Coocheer Chainsaw Manual

Models: 50969, 50970, 8901,

8902,9013

14/18/20 INCH CHAINSAW

DO NOT RETURN TO STORE. Please CALL 800-348-5004 for parts and service.

care. Keep this manual in a

CALIFORNIA

PROPOSITION 65

BEFORE OPERATING

THIS CHAINSAW.

safe place, so that the

information is available at all

times. If you give the

equipment to any other

person, give them these

operating instructions as

well. We accept no liability

for damage or accidents

which arise due to non-

observance of these

WARNING: You can create

dust when you cut, sand,

drill or grind materials

such as wood, paint,

metal, concrete, cement,

or other masonry. This

dust often contains

chemicals known to

cause cancer, birth

defects, or other

Any failures made in

following the safety

regulations and and

instructions may result in

an electric shock, fire

and/or serious injury.

SAFETY

INSTRUCTIONS

instructions and the safety

information herein.

Only allow users who have

read and understand this

manual operate this

chainsaw.

reproductive harm. Wear

protective gear.

SPECIFICATIONS

Engine Displacement:45cc

Max. Engine Capacity:

2000W

Bar Length: 14in 18in. and

20in.

Idling Speed: 3000 RPMs

Max. Speed with Cutting

Equipment: 10,000 RPMs

Anti-Vibration Function

Chain Brake

WARNING: This product

or its power cord may

contain chemicals,

including lead, known to

the State of California to

cause cancer and birth

defects or other

reproductive harm. Wash

hands after handling.

Important!

When using equipment, a

few safety precautions must

be observed to avoid

injuries and damage. Please

read the complete operating

manual with due

Wear protective gear, such

as steel-toed footwear,

snugly fitting clothing, heavy

duty gloves, eye protection

(goggles or face screen),

hard hat and ear protection

(ear plugs or mufflers). Do

not wear jewelry and pull

long hair back.

Auto Chain Lubrication

Keep all body parts clear of

the chain while the engine is

running.

CAUTION:

FOR YOUR OWN SAFETY

READ INSTRUCTION

MANUAL COMPLETELY

AND CAREFULLY

Do not allow other people

8850969

08/10

cutting area free from foreign

objects.

Pinch kickback occurs

when the woods closes in on

the moving chain along the

top of the guide bar. The

sudden stop of the chain

results in the saw to move in

the opposite direction of the

rotation and the saw is driven

straight back towards the

operator.

or animals near the saw

when it is running, starting,

or being operated.

Keep your chain properly

tensioned and sharp, along

with properly maintaining the

chainsaw. Failure to do so can

increase the chance of

You must be mentally alert

and in good physical

condition when operating a

chainsaw because the work

is strenuous

kickback occurring.

Begin and continue the cut with

the engine running at full

speed. Use caution while re-

entering a previous cut. Do not

attempt a plunge cut (starting a

cut with the tip of the blade).

Carefully plan your sawing

project before starting. Do

not begin until you are sure

the work area is clean, you

have secure footing and if

you are felling trees, that

you have a planned and

clear retreat path.

Pull in occurs when the

moving chain comes in

contact with a foreign object

in the wood along the bottom

of the guide bar. This sudden

stop pulls the saw forward

and away from the operator

and could possibly cause the

operator to lose control of the

saw.

Maintaining Control of the

Chainsaw

Stand to the left of the saw.

Keep your elbow locked and a

firm grip on the saw.

KICKBACK

WARNING: Kickback is the

backward, upward or

Avoiding Kickback

Keep the thumb on the

sudden movement of the

guide bar that occurs when

the guide bar contacts an

object or when the wood

closes in and pinches the

saw in the cut. The saw

contacting a foreign object

in the wood can also result

in a loss of control.

underside of the handlebar.

Never reverse hand positions

(left hand on handlebar and

right hand on the rear handle).

Be aware of situations or

objects that can cause the

material to pinch the top of or

stop the chain.

Stand slightly to the left side of

the saw to keep your body

from being in a straight line

with the saw. Stand with your

weight evenly balanced

Do not cut more than one log

at a time.

Do not twist the saw when

the bar is withdrawn from an

undercut.

Rotational kickback

occurs when the moving

chain contacts an object

with the upper tip of the

guide bar. This can cause

the chain to dig into the

object, which then stops the

chain for a moment. The

result is a reverse reaction,

which kicks the guide bar up

and back towards the

operator.

between both feet.

Always begin cutting with the

engine at full speed and with

the saw housing resting

against the wood.

Do not overreach because you

could be thrown off balance

and lose control of the saw. Do

not cut above shoulder height

because it is difficult to

Use wedges made of plastic

or wood to hold the cut open.

Never use metal.

maintain proper control of the

saw at that height.

Stay alert. Realize kickback

can occur and keep the

Chain Brake

knob completely by removing

the two nuts.

ADJUSTING CHAIN

TENSION

The chain brake is designed

to stop the chain from

rotating in the event of a

kickback.

2) Remove the clutch cover.

Before adjusting, make

sure the bar knobs are

loosened 1 ½ - 2 turns.

Adjusting the chain tension

with the knobs tight can

cause damage.

3) Slide the guide bar on the

bar bolts until the guide bar

rests against the clutch drum

sprocket.

WARNING: DO NOT RELY

UPON THE CHAIN BRAKE

(OR OTHER SAFETY

FEATURES) TO PROTECT

YOU IN THE EVENT OF A

KICKBACK. Use your

chainsaw properly and under

the correct circumstances to

avoid kickback.

4) Hold the chain with the

drive links as shown. The

drive links should be facing

inward with the cutters facing

to the right, or direction of

rotation.

Checking the Chain

Tension

Check the chain tension by

using a screwdriver to

move the chain along the

bar. If it does not rotate, it

is too tight. If it sags below

the bar, it is too loose.

ASSEMBLY

Wear protective gloves

during assembly due to the

handling of sharp objects.

Adjusting the Chain

Tension

Attaching the Bumper

Spike

The chain stretches slightly

during each use, especially

the first few times the saw

is used. Always check the

chain tension each time the

saw is used and refueled.

The bumper spike may be

used as a pivot when making

a cut.

5) Fit the drive links in the

clutch drum sprocket.

6) Place the chain drive links

into the bar groove.

1) Loosen and remove the

bar knob completely by

loosening the two nuts.

1) Make sure the bar knobs

are loosened 1-1/2 – 2

turns.

7) Pull the guide bar forward

to make sure all of the drive

links are in the bar groove.

2) Remove the clutch cover.

2) Using a screwdriver,

adjust the tension of the

chain. The adjusting pin is

located right below the two

bar knobs.

3) Attach the bumper spike

with the two screws with the

spikes pointing downward.

8) Reinstall the clutch cover.

Make sure the adjusting pin is

aligned with the hole in the

guide bar.

Attaching the Bar and

Chain

CAUTION: Make sure the

adjustment pin aligns with the

hole. Failure to align the pin

and install the cover properly

may result in damage,

possibly permanent, to your

saw.

1) Make sure the saw bottom

is resting on a flat surface.

Be sure the chain brake is

pulled back. Loosen and

remove the bar

3) Turn the screw to the right

to increase the tension and

turn it to the left to release

tension.

3) When refueling, turn the

engine off and let it fuel in a

non-combustible area. Slowly

remove the fuel cap and

refuel the saw.

bar is in the middle of a cut.

4) Do not apply pressure to

the saw at the end of a cut. It

can cause you to lose control

of the saw when the cut is

complete.

4) Using a screwdriver, move

the chain around on the guide

bar to make sure all of the

links are in the bar groove. If

the chain does not rotate, it is

too tight and the adjuster

needs to be loosened.

4) Mix and pour the fuel in a

well-ventilated outdoor area.

Store the fuel in a cool, dry

place. Wipe up fuel spills

before attempting to start the

saw.

5) Make sure the engine is

stopped before setting down

the saw.

6) Make sure your chainsaw

is in good condition before

operating. Do not operate a

saw that is damaged,

improperly adjusted, or not

completely and securely

assembled.

5) Tighten the bar knob

securely after the tension is

adjusted.

5) Start the engine at least

10 feet from the fueling site

6) Store the saw and fuel in

an area where sparks or

open flame will not reach it.

FUELING AND

LUBRICATION

7) Do not carry the saw with

the engine running. Carry the

saw with the engine stopped

and the muffler pointing away

from you, with the guide bar

and chain facing behind you.

The chain should be covered

with a bar cover to ensure

the blade will not cause

harm.

OPERATING

INSTRUCTIONS

Use regular grade unleaded

gasoline mixed with 25:1 2-

cycle engine oil. Do not use a

fuel mixture that has been

stored for more than 90 days.

Warning: The chain must not

move when the engine is

running at an idle speed. If

the chain moves, the

carburetor must be adjusted.

Avoid contact with the muffler

because a hot muffler can

cause serious burns or injury.

The bar and chain require

constant lubrication in order to

function properly. Lubrication

is provided by the oiler

system. Lack of oil will cause

damage to the bar and chain.

Smoke coming from the chain

and discoloration on the bar

are signs the oil is low.

8) Do not run while operating

the chainsaw.

Operation Safety

Instructions

Starting A Cold Engine

1) Do not operate a chainsaw

with one hand.

Hold the saw firmly against

the ground and make sure

the chain is free to move

without contacting any

object.

Fueling Safety Instructions

2) Only operate the chainsaw

in a well-ventilated, outdoor

area.

1) Do not smoke while fueling

or operating the saw.

2) Do not allow sparks or

flame in the area where the

fuel is poured or mixed.

Always allow the engine to

cool before refueling.

3) Make sure that the

1) Move the ON/OFF switch

to the ON position.

chainsaw will not come into

contact with any object while

starting the engine. Do not

start the saw when the guide

2) Pull the choke lever out to

its full extent.

3) Pull the starter rope

quickly with your right hand a

maximum of 5 times. If the

engine sounds as though it is

trying to start before the 5^th

pull, do not pull any more and

immediately go to the next

step.

ON/OFF switch is in the ON

position. The amount of

flooding in the engine will

determine how many pulls

are necessary for it to start.

Do not cut any material other

than wood. Do not cut metal,

plastic, masonry, non-wood

building materials, etc.

If the chain strikes a foreign

object, stop the saw and

inspect the chain for

damage. If damage is

present, repair or replace the

necessary parts.

Checking the Chain Brake

The chain brake should be

checked several times during

use. The engine needs to be

running while this is done

and it is the only time the

saw should be set on the

ground with the engine

running.

4) Push the choke lever fully

in.

5) Pull the starter rope quickly

with your right hand until the

engine starts.

Keep the saw clear of dirt or

sand because even a small

amount could dull the blade

and possibly cause kickback.

6) Allow the engine to run for

approximately 30 seconds

before squeezing and

releasing the throttle trigger,

which will allow the engine to

return to idle speed.

1) Place the saw on the

ground.

Before starting a major

project, practice cutting a few

logs.

2) Grasp the rear handle with

your right hand and the front

with your left.

Important Operation

Reminders

Starting a Warm Engine

1) Place the ON/OFF switch

into the ON position.

3) Apply the full throttle with

your right hand.

Allow the engine to reach full

speed before cutting.

2) Push the choke lever full in.

4) Activate the chain brake

by turning your left wrist

against the hand guard

without letting go of the front

handle.

Begin cutting with the saw

frame resting against the log.

3) Pull on the starter rope

quickly with your right hand

until the engine starts.

Keep the engine at full speed

the entire time you are

cutting.

4) After the engine starts,

squeeze and release the

throttle trigger, this will allow

the engine to return to idle

speed.

The chain should stop

Allow the chain to do the

work for you. Do not apply

excess pressure. Forcing the

cut may cause damage to

the engine, bar and/or chain.

immediately. If the chain

brake fails to activate, take

the saw to an authorized

dealer to have the chain

brake replaced or repaired.

Flooded Engine

When the cut is complete,

release the trigger and allow

the engine to return to idle.

Running the saw at full

If your engine does not start

after 10 pulls, it may be

flooded. It can be cleared of

the excess fuel by following

the warm engine starting

process. Make sure the

CUTTING METHOD

INSTRUCTIONS

Safety Instructions

throttle without cutting can

Check the chain tension

before using the saw for the

first time and after 1 minute

of operation

cause wear to the chainsaw.

of the fall.

the fall. Use wood or plastic

wedges to avoid kickback

and chain damage. Never

use steel or iron wedges.

Do not put pressure on the

saw at the end of a cut in

order to maintain control of

the saw.

Felling Large Trees (6 in. or

larger in diameter)

A notch is cut into the side of

the tree in the desired falling

direction. After a felling cut is

made, the tree will tend to fall

into the notch.

Be alert to signs that the tree

is about to fall, such as

cracking sounds, widening of

the felling cut, or movement

in the branches.

Stop the engine before setting

down the saw.

Tree Felling

Note: If the tree has large

buttress roots, remove them

before making the notch into

the tree. If you use a

chainsaw to remove the

roots, keep the chain from

contacting the ground to

prevent the chain from

dulling.

WARNING: Do not cut near

buildings or electrical wires if

the direction of the fall is

uncertain. Check for broken or

dead branches, which could

fall while cutting. Do not cut at

night or during bad weather. If

the tree falls onto a utility line,

notify the utility company

immediately.

As the tree begins to fall,

stop and put down the saw

and quickly get away on your

planned retreat path.

Do not cut down a partially

fallen tree. Be cautious when

working around partially

fallen trees because they

may be poorly supported. If a

tree does not fall completely,

put the saw aside and pull

down the tree with a cable

winch, block and tackle or a

tractor.

1) Make the notch by cutting

the top of the notch first. Cut

through 1/3 of the diameter

of the tree. Complete the

notch by cutting the bottom

of the notch. Remove the

notch of wood from the tree

once the notch is cut.

Plan your sawing operation in

advance. Clear the work area

in order to have a secure

footing. Evaluate the natural

conditions that could affect the

direction of the fall such as

wind, lean of the tree, weight

and branches on one side,

surrounding trees, decay and

rot.

Cutting A Fallen Tree

(Bucking)

2) After removing the wood,

make the felling cut on the

opposite side of the notch.

Make a cut about two inches

higher than the center of the

notch. This will leave a hinge

between the felling cut and

the notch. The hinge will help

prevent the tree from falling

in the wrong direction. It also

helps hold the tree on the

stump and control the fall.

WARNING: DO NOT stand

on the log that is being cut. If

the log rolls, it can cause loss

of footing and control. Do not

stand downhill of the log

being cut.

Make sure the tree has

enough room to fall. Keep a

distance of at least 2 ½ tree

lengths from the nearest

person or object because

engine noises or the tree

falling can drown out warning

calls.

Only cut one log at a time.

Cut shattered wood carefully.

Sharp pieces of wood could

possibly be thrown back

towards the operator.

Remove all foreign objects

from the tree where the cuts

are going to be made. Plan a

clear retreat path that is

Before the felling cut is

Never allow another person

to hold a small log for cutting,

or use your leg or foot to hold

complete, use wedges, if

necessary, to open the cut

and control the direction of

diagonally back from the line

Use caution when cutting

smaller limbs. Small limbs

may catch in the chain and

be flung towards you or

throw you off balance.

it. Use a sawhorse to cut

small logs.

Always make your first cut on

the compression side of the

log (where the pressure of

the log’s weight is

Do not cut in an area where

logs, roots and limbs are

tangled. Drag the logs into a

clear area before cutting.

concentrated).

Watch out for branches that

are under pressure or bent.

When the wood is cut, the

tension may cause the wood

to be flung.

Bucking Without A Support

Types of Cutting for

Bucking

Using an overcut, cut through

1/3 the diameter of the log.

WARNING: If a saw becomes

pinched in a log, do not try to

force it out. It is possible to

lose control of the saw which

can result in injury and/or

damage to yourself or the

saw. Stop the saw and drive a

plastic or wood wedge into the

cut until the saw can be

removed. Restart the saw and

re-enter the cut. Using a metal

wedge can cause kickback

and chain damage. Do not

attempt to restart your saw

when it is pinched in a log.

Roll the log over and finish

with a second overcut.

Keep your work area clear.

Clear away branches from

the work area in order to

avoid tripping over them.

Watch out for logs with a

compression side to prevent

the saw from being pinched.

Limbing

Bucking Using A Log or

Support Stand

Limbing should only be done

when a tree is already cut

down.

Make your first cut on the

compression side of the log

and extend it 1/3 into the

diameter of the log.

Leave any large limbs under

the tree for support as you

work.

Finish with a second cut.

Start at the base of the tree

and work towards the top.

Small limbs can be removed

in one cut.

Limbing and Pruning

Overcutting is when the

bottom of the saw is against

the top of the log. Use a light,

downward pressure when

overcutting.

WARNING: Be on alert for

kickback. Keep the moving

chain away from any other

branches or objects when

limbing or pruning. Never

climb into a tree to limb or

prune. Do not stand on

ladders, platforms, other logs

or in a position with unsteady

footing.

Keep the tree between you

and the chain. Cut opposite

from the branch being cut.

Undercutting is when the log

is cut from the underside with

the top of the saw against the

log. Use a light upward

pressure. Hold the saw firmly

and maintain control of the

saw because it will tend to

push backwards.

Remove any larger,

supportive branches with the

technique described in

Bucking Without A Support.

Important Safety

Reminders

Always use an overcut to cut

small and free hanging limbs.

Do not use an undercut

because it may cause limbs

to fall and pinch the saw.

Work slowly with both hands

gripping the saw. Maintain

balance and a secure

footing.

DO NOT turn the saw upside

down to undercut. Control of

the saw cannot be maintained

in this position.

Pruning

Maintenance Safety

Instructions

in clean water.

WARNING: Do not prune

limbs that are above shoulder

height. If the branches are

higher than your shoulder,

have a professional perform

the job.

4) Allow the filter to air dry

completely.

1) Be sure to have your

chainsaw regularly serviced

by a qualified dealer.

5) Insert the air filter back

into the chainsaw. Replace

the cover on the chainsaw.

Make sure the cover is fitted

securely and properly before

tightening the screw.

2) Never modify the

chainsaw in any way.

Make your first cut 1/3 of the

way through the limb.

3) Keep the handles clean

and dry, and free from oil or

fuel.

Make the second cut all the

way through the limb. The cut

a third overcut through the

branch, leaving a 1 – 2 inch

collar from the trunk of the

tree.

Fuel Filter Cleaning

4) Make sure the fuel and oil

caps, fasteners and screws

are tightened and secure

after performing

NEVER use the saw without

a fuel filter. After 100 hours of

use, the filter should be

cleaned or replaced, if

damaged.

maintenance.

MAINTENANCE

5) Always wear protective

gloves when performing

maintenance.

Make sure the fuel tank is

empty before changing the

filter.

Maintenance Schedule

Check before each use:

Fuel mixture level

Bar lubrication

6) Do not perform

maintenance while the

engine is hot.

1) Remove the fuel tank cap.

2) Bend a piece of soft wire.

Chain tension

3) Reach into the tank

Air Filter Cleaning

Chain sharpness

opening and hook the fuel

line. Carefully pull the line

towards the opening until you

can reach it with your fingers.

DO NOT pull the hose

For damaged parts

DO NOT clean the air filter in

gasoline or other flammable

solutions. Doing so can

create a fire hazard or

harmful emissions.

For loose caps, fasteners and

parts

Inspect and Clean

Bar: Before each use

Saw: After each use

completely out of the tank.

DO NOT operate the saw

without an air filter. Dust and

dirt will be drawn directly into

the engine and damage it.

Keep the air filter clean.

4) Lift the filter out of the

tank.

Air filter: Every 5 hours of

use

5) Pull off the filter. If it is

damaged, discard and

replace with a new one.

Chain brake: Every 5 hours

of use

1) Remove the top cover by

unscrewing the fastening

screw.

Spark arresting screen and

muffler: Every 25 hours of

use

6) Insert a new filter. Place

the filter into the opening and

push it into the tank. Make

sure it is situated in the lower

corner of the tank. If need

be, use a long screwdriver to

2) Lift out the air filter.

Replace spark plug: Yearly

Replace fuel filter: Yearly

3) Clean the air filter in warm,

soapy water and rinse

move the filter into the

correct position. Be careful

not to damage the filter.

additional adjustment, take

the saw to an authorized

service dealer.

3) Using the lubrication

gun, insert the nose into

the lubrication hole and fill

it with grease until it

appears at the edges of the

tip.

7) Fill the tank with new fuel

mixture.

Chain Bar Maintenance

The chain bar needs to be

regularly lubricated and

maintained in order for it to

work.

Spark Plug

4) Rotate the saw by hand.

Add additional lubrication

until the entire tip has been

greased.

The spark plug must be

cleaned or replaced after

every 20 hours of service.

Tools for lubrication

1) Make sure the ON/OFF

switch is turned off.

A lube gun is recommended,

but not required, for applying

grease to the guide bar

sprocket tip. The gun is

equipped with a needle nose

Many guide bar problems

can be avoided by properly

maintaining the bar and

chain saw. Insufficient

2) Remove the top cover by

unscrewing the fastener.

lubrication or using a saw

3) Remove the air filter.

tip, which allows the grease to with a chain that is too tight

be efficiently applied.

will cause the bar to wear

rapidly.

4) Disconnect the ignition

cable from the spark plug by

pulling and twisting

Lubricating the sprocket tip

Maintaining the chain bar

The sprocket tip on your new

saw has been pre-lubricated

in the factory. It needs to be

lubricated properly otherwise

it will perform poorly, and

possibly seize. Lubrication is

recommended once a week or remove burs and square

after 10 hours of use. Clean

the bar tip before lubrication.

simultaneously.

The bar should be

5) Remove the spark plug

by using a spark plug

wrench.

reversed after 8 hours of

work to keep uniform wear.

Check the bar frequently

for wear, and if need be,

6) Clean the spark plug with

a copper wire brush. The

electrode gap should be

0.6mm.

up the rails by using the flat

file.

The chain does not have to be 1) Be sure the ON/OFF

7) Reconnect the ignition

cable.

removed to lubricate the bar

tip. Lubrication is possible

while working, however the

engine must be turned off.

switch is Off.

2) Loosen the bar knob

and remove the cover.

8) Replace the air filter.

9) Replace the top cover,

make sure the cover is

securely fitted, and then

screw down the fastener.

3) Remove the chain and

bar from the saw.

Warning: Wear work gloves

when handling the chain and

bar.

4) Clean the oil holes and

bar groove.

Carburetor

1) Make sure the engine is off,

with the ON/OFF switch in the 5) If the bar is burred,

The carburetor has already

been properly adjusted at

the factory. If it requires

Off position.

remove the burs with a flat

file.

2) Clean the guide bar tip.

6) If the rail top is uneven,

use a flat file to make the

sides and edges square

again.

underside of the chainsaw. By

turning the screw

counterclockwise, it will

increase the lubrication and

turning it clockwise will

decrease the lubrication.

STORAGE

If a chainsaw is going to be in

storage for longer than 30

days, follow these

Replace the guide bar when

the groove is worn, the bar

is bent or cracked, or when

excessive heating or burring

occurs. If the bar needs

replacing, only use the

guide bar specified in the

parts list or on the chain

saw.

instructions.

Storing a chainsaw

To check the lubrication, hold

the chain saw over a piece of

paper and run it at full speed

for a few seconds. The

amount of oil on the paper will

determine if the lubrication

needs to be increased or not.

1) Remove the fuel tank

slowly in order to release any

pressure in the tank. Carefully

drain the fuel from the tank.

2) To remove all of the fuel

from the carburetor, start the

engine and let it run until the

saw stops.

Oil passages

Chain Maintenance

Sharpening

The oil passages should be

cleaned to allow proper

lubrication of the bar and

chain.

3) Allow the engine to cool

completely.

Chain sharpening requires

special tools to ensure that

the cutters are sharpened to

the proper angle and depth.

We recommend you allow a

professional chain sharpener

to sharpen your chain.

4) Remove the spark plug.

The condition of the

5) Pour 1 teaspoon of 2-cycle

oil into the combustion

chamber. Slowly pull the

starter rope a few times in

order to coat the internal

parts. Replace spark plug.

passages can be checked.

If they are clear, the chain

will automatically send off a

spray of oil within seconds

of starting the saw because

it is equipped with an

Breaking in a new chain

Note: Store the unit away

from water, sources of flame

and sparks and in a cool, dry

location.

automatic oiler system.

A new chain and bar will need

adjusting after as few as 5

cuts. This is normal during the

break-in period and the

interval between future

adjustments will begin to

lengthen.

Automatic chain

lubrication

The chain is equipped with

an automatic oil system with

a toothed wheel drive. It will

automatically supply the bar

and chain with the right

amount of oil. When the

engine is accelerated, the

oil will flow through the bar

more quickly.

Preparation to use saw

again

1) Remove the spark plug.

Chain lubrication

2) Pull the starter rope briefly

to clear excess oil from the

combustion chamber.

Make sure the oil tank is filled

with the appropriate oil to

lubricate the chain. Running

the saw with low or no oil will

cause damage to the chain

and the saw, causing

3) Clean the spark plug and

check the electrode gap.

4) Replace the spark plug.

The lubrication system has

been set at the factory. The

screw for adjusting the

5) Fill the fuel tank with the

proper fuel mixture.

overheating and excessive

wear.

lubrication is located on the

6) Check oil levels.

Symptom

Possible Cause(s)

Corrective Action

Ignition switch is not ON

Engine is flooded

Turn ignition switch ON

Reference Digital Starting section of

manual

Fuel tank is empty

Fill tank with proper fuel mixture

Install new spark plug

Engine will not start or

will not stay running

Spark plug is not working properly

Check for dirty fuel filter (replace if

need be). Check for faulty fuel line

(repair or replace if need be).

Fuel is not reaching the carburetor

Carburetor requires adjustment

Crankshaft seal is worn

Contact an authorized service dealer

Engine will not idle

properly

Air Filter is dirty

Clean or replace air filter

Engine will not accelerate,

lacks power or dies under

a load

Spark plug is faulty

Clean or replace plug or correct gap

Chain brake is engaged

Disengage chain brake

Carburetor needs adjustment

Contact an authorized service dealer

Engine smokes

excessively

Empty fuel tank and refill with proper

fuel mixture

Too much oil mixed with gasoline

Idle speed requires adjustment

Clutch requires repair

Contact an authorized service dealer

Contact an authorized service repair

Chain moves while idling

North American Tool (NAT) Industries makes every effort to ensure that this product meets

high quality and durability standards. NAT warrants to the original retail consumer a 1-year

limited warranty from the date the product was purchased at retail and each product is free

from defects in materials. Warranty does not apply to defects due directly or indirectly to

misuse, abuse, negligence or accidents, repairs or alterations, or a lack of maintenance.

NAT shall in no event be liable for death, injuries to persons or property, or for incidental,

special or consequential damages arising from the use of our products. To receive service

under warranty, the original manufacturer part must be returned for examination by an

authorized service center. Shipping and handling charges may apply. If a defect is found,

NAT will either repair or replace the product at its discretion.

DO NOT RETURN TO STORE.

Please CALL 800-348-5004 for parts and service.

14/18/20 INCH CHAINSAW

Models: 50969, 50970, 8901,

8902,9013

8850969

08/10

14/18/20 INCH CHAINSAW

Models: 50969, 50970, 8901,

8902,9013

8850969

08/10

Ref No.

Name

retainer ring

screw

Quantity

Ref No.

Name

screw

air filter

throttle rod

Quantity

Ref No.

115

116

117

118

119

120

121

122

123

124

125

126

127

128

129

130

131

132

133

134

135

136

137

138

139

140

141

142

143

144

145

146

147

148

149

150

151

152

153

154

155

156

157

158

159

160

161

162

163

164

165

166

167

168

169

Name

big washer

cooling-air mask

dust cover

Quantity

air intake tube

air intake tube gasket

cylinder

spark plug LD

screw

spring washer 5

washer 5

silencer bolt

silencer gasket

silencer

screw

silencer cap

nut M5

screw

throttle lever retainer

anti-shock block

oil seal

oil pump cover plate

screw

worm

needle bearing

sprocket

double-ended pin

anti-vibaration cushion c

fuel cap

packing washer

fuel cap retainer

button

button spring

button shaft

base

screw

trigger controller

handle cover

trigger

clutch shell

clutch washer

clutch extension spring

retainer

cylinder gasket

piston ring

piston

piston pin circlip

piston pin

shoe bolck

screw

oil nozzle

oil pump

sponge ring

oil tube

trigger torsion rod spring

balancer cover

filter

balancer rubber

balancer body

fuel tube

fuel tube base

fuel filter components

tightener

tightening screw

tightening gear

brake spring cover

screw

needle bearing ring

needle bearing

crankshaft components

semicircular key

flameout wire

igniter

oil filter body

oil filter sereen

protecting shield

protecting shield cover

chain guide

oil cap retainer

packing washer

oil cap

screw

nut

spring washer 8

flywheel

screw

spring washer 4

washer 4

oil seal protector

oil seal

screw

spiked bumper

sponge block

aeration nozzle circlip

aeration nozzle

suction tube circlip

suction tube

suction nozzle

air filter lock nut

lock nut washer

air filter cover

shock rubber cushion

upper cover plate

screw

chain catcher

screw

conical spring base

conical spreader spring

idle adjusting guide

screw

shock rubber washer

shield ring

washer

brake torsion rod spring

front guard tube

tightener cover

dust shield

ring 35

brake belt

chain guide

nut

right cover

bearing 6202 grade D

anti-vibaration cushion d

left crankshaftcase

flameout switch

ground strip

flameout switch retainer

crankshaftcase gasket

100

101

102

103

104

105

106

107

108

109

110

111

112

113

114

shock rubber cushion

cam piate

shield ring

front guard pin

shield ring

dust plate

front handle assembly

kick spring base

kick spring

front guard

right crankshaftcase

backing board

air intake tube support

positioning pin

secondarybrake spring

brake spring

brake control rod

starter cover

start rope

L H sheathing

coil spring

starting handle

coil spring shell

starter wheel

52 air intake tube support gaske

air intake flange

carburetor

accelerator rod

air intake

secondarypull-rod

main pull-rod

air intake cushion

Zenoah Chainsaw G4200EZ User Manual
Zenoah Chainsaw G3801 User Manual
Poulan Chainsaw 952802326 User Manual
Multiquip Chainsaw MVH 120GH User Manual
Husqvarna Chainsaw 338XPT Manual