Prong Plug and Outlet.)
2.
3.
The grounding prong in the plug is connected
through the green wire inside the cord to the
grounding system in the tool. The green wire
in the cord must be the only wire connected to
the tool’s grounding system and must never be attached to an electrically “live”
terminal. (See 3-Prong Plug and Outlet.)
3-Prong Plug and Outlet
The tool must be plugged into an appropriate outlet, properly installed and
grounded in accordance with all codes and ordinances. The plug and outlet
should look like those in the following illustration.
(See 3-Prong Plug and Outlet.)
Extension Cords
1.
2.
Grounded tools require a three wire extension cord. Double Insulated tools can
use either a two or three wire extension cord.
As the distance from the supply outlet increases, you must use a heavier gauge
extension cord. Using extension cords with inadequately sized wire causes a
serious drop in voltage, resulting in loss of power and possible tool damage.
(See Table A.)
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
The smaller the gauge number of the wire, the greater the capacity of the cord.
For example, a 14 gauge cord can carry a higher current than a 1ꢀ gauge cord.
(See Table A.)
4.
5.
When using more than one extension cord to make up the total length, make
sure each cord contains at least the minimum wire size required. (See Table A.)
If you are using one extension cord for more than one tool, add the nameplate
amperes and use the sum to determine the required minimum cord size.
(See Table A.)
ꢀ.
ꢁ.
If you are using an extension cord outdoors, make sure it is marked with the
suffix “W-A” (“W” in Canada) to indicate it is acceptable for outdoor use.
Make sure the extension cord is properly wired and in good electrical condition.
Always replace a damaged extension cord or have it repaired by a qualified
electrician before using it.
ꢂ.
Protect the extension cords from sharp objects, excessive heat, and damp or wet
areas.
RECOMMENDED MINIMUM WIRE gAUgE FOR EXTENSION CORDS* (120/240 VOlT)
NAMEPlATE
EXTENSION CORD lENgTH
AMPERES
(at full load)
25 Feet
50 Feet
75 Feet
100 Feet
150 Feet
0 – 2.0
2.1 – 3.4
1ꢂ
1ꢂ
1ꢂ
1ꢂ
1ꢂ
14
12
1ꢂ
1ꢂ
1ꢂ
1ꢀ
14
12
10
1ꢂ
1ꢂ
1ꢀ
14
12
10
-
1ꢂ
1ꢀ
14
12
10
-
1ꢀ
14
12
12
-
3.5 – 5.0
5.1 – ꢁ.0
ꢁ.1 – 12.0
12.1 – 1ꢀ.0
1ꢀ.1 – 20.0
TABlE A
-
-
-
* Based on limiting the line voltage drop to five volts at 150% of the rated amperes.
Symbology
Double Insulated
Volts Alternating Current
Amperes
V~
A
Canadian Standards Association
No Load Revolutions per Minute
(RPM)
Underwriters Laboratories, Inc.
n xxxx/min.
0
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 10
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBlY AND OPERATINg INSTRUCTIONS
Note: For additional references to the parts listed in the following pages, refer to the
Assembly Diagram on page 24.
To Replace And Install A Saw Blade:
1.
WARNINg! Prior to performing any assembly and/or adjustment
procedures, make sure the Power Cord (102) of the Miter Saw is unplugged
from its electrical outlet. Make sure the unit has completely cooled, and
wear heavy-duty work gloves.
2.
When replacing the Saw Blade (5ꢀ), make sure the new Saw Blade has a
diameter of 10”, an RPM rating of at least 7000, and an arbor hole of 5/8”
diameter.
COVER CASE (89)
ARROW
SAW TEETH
POINTINg DOWN
SAW BlADE (56)
ARROW
FIgURE D
3.
4.
When installing a Saw Blade (5ꢀ), make sure the teeth of the Saw Blade point
downward, and that the direction of the arrow shown on the Saw Blade matches
the direction of the arrow shown on the Cover Case (ꢂ9). (See Figure D.)
Lock the Saw Blade (5ꢀ) in its upward position. To do so, pull out on the Cross
Pin (2ꢂ). Raise and hold the Cover Case (ꢂ9) of the Miter Saw fully upward.
Turn the Cross Pin 90 degrees. Then, insert the Cross Pin into the deep slot in
its locked position. (See Figures E and F, next page.)
Rev 07k
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 11
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
CAUTION! The Cross Pin (28) should always be activated in the “locked
down” position when the Saw is not being used and when the Saw is being
transported. The Cross Pin should be activated in the “locked up” position
only when changing Saw Blades. NEVER use the Cross Pin in any cutting
operation. The Cross Pin allows the operator to lock the Saw Blade in position,
preventing the Saw Blade from being raised or lowered. (See Figures E and F.)
CROSS PIN (28)
FIgURE E
SAW BlADE (56)
IN “lOCKED UP” POSITION
FIgURE F
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 12
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ.
ꢁ.
Loosen the Screw (4ꢂ) that holds the Large Cover (4ꢁ) in place. Then, use the
Wrench (110) to remove the Bolt (50). (See Figure g.)
Rotate the Large Cover (4ꢁ) and Safety Cover (53) up and out of the way.
(See Figure g.)
SCREW (48)
lARgE COVER (47)
BOlT (50)
WRENCH (110)
SAFETY COVER (53)
FIgURE g
ꢂ.
Depress the Spindle Lock (ꢂ4) to keep the Saw Blade (5ꢀ) from turning.
(See Figure H.)
SPINDlE lOCK
(84)
FIgURE H
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 13
Download from Www.Somanuals.com. All Manuals Search And Download.
9.
Use the Wrench (109) to unscrew and remove the Spindle Bolt (5ꢂ).
NOTE: The Spindle Bolt unscrews in a clockwise direction. Then, remove
the Outer Flange (5ꢁ). (See Figure I.)
SPINDlE BOlT (58)
ClOCKWISE
TO lOOSEN
COUNTERClOCKWISE
OUTER FlANgE (57)
TO TIgHTEN
FIgURE I
10.
11.
Release pressure on the Spindle Lock (ꢂ4). (See Figure H.)
Wearing heavy duty work gloves to avoid accidental cuts, remove the old Saw
Blade (5ꢀ). (See Figure J.)
SAW BlADE
(56)
FIgURE J
12.
13.
14.
Install the new Saw Blade (5ꢀ), making sure the teeth of the Saw Blade are
pointing downward. (See Figure D.)
Reassemble the Outer Flange (5ꢁ), and Spindle Bolt (5ꢂ) firmly.
(See Figure I.)
Swing the Large Cover (4ꢁ) and Safety Cover (53) back in place, making sure
the Safety Cover covers the Saw Blade (5ꢀ). (See Figure g.)
15.
1ꢀ.
Reinstall the Bolt (50), and retighten the Screw (4ꢂ). (See Figure g.)
Make sure the Safety Cover (53) returns to its original position prior to operating
the Miter Saw.
1ꢁ.
CAUTION! Make sure to pull out on the Cross Pin (28). Turn the Cross
Pin 90 degrees. Then, insert the Cross Pin into the shallow slot in its
unlocked position. NEVER use the Cross Pin in any cutting operation.
(See Figure E.)
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 14
Download from Www.Somanuals.com. All Manuals Search And Download.
To Assemble Additional Accessories:
1.
A workpiece Clamp Assembly (3ꢀ) can be installed by inserting the Assembly into
the hole located in the Guide Fence (3ꢁ). Once inserted, lock the Assembly in
place with the Thumb Screw (35). To clamp the workpiece to the Base (ꢂ) of
the Miter Saw, turn the Adjusting Knob on the Clamp Assembly clockwise.
(See Figure K.)
2.
A workpiece Holder (9) can be inserted into each side of the Base (ꢂ), adjusted
for the desired length, and locked in place with the Thumb Screw (10). The
Holders should be used as supports when cutting longer length workpieces.
(See Figure K.)
ClAMP ASSEMBlY
(36)
THUMB SCREW (35)
gUIDE FENCE (37)
THUMB SCREW (10)
BASE
(8)
HOlDER
FIgURE K
(9)
The Safety Cover:
1.
The transparent Safety Cover (53) automatically rotates to cover the Saw Blade
(5ꢀ) when the Cover Case (ꢂ9) is lifted. When the Cover Case is lowered, the
Safety Cover rotates back out of the way. (See Figure l, next page.)
2.
3.
Do not disconnect or remove the Safety Cover (53). Do not operate the
Miter Saw if the Safety Cover is damaged or missing. (See Figure l.)
If the transparent Safety Cover (53) becomes so dirty that the Saw Blade (5ꢀ)
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 15
Download from Www.Somanuals.com. All Manuals Search And Download.
cannot be seen clearly, disconnect the electrical Power Cord from its electrical
outlet and clean the Safety Cover with a soft, damp, cloth. A mild detergent may
be used, but do not use solvents which may damage the Safety Cover.
(See Figure l.)
COVER CASE (89)
SAFETY COVER (53)
CAUTION!
Never disconnect
or remove
Safety Cover (53).
FIgURE l
The Power Switch:
1. Before plugging in the Miter Saw, check the operation of the Power Switch (9ꢂ).
Do not operate the Miter Saw if the Power Switch is not operating properly. To
turn on the Miter Saw, simply squeeze the Power Switch. To turn off the tool,
release pressure on the Power Switch. (See Figure M.)
POWER SWITCH (98)
FIgURE M
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 1ꢀ
Download from Www.Somanuals.com. All Manuals Search And Download.
The Dust Bag:
1.
2.
The Dust Bag (93) catches and holds the wood chips and saw dust when the
Miter Saw is in operation. (See Figure N.)
The outside diameter of the Dust Tube (94) is 1-3/4” to which the Dust Bag (93)
or a vacuum hose (not included) may be attached. It is recommended that only a
qualified technician perform this procedure. (See Figure N.)
DUST TUBE (94)
DUST BAg (93)
FIgURE N
To Adjust The Cutting Depth:
1.
2.
WARNINg! Prior to performing this procedure, make sure the Power
Cord (102) of the Miter Saw is unplugged from its electrical outlet.
The depth of cut may be adjusted to a maximum of 4-11/1ꢀ” at 90o, and 4-11/1ꢀ”
at 45°.
3.
Slightly loosen the Screw (92) and pull the Miter Saw’s Cover Case (ꢂ9) down-
ward as far as it will go. Observe whether the edge of the Saw Blade (5ꢀ)
passes completely through the Kerf Board (11). (See Figure O, next page. )
4.
5.
If the Saw Blade (5ꢀ) does not pass completely through the Kerf Board (11),
lower the Saw Blade further by loosening the Screw (92). (See Figure O.)
After adjusting the Screw (92), press down on the Miter Saw and make sure the
Saw Blade (5ꢀ) does not contact the bottom of the Table (1ꢂ) or any other part of
the Saw Base (ꢂ). (See Figure O.)
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 1ꢁ
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ.
If the Saw Blade (5ꢀ) touches the Table (1ꢂ) or any other part of the Saw
Base (ꢂ), tighten the Screw (92) to raise the Saw Blade slightly until it clears.
(See Figure O.)
SCREW (92)
TABlE (18)
KERF BOARD (11)
ANglE lOCK (4)
HANDlE (1)
gAUgE (6)
BASE (8)
FIgURE O
To Adjust The Miter Angle:
1.
2.
WARNINg! Prior to performing this procedure, make sure the Power
Cord (102) of the Miter Saw is unplugged from its electrical outlet.
The miter angle of a cut may be adjusted 0 - 45 degrees to the right or left. To do
so, depress the Angle Lock (4) located at the front of the Table (1ꢂ).
(See Figure O.)
3.
While the Angle Lock (4) is depressed, move the Handle (1) to the right or left
until the desired miter angle of cut is indicated by the Gauge (ꢀ) located on the
Base (ꢂ). Then, release pressure on the Angle Lock to lock the Miter Saw in
place. (See Figure O.)
To Adust The Bevel Of Cut:
1.
WARNINg! Prior to performing this procedure, make sure the Power
Cord (102) of the Miter Saw is unplugged from its electrical outlet.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 1ꢂ
Download from Www.Somanuals.com. All Manuals Search And Download.
2.
3.
The bevel angle (or Saw Blade tilt capacity) may be adjusted from 0 - 45o to the
left. To do so, loosen the Handle (30) located at the rear of the Miter Saw.
(See Figure P.)
Tilt the Back Rack (25) until the desired bevel angle of cut is achieved as indi-
cated on the Gauge (24). Then, re-tighten the Handle (30) to lock the Back Rack
in place. (See Figure P.)
FIgURE P
gAUgE
(24)
HANDlE
BACK RACK
(25)
(30)
Basic Operation:
1.
Make sure the Power Cord (102) of the Miter Saw is unplugged from its
electrical outlet. Then, if necessary, make adjustments to the workpiece Holder
(9), cutting depth, miter angle, and bevel angle.
2.
3.
Raise the Saw Blade (5ꢀ) up to allow positioning of the workpiece.
Check to make sure the Power Switch (9ꢂ) is operating properly.
4.
5.
Place the workpiece on the Table (1ꢂ) and against the Guide Fence (3ꢁ).
Use the Clamp Assembly (3ꢀ) to hold the workpiece in place.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 19
Download from Www.Somanuals.com. All Manuals Search And Download.
ꢀ.
Plug the Power Cord (102) into the nearest 120 volt, grounded, electrical
outlet.
ꢁ.
ꢂ.
Squeeze the Power Switch (9ꢂ) to turn on the Miter Saw.
When the Saw Blade (5ꢀ) is turning at full speed, slowly bring down the Motor
Housing (ꢁ5) to complete the cut. NOTE: Feed the Saw Blade into the
workpiece gradually. Do not force the machine to remove material faster than it
was designed to cut.
9.
When cutting a large workpiece, make sure its entire length is properly
supported. If necessary, use a roller stand (not included) with a larger workpiece.
10.
11.
12.
13.
14.
Never attempt to remove material stuck in the moving parts of the Miter Saw
while it is plugged in and running.
Turn off the Miter Saw if the workpiece is to be backed out of an uncompleted
cut.
When the cut is complete, release the Power Switch (9ꢂ) to turn off the Miter
Saw.
Wait until the Saw Blade (5ꢀ) comes to a complete stop. Raise the Motor
Housing (ꢁ5). Then, unplug the Power Cord (102) from its electrical outlet.
Loosen the Clamp Assembly (3ꢀ), and remove the workpiece and scrap material
from the Table (1ꢂ).
INSPECTION, MAINTENANCE, AND ClEANINg
1.
2.
WARNINg! Always make sure the Power Switch (98) is in its “OFF”
position, and unplug the Power Cord (102) from its 120 volt electrical outlet
before performing any inspection, adjustments, maintenance, or cleaning.
Make sure the power tool is cool to the touch before inspection, maintenance,
and cleaning begin. Always protect your hands by wearing work gloves.
Before each use, inspect the general condition of the Miter Saw. Check for
loose screws, misalignment or binding of moving parts, cracked or broken parts,
damaged electrical wiring, loose, cracked, or bent Saw Blade (5ꢀ), and any other
condition that may affect its safe operation. If abnormal noise or vibration occurs,
have the problem corrected before further use.
Do not use damaged equipment. Never work with a dull saw blade.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 20
Download from Www.Somanuals.com. All Manuals Search And Download.
3.
4.
Daily: With a soft brush, cloth, or vacuum, remove all dust and debris from
the Miter Saw. Then, use a premium quality, lightweight machine oil to lubricate
all moving parts except the Saw Blade (5ꢀ).
To replace the Motor Carbon Brushes: It may become necessary at some-
time to replace the two Carbon Brushes (ꢁ3) when the Motor performance de-
creases, or stops working completely. The Carbon Brushes are located on
each side of the Motor Housing (75). To do so, remove the two Brush Covers
(ꢁ2). Then, remove the two Carbon Brushes from the Brush Holders (ꢁ4).
If the Carbon Brushes are worn down more than 1/2, replace both Carbon
Brushes. If, however, the Carbon Brushes are just dirty they may be cleaned by
rubbing them with a pencil eraser. When installing the Carbon Brushes, make
sure the carbon portion of the Carbon Brushes contact the Motor Armature, and
that the springs face away from the Motor. Also, make sure the springs operate
freely. After cleaning or replacement, replace the Brush Holders.
NOTE: New Carbon Brushes tend to arc or spark when first used until they
wear and conform to the Motor’s Armature. (See Figure Q.)
5.
NOTE: With the exceptions of Steps #1, #2, #3, and #4 all other
maintenance and servicing should be performed only by a qualified service
technician.
FIgURE Q
CARBON BRUSH (73)
(NOT SHOWN)
CARBON BRUSH
(73)
PlEASE READ THE FOllOWINg CAREFUllY
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROVIDED THE PARTS LIST AND ASSEMBLY DIAGRAM IN THIS MANUAL
AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER OR DISTRIBUTOR MAKES ANY REPRESENTATION OR
WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT, OR
THAT HE OR SHE IS QUALIFIED TO REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR
DISTRIBUTOR EXPRESSLYSTATESTHATALLREPAIRSAND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN BYCERTIFIED
AND LICENSED TECHNICIANS, AND NOT BY THE BUYER. THE BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF
HIS OR HER REPAIRS TO THE ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 21
Download from Www.Somanuals.com. All Manuals Search And Download.
PARTS lIST
Description
Handle
Part #
1
Part #
56
Description
Saw Blade
2
3
4
5
Screw
57
58
59
60
Outer Flange
Spindle Bolt
Inner Flange
Pin
Spring Gasket
Angle Lock
Slide Way
Gauge
6
61
Arbor
7
Screw
62
Bearing
8
9
Base
Holder
63
64
Bearing Box
Gear
10
11
12
13
14
15
16
17
18
19
20
21
22
23
24
25
26
27
28
29
30
31
32
33
34
35
36
37
38
39
40
41
42
43
44
45
46
47
48
49
50
51
52
53
54
55
Thumb Screw
Kerf Board
Screw
Left Cut Lay
Nut
Pointer
Spring
Screw
Table
Nut
Screw
Gasket
Spring Gasket
Screw
Gauge
Back Rack
Nut
Rubber Ring
Cross Pin
Screw
Handle
Screw
Spring
Spring Base
Small Base
Thumb Screw
Clamp Assembly
Guide Fence
Connecting Bar
Screw
Gasket
Gasket
Gasket
Gasket
Screw
Nut
Small Cover
Large Cover
Screw
65
66
67
68
69
70
71
72
73
74
75
76
77
78
79
80
81
82
83
84
85
86
87
88
89
90
91
92
93
94
95
96
Blind Ring
Needle Bearing
Spring
Spring Cover
Screw
Screw
Spring Gasket
Carbon Brush Cover
Carbon Brush
Carbon Brush Holder
Motor Housing
Screw
Spring Gasket
Gasket
Stator
Windshield Ring
Bearing
Armature
Bearing
Spindle Lock
Middle Cover
Screw
Fixed Rod
Screw
Cover Case
Screw
Rubber Gasket
Screw
Dust Bag
Dust Tube
Hanging Ring
Screw
97
98
99
Switch Gasket
Power Switch
Rubber Buff
Handle (Lower)
Sheathing
Power Cord
Wire Holding Board
Screw
Handle (Upper)
Screw
Nut
Screw
Plate
100
101
102
103
104
105
106
107
108
109
110
Spring
Bolt
Gasket
Screw
Safety Cover
Spring Gasket
Screw
Wrench (Not Shown)
NOTE: Some parts are listed and shown for illustration purposes only, and are not
available individually as replacement parts.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 22
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBlY DIAgRAM
110: WRENCH NOT SHOWN.
NOTE: Some parts are listed and shown for illustration purposes only, and are
not available individually as replacement parts.
SKU 91995
For technical questions, please call 1-800-444-3353.
Page 23
Download from Www.Somanuals.com. All Manuals Search And Download.
|