27051
16" Variable Speed Scroll Saw
®
with Quickset II Blade
Changing Feature
(Models SS350, SS350LS)
PART NO. 912425 - 08-25-03
Copyright © 2003 Delta Machinery
To learn more about DELTA MACHINERY
visit our website at: www.deltamachinery.com.
RTD10000121AA
For Parts, Service, Warranty or other Assistance,
please call 1-800-223-7278 (In Canada call 1-800-463-3582).
Download from Www.Somanuals.com. All Manuals Search And Download.
SAFETY GUIDELINES - DEFINITIONS
This manual contains information that is important for you to know and understand. This information relates to protect-
ing YOUR SAFETY and PREVENTING EQUIPMENT PROBLEMS. To help you recognize this information, we use the
symbols to the right. Please read the manual and pay attention to these sections.
Indicates an imminently hazardous situation which, if not avoided, will result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, could result in death or serious injury.
Indicates a potentially hazardous situation which, if not avoided, may result in minor or moderate injury.
Used without the safety alert symbol indicates potentially hazardous situation which, if not avoided, may
result in property damage.
SOME DUST CREATED BY POWER SANDING, SAWING, GRINDING, DRILLING, AND OTHER
CONSTRUCTION ACTIVITIES contains chemicals known to cause cancer, birth defects or other reproductive harm.
Some examples of these chemicals are:
· lead from lead-based paints,
· crystalline silica from bricks and cement and other masonry products, and
· arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you do this type of work. To reduce your exposure to
these chemicals: work in a well ventilated area, and work with approved safety equipment, always wear MSHA/NIOSH
approved, properly fitting face mask or respirator when using such tools.
GENERAL SAFETY RULES
READ AND UNDERSTAND ALL WARNINGS AND OPERATING INSTRUCTIONS BEFORE
USING THIS EQUIPMENT. Failure to follow all instructions listed below, may result in electric shock,
fire, and/or serious personal injury or property damage.
IMPORTANT SAFETY INSTRUCTIONS
Woodworking can be dangerous if safe and proper operating procedures are not followed. As with all machinery, there
are certain hazards involved with the operation of the product. Using the machine with respect and caution will
considerably lessen the possibility of personal injury. However, if normal safety precautions are overlooked or ignored,
personal injury to the operator may result. Safety equipment such as guards, push sticks, hold-downs, featherboards,
goggles, dust masks and hearing protection can reduce your potential for injury. But even the best guard won’t make
up for poor judgment, carelessness or inattention. Always use common sense and exercise caution in the workshop.
If a procedure feels dangerous, don’t try it. Figure out an alternative procedure that feels safer. REMEMBER: Your
personal safety is your responsibility. For additional information please visit our website www.deltamachinery.com.
This machine was designed for certain applications only. Delta Machinery strongly recommends that this
machine not be modified and/or used for any application other than that for which it was designed. If you have any
questions relative to a particular application, DO NOT use the machine until you have first contacted Delta to determine
if it can or should be performed on the product.
Technical Service Manager
Delta Machinery
4825 Highway 45 North
Jackson, TN 38305
(IN CANADA: 505 SOUTHGATE DRIVE, GUELPH, ONTARIO N1H 6M7)
2
Download from Www.Somanuals.com. All Manuals Search And Download.
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1.
2.
FOR YOUR OWN SAFETY, READ THE INSTRUC-
13. USE RECOMMENDED ACCESSORIES. The use
of accessories and attachments not recom-
mended by Delta may cause damage to the
machine or injury to the user.
TION MANUAL BEFORE OPERATING THE
MACHINE. Learning the machine’s application,
limitations, and specific hazards will greatly
minimize the possibility of accidents and injury.
14. USE THE PROPER EXTENSION CORD. Make
sure your extension cord is in good condition.
When using an extension cord, be sure to use one
heavy enough to carry the current your product will
draw. An undersized cord will cause a drop in line
voltage, resulting in loss of power and overheating.
See the Extension Cord Chart for the correct size
depending on the cord length and nameplate
ampere rating. If in doubt, use the next heavier
gauge. The smaller the gauge number, the heavier
the cord.
15. SECURE THE WORKPIECE. Use clamps or a vise to
hold the workpiece when practical. Loss of control
of a workpiece can cause injury.
16. FEED THE WORKPIECE AGAINST THE DIRECTION
OF THE ROTATION OF THE BLADE, CUTTER, OR
ABRASIVE SURFACE. Feeding it from the other
direction will cause the workpiece to be thrown out
at high speed.
USE CERTIFIED SAFETY EQUIPMENT. Eye
protection equipment should comply with ANSI
Z87.1 standards, hearing equipment should
comply with ANSI S3.19 standards, and dust mask
protection should comply with MSHA/NIOSH
certified respirator standards. Splinters, air-borne
debris, and dust can cause irritation, injury, and/or
illness.
DRESS PROPERLY. Do not wear tie, gloves, or
loose clothing. Remove watch, rings, and other
jewelry. Roll up your sleeves. Clothing or jewelry
caught in moving parts can cause injury.
DO NOT USE THE MACHINE IN A DANGEROUS
ENVIRONMENT. The use of power tools in damp
or wet locations or in rain can cause shock or
electrocution. Keep your work area well-lit to
prevent tripping or placing arms, hands, and
fingers in danger.
3.
4.
5.
6.
MAINTAIN ALL TOOLS AND MACHINES IN PEAK
CONDITION. Keep tools sharp and clean for best and
safest performance. Follow instructions for lubricating
and changing accessories. Poorly maintained tools and
machines can further damage the tool or machine and/or
cause injury.
CHECK FOR DAMAGED PARTS. Before using the
machine, check for any damaged parts. Check for
alignment of moving parts, binding of moving
parts, breakage of parts, and any other conditions
that may affect its operation. A guard or any other
part that is damaged should be properly repaired
or replaced. Damaged parts can cause further
damage to the machine and/or injury.
17. DON’T FORCE THE WORKPIECE ON THE
MACHINE. Damage to the machine and/or injury
may result.
18. DON’T OVERREACH. Loss of balance can make
you fall into a working machine, causing injury.
19. NEVER STAND ON THE MACHINE. Injury could occur if
the tool tips, or if you accidentally contact the cutting tool.
20. NEVER LEAVE THE MACHINE RUNNING UNATTEN-
DED. TURN THE POWER OFF. Don’t leave the machine
until it comes to a complete stop. A child or visitor could
be injured.
21. TURN THE MACHINE “OFF”, AND DISCONNECT THE
MACHINE FROM THE POWER SOURCE before
installing or removing accessories, before adjusting
or changing set-ups, or when making repairs. An
accidental start-up can cause injury.
22. MAKE YOUR WORKSHOP CHILDPROOF WITH
PADLOCKS, MASTER SWITCHES, OR BY
REMOVING STARTER KEYS. The accidental
start-up of a machine by a child or visitor could
cause injury.
23. STAY ALERT, WATCH WHAT YOU ARE DOING,
AND USE COMMON SENSE. DO NOT USE THE
MACHINE WHEN YOU ARE TIRED OR UNDER
THE INFLUENCE OF DRUGS, ALCOHOL, OR
MEDICATION. A moment of inattention while
operating power tools may result in injury.
7.
8.
KEEP THE WORK AREA CLEAN. Cluttered areas and
benches invite accidents.
KEEP CHILDREN AND VISITORS AWAY. Your shop is
a potentially dangerous environment. Children and visitors
can be injured.
REDUCE THE RISK OF UNINTENTIONAL STARTING.
Make sure that the switch is in the “OFF” position
before plugging in the power cord. In the event of
a power failure, move the switch to the “OFF”
position. An accidental start-up can cause injury.
9.
10. USE THE GUARDS. Check to see that all guards
are in place, secured, and working correctly to
prevent injury.
11. REMOVE ADJUSTING KEYS AND WRENCHES
BEFORE STARTING THE MACHINE. Tools, scrap
pieces, and other debris can be thrown at high
speed, causing injury.
12. USE THE RIGHT MACHINE. Don’t force a
machine or an attachment to do a job for which it
was not designed. Damage to the machine and/or
injury may result.
24. THE DUST GENERATED by certain woods and
wood products can be injurious to your health.
Always operate machinery in well-ventilated areas,
and provide for proper dust removal. Use wood
dust collection systems whenever possible.
3
Download from Www.Somanuals.com. All Manuals Search And Download.
ADDITIONAL SAFETY RULES
FOR SCROLL SAWS
FAILURE TO FOLLOW THESE RULES MAY RESULT IN SERIOUS PERSONAL INJURY.
1. DO NOT OPERATE THIS MACHINE until it is
assembled and installed according to the instructions.
2. OBTAIN ADVICE FROM YOUR SUPERVISOR,
instructor, or another qualified person if you are not
familiar with the operation of this machine.
21. DO NOT feed the material too fast while cutting.
Only feed the material fast enough so that the blade will
cut.
22. NEVER start the Scroll Saw with the stock pressed
against the blade.
3. FOLLOW ALL WIRING CODES and recommended
electrical connections.
23. WHEN cutting a large workpiece MAKE SURE the
material is supported at table height.
4. YOUR SCROLL SAW MUST be securely fastened
to a stand or workbench. If there is any tendency for the
stand or workbench to move during operation, the stand
or workbench MUST be fastened to the floor.
24. USE CAUTION when cutting material which is
irregular in cross section which could pinch the blade
before the cut is completed. A piece of moulding for
example must lay flat on the table and not be permitted
to rock while being cut.
5. THIS SCROLL SAW is intended for indoor use only.
6. MAKE SURE blade is properly tensioned before
operating saw.
7. TO AVOID blade breakage ALWAYS adjust blade
tension correctly.
25. USE CAUTION when cutting round material such as
dowel rods or tubing. They have a tendency to roll while
being cut causing the blade to "bite." Use a V-block to
control the piece.
26. ALWAYS release blade tension before removing the
blade from the upper or lower blade holders.
8. MAKE SURE the blade teeth point downward
toward the table.
27. MAKE CERTAIN table tilting lock is tightened
before starting the machine.
9. NEVER turn the saw "ON" before clearing the table
of all objects (tools, scraps of wood, etc.).
28. NEVER reach under the table while the machine is
running.
10. DO NOT cut material that is too small to be safely
supported.
29. NEVER perform layout, assembly or set-up work on
the table while the saw is operating.
11. AVOID awkward hand positions where a sudden slip
could cause a hand to move into the blade.
30. ALWAYS STOP the saw before removing scrap
pieces from the table.
12. ALWAYS keep hands and fingers away from blade.
13. ALWAYS adjust holddown foot for each new
operation.
14. DO NOT USE dull or bent blades.
15. DO NOT attempt to saw material that does not have
a flat surface, unless a suitable support is used.
16. MAKE "relief" cuts before cutting long curves.
17. NEVER attempt to cut a curve that is too tight for
the blade being used.
18. WHEN backing a blade out of a workpiece, the
blade may bind in the saw kerf. This is usually caused by
sawdust in the kerf. If this happens, turn "OFF" the
switch and remove plug from power source outlet.
Wedge open the kerf and back blade out of the
workpiece.
19. THE USE of attachments and accessories not
recommended by Delta may result in the risk of injuries.
20. ALWAYS hold the work firmly against the table.
31. TURN THE MACHINE “OFF” AND DISCONNECT
THE MACHINE from the power source before installing
or removing accessories, before adjusting or changing
set-ups, or when making repairs.
32. TURN THE MACHINE “OFF”, disconnect the
machine from the power source, and clean the
table/work area before leaving the machine. LOCK THE
SWITCH IN THE “OFF” POSITION to prevent
unauthorized use.
33. ADDITIONAL INFORMATION regarding the safe
and proper operation of this tool is available from the
Power Tool Institute, 1300 Summer Avenue, Cleveland,
OH 44115-2851. Information is also available from the
National Safety Council, 1121 Spring Lake Drive, Itasca,
IL 60143-3201. Please refer to the American National
Standards Institute ANSI 01.1 Safety Requirements for
Woodworking Machines and the U.S. Department of
Labor OSHA 1910.213 Regulations.
SAVE THESE INSTRUCTIONS.
Refer to them often and use them to instruct others.
4
Download from Www.Somanuals.com. All Manuals Search And Download.
POWER CONNECTIONS
A separate electrical circuit should be used for your machines. This circuit should not be less than #12 wire and should
be protected with a 20 Amp time lag fuse. If an extension cord is used, use only 3-wire extension cords which have 3-
prong grounding type plugs and matching receptacle which will accept the machine’s plug. Before connecting the
machine to the power line, make sure the switch is in the “OFF” position and be sure that the electric current is of the
same characteristics as indicated on the machine. All line connections should make good contact. Running on low
voltage will damage the machine.
DO NOT EXPOSE THE MACHINE TO RAIN OR OPERATE THE MACHINE IN DAMP LOCATIONS.
MOTOR SPECIFICATIONS
Your machine is wired for 120 volt, 60 HZ alternating current. Before connecting the machine to the power source,
make sure the switch is in the “OFF” position.
GROUNDING INSTRUCTIONS
THIS MACHINE MUST BE GROUNDED WHILE IN USE TO PROTECT THE OPERATOR FROM
ELECTRIC SHOCK.
1. All grounded, cord-connected machines:
2. Grounded, cord-connected machines intended for use
on a supply circuit having a nominal rating less than 150
volts:
In the event of a malfunction or breakdown, grounding
provides a path of least resistance for electric current to
reduce the risk of electric shock. This machine is
equipped with an electric cord having an equipment-
grounding conductor and a grounding plug. The plug must
be plugged into a matching outlet that is properly installed
and grounded in accordance with all local codes and
ordinances.
If the machine is intended for use on a circuit that has an
outlet that looks like the one illustrated in Fig. A, the
machine will have a grounding plug that looks like the plug
illustrated in Fig. A. A temporary adapter, which looks like
the adapter illustrated in Fig. B, may be used to connect
this plug to a matching 2-conductor receptacle as shown
in Fig. B if a properly grounded outlet is not available. The
temporary adapter should be used only until a properly
grounded outlet can be installed by a qualified electrician.
The green-colored rigid ear, lug, and the like, extending
from the adapter must be connected to a permanent
ground such as a properly grounded outlet box. Whenever
the adapter is used, it must be held in place with a metal
screw.
Do not modify the plug provided - if it will not fit the outlet,
have the proper outlet installed by a qualified electrician.
Improper connection of the equipment-grounding
conductor can result in risk of electric shock. The
conductor with insulation having an outer surface that is
green with or without yellow stripes is the equipment-
grounding conductor. If repair or replacement of the
electric cord or plug is necessary, do not connect the
equipment-grounding conductor to a live terminal.
NOTE: In Canada, the use of a temporary adapter is not
permitted by the Canadian Electric Code.
Check with a qualified electrician or service personnel if
the grounding instructions are not completely
understood, or if in doubt as to whether the machine is
properly grounded.
IN ALL CASES, MAKE CERTAIN
THE
RECEPTACLE IN QUESTION IS PROPERLY
GROUNDED. IF YOU ARE NOT SURE HAVE A
QUALIFIED ELECTRICIAN CHECK THE RECEPTACLE.
Use only 3-wire extension cords that have 3-prong
grounding type plugs and matching 3-conductor
receptacles that accept the machine’s plug, as shown in
Fig. A.
Repair or replace damaged or worn cord immediately.
GROUNDED OUTLET BOX
GROUNDED OUTLET BOX
GROUNDING
MEANS
CURRENT
CARRYING
PRONGS
ADAPTER
GROUNDING BLADE
IS LONGEST OF THE 3 BLADES
Fig. A
Fig. B
5
Download from Www.Somanuals.com. All Manuals Search And Download.
EXTENSION CORDS
Use proper extension cords. Make sure your extension cord is in good condition and is a 3-wire
extension cord which has a 3-prong grounding type plug and matching receptacle which will accept the machine’s
plug. When using an extension cord, be sure to use one heavy enough to carry the current of the machine. An
undersized cord will cause a drop in line voltage, resulting in loss of power and overheating. Fig. D, shows the correct
gauge to use depending on the cord length. If in doubt, use the next heavier gauge. The smaller the gauge number,
the heavier the cord.
MINIMUM GAUGE EXTENSION CORD
RECOMMENDED SIZES FOR USE WITH STATIONARY ELECTRIC MACHINES
Ampere
Rating
Total Length
of Cord in Feet
Gauge of
Extension Cord
Volts
0-6
0-6
0-6
0-6
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
16 AWG
14 AWG
6-10
6-10
6-10
6-10
120
120
120
120
up to 25
25-50
50-100
100-150
18 AWG
16 AWG
14 AWG
12 AWG
10-12
10-12
10-12
10-12
120
120
120
120
up to 25
25-50
50-100
100-150
16 AWG
16 AWG
14 AWG
12 AWG
12-16
12-16
12-16
120
120
120
up to 25
25-50
14 AWG
12 AWG
GREATER THAN 50 FEET NOT RECOMMENDED
Fig. D
FUNCTIONAL DESCRIPTION
FOREWORD
Delta ShopMaster Models SS350 and SS350LS 16" Scroll Saws are designed to give high quality, smooth cutting
performance with capacity to cut up to 16" wide by 2" thick woodworking materials and have a 3/4" stroke. Delta
ShopMaster Models SS350 and SS350LS come equipped with; integral dust port, variable speed 600-1650 spm, lock-
out switch, cast iron table for minimal vibration, Quickset II® Blade Chuck System for ergonomic “wrench-free” blade
changing; accepts wide variety of 5" flat end blades; 45° left tilting for bevel cuts; adjustable dust blower to keep cutting
line free of dust. The Delta Model SS350LS also comes with a stand.
UNPACKING AND CLEANING
Carefully unpack the machine and all loose items from the shipping container(s). Remove the protective coating from
all unpainted surfaces. This coating may be removed with a soft cloth moistened with kerosene (do not use acetone,
gasoline or lacquer thinner for this purpose). After cleaning, cover the unpainted surfaces with a good quality household
floor paste wax.
NOTICE: THE MANUAL COVER PHOTO ILLUSTRATES THE CURRENT
PRODUCTION MODEL. ALL OTHER ILLUSTRATIONS ARE REPRESENTATIVE
ONLY AND MAY NOT DEPICT THE ACTUAL COLOR, LABELING OR
ACCESSORIES AND MAY BE INTENDED TO ILLUSTRATE TECHNIQUE ONLY.
6
Download from Www.Somanuals.com. All Manuals Search And Download.
CARTON CONTENTS
MODEL SS350LS
ONLY
2
3
4
5
6
1
7
MODEL SS350LS
ONLY
9
11
8
10
12
13
Fig. 1
1. Scroll Saw
6. Upper Back Brace 12" Long (1)
7. Stand Leg Foot (3)
FOR MODEL SS350LS ONLY
8. 5/16-18x1½" Hex Head Screw (3)
9. 5/16" Flat Washer (6)
2. Stand Leg (3)
10. 5/16" Lockwasher (3)
3. Lower Side Brace 30" Long (2)
4. Upper Side Brace 22½" Long (2)
5. Lower Back Brace 18½" Long (1)
11. 5/16-18 Hex Nut (3)
12. M8x16mm Carriage Head Screw (12)
13 M8x1.25 Flange Hex Nut (12)
7
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
FOR YOUR OWN SAFETY, DO NOT CONNECT THE MACHINE TO THE POWER SOURCE UNTIL
THE MACHINE IS COMPLETELY ASSEMBLED AND YOU READ AND UNDERSTAND THE ENTIRE
INSTRUCTION MANUAL.
6
4
STAND
(FOR MODEL SS350LS ONLY)
4
NOTE: THE ASSEMBLY OF THIS STAND WILL USE
M8X16MM CARRIAGE HEAD SCREWS AND M8
FLANGED HEX NUTS. KEEP THE HEAD OF THE
CARRIAGE HEAD SCREWS TO THE OUTSIDE OF THE
STAND WITH THE FLANGED HEX NUTS TO THE
INSIDE OF THE STAND.
2
2
5
3
NOTE: MAKE SURE THAT THE SHELF ON THE
BRACES ARE ON TOP WHEN ATTACHING THE
BRACES TO THE LEGS.
3
7
7
Assemble stand as shown in Fig. 2 using parts shown in
Fig. 1. The braces, legs and feet are labeled the same in
both illustrations. Insert the M8x1.25x16mm carriage
head screws through legs and braces then secure with
the M8x1.25 flange hex nuts. Loosely tighten hardware
at this time.
A
B
NOTE: MAKE SURE THAT THE DIMPLES ON THE
LEGS (A) FIG. 2 ARE ENGAGED WITH THE HOLES
ON THE BRACES (B).
Fig. 2
SCROLL SAW TO STAND
(FOR MODEL SS350LS ONLY)
1. Place the scroll saw on the top braces of the stand
Fig. 3.
2. Align the three holes (A) Fig. 3, (two of which are
shown), with the three holes in the top of the stand.
A
3. Place a 5/16" flat washer on a 5/16-18x1½" hex
head screw, insert the screw through the hole in the
base of the scroll saw and the hole in the stand. Place a
5/16" flat washer, 5/16" lockwasher and thread a 5/16-
18 hex nut onto the screw. Repeat this process for the
two remaining holes in the scroll saw base and stand.
A
4. Tighten all stand hardware securely.
Fig. 3
8
Download from Www.Somanuals.com. All Manuals Search And Download.
FASTENING SCROLL SAW
TO SUPPORTING SURFACE
This scroll saw MUST be securely fastened to a stand or
workbench using the three holes, two of which are
shown at (A) Fig. 4. The third hole is at the rear of the
machine.
An alternate method of securing the scroll saw to a sup-
porting surface is to fasten the scroll saw to a mounting
board. Then securely clamp the mounting board to a
stand or workbench using two or more C-clamps.
NOTE: For proper stability, the holes in the mounting
board must be countersunk at the bottom so that the
fastener heads are flush with the bottom surface of the
mounting board.
A
Fig. 4
OPERATING CONTROLS AND ADJUSTMENTS
ON-OFF AND VARIABLE
SPEED SWITCH
The on-off switch (A) Fig. 5, and variable speed control
(B) is located on the right side of the scroll saw base. To
turn the saw "ON," move the switch (A) up to the “ON”
position. To turn the saw "OFF", move the switch (A)
down to the “OFF” position.
The scroll saw is equipped with a variable speed control
(B) Fig. 5. The variable speed range is 600 to 1650
B
strokes per minute. When the variable speed knob (B)
Fig. 5, is rotated all the way to the left (counterclockwise)
the speed will be 600 strokes per minute. To increase the
speed, rotate knob (B) to the right (clockwise) until the
A
Fig. 5
desired speed is obtained. When the knob (B) is rotated
all the way to the right (clockwise) the speed will be 1650
strokes per minute.
LOCKING ON-OFF SWITCH
IN THE "OFF" POSITION
IMPORTANT: When the machine is not in use, the switch
should be locked in the OFF position to prevent
unauthorized use. This can be done by grasping the
switch toggle (B) and pulling it out of the switch, as
shown in Fig. 6. With the switch toggle (B) removed, the
B
switch will not operate. However, should the switch
toggle be removed while the saw is running, the switch
can be turned “OFF” once, but cannot be restarted
without inserting the switch toggle (B).
Fig. 6
9
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING BLADE
TENSION
A
Tension is applied to the blade when the blade tension
lever (A) Fig. 7, has been adjusted and is in the vertical
position as shown. When the blade tension lever (A) is
moved to the horizontal position, as shown in Fig. 8,
blade tension is released.
To adjust blade tension, position lever (A) in the vertical
position, as shown in Fig. 7. To increase tension, turn
lever (A) clockwise and to decrease tension turn lever (A)
counterclockwise. When adjusting tension, turn lever
one-quarter of a turn at a time. NOTE: It is necessary to
adjust the blade tension only when the blade is removed
from both the upper and lower blade holders and a new
or different type of blade is used. It is not necessary to
adjust blade tension when the blade is removed and
replaced in only the upper blade holder as in performing
inside cutting operations. After desired tension is
obtained, position tension lever (A) in the horizontal
position, as shown in Fig. 7.
Fig. 7
Adjusting the blade for proper tension is usually
accomplished by trial and error. One method is to pull
back on the blade tension lever (A) Fig. 8, the blade
should start to have tension (resistance) when the blade
tension lever is half way between open Fig. 8, and closed
Fig. 7 positions. Finer blades require more tensioning
while thicker blades require less tension.
ADJUSTING CLAMPING
ACTION OF UPPER AND
LOWER BLADE HOLDER
CHUCK
A
Different widths of scroll saw blades will make it
necessary to adjust the clamping action of the upper and
lower blade holders. It should be noted, however, that
very little adjustment is necessary and very little
clamping force is required to hold the blade satisfactorily.
As a rule of thumb, looking down at the table with the
table insert slot in the 6 o’clock position, resistance on
the blade locking lever should be felt when the upper
blade locking lever reaches the 7 o’clock position, or
when the lower blade locking lever reaches the 5 o’clock
position.
Fig. 8
B
A
1. Move the blade locking lever (A) Fig. 9, to the rear
(open) position, as shown.
2. Turn chuck clamping knob (B) Fig. 9, clockwise to
tighten and counterclockwise to loosen the clamping
action of the blade holder chuck. Very little movement of
knob (B) will be necessary. NOTE: Only the upper chuck
is shown. Clamping action of the lower chuck is adjusted
in the same manner and can be accessed by removing
dust cup shown in Fig. 24.
Fig. 9
10
Download from Www.Somanuals.com. All Manuals Search And Download.
TILTING THE TABLE
The table on your scroll saw can be tilted 45° to the left
for bevel cutting operations by removing the dust cup as
shown in Fig. 24 and loosening table lock knob (A) Fig.
10, tilt the table to the desired angle indicated on degree
scale (B) Fig. 11 and tighten lock handle (A) Fig. 10.
When bevel cutting, the holddown (B) Fig. 12, can be
adjusted to lay flat on the stock by loosening screw (C)
and tilting the holddown (B). Then tighten screw (C).
A
Fig. 10
ADJUSTING THE TABLE
A
1. Loosen table lock knob as shown in Fig. 10 and
move the table all the way to the right until angle
indicator shown in Fig. 11 is on “0”.
B
2. Using a square that includes a level, check to see if
the table is level (A) Fig. 13, and is 90° to the saw blade
(B), as shown.
Fig. 11
3. If the table is not at 90° to the blade, adjust the table
making certain screw (B) Fig. 14, contacts bottom of
table surface when table is 90° to the blade. To make
this adjustment loosen nut (C), turn screw (B) in or out
the desired distance and tighten nut (C).
Note: After adjusting table, reposition the pointer (B) Fig.
11 to "0" degrees. Loosen the screw (A) Fig. 11 and
adjust pointer (B) to “0” degree mark and retighten
screw (A).
C
B
Fig. 12
B
B
C
A
Fig. 13
Fig. 14
11
Download from Www.Somanuals.com. All Manuals Search And Download.
ADJUSTING HOLDDOWN
The holddown (A) Fig. 15, should be adjusted so it
contacts the top surface of the work (D) being cut.
Loosen lock knob (B) and move holddown rod (C) up or
down, then tighten lock knob (B). The holddown (A) Fig.
15, may be adjusted front to rear, by loosening set screw
(B) Fig. 16, and positioning the holddown in the desired
location. Once the holddown is in the desired location,
tighten set screw (B), Fig. 16.
B
C
A
D
Fig. 15
ADJUSTING DUST BLOWER
The dust blower (A) Fig. 16, may be positioned to direct
air to the most effective point on the workpiece.
B
A
Fig. 16
DUST COLLECTION CUP
A dust collection cup (A) Fig. 17 is provided and can be
attached to a vacuum system by utilizing the port
covered by cap (B).
A
B
Fig. 17
12
Download from Www.Somanuals.com. All Manuals Search And Download.
TABLE INSERT
DISCONNECT MACHINE FROM POWER
SOURCE.
The table insert (A) can be positioned in the saw table with
the opening in the insert pointing to the front of the table,
as shown in Fig. 18, or to the right as shown in Fig. 19.
A
With the table in the level position, 90° to the blade, the
insert (A) should be positioned, as shown in Fig. 18. This
allows for the blade to be pivoted forward after it is
unclamped from the top blade holder, enabling you to
quickly insert the blade into the next hole in a pattern
when doing inside-cutting, as you will see later in this
manual.
Fig. 18
When tilting the table for bevel cutting operations the
insert (A) should be positioned as shown in Fig. 19. This
allows for clearance of the blade when tilting the table.
A blank table insert (B) Fig. 20, is supplied as standard
equipment with your scroll saw and can be used when
cutting very small workpieces to give added support to
the bottom of the workpiece. Cut a slot into the blank
and replace the standard insert (A) with the blank (B). The
slot cut into the blank (B) will only be as wide as the
blade giving maximum support to the bottom of the
workpiece. Adhesive backed spacer pads (C) are also
supplied for adjusting the table insert height relative to
the table surface. Place three pads an equal distance
apart on a cleaned surface to be applied to the blank
insert. Pads can be stacked in order to achieve desired
insert height.
A
Fig. 19
A
B
C
Fig. 20
13
Download from Www.Somanuals.com. All Manuals Search And Download.
OPERATIONS
FOLLOWING A LINE
With your scroll saw you should be able to perform straight or curved cuts with ease. Most beginners will experience
blade wandering; however, they eventually learn to control it as they become more familiar with the machine. Use scrap
material to practice cuts before starting a project. This enables you to develop your own style of cutting and you will
discover what you can do with your saw.
Always hold the work firmly against the table and do not feed the workpiece too fast while cutting. Feed the workpiece
only fast enough so that the blade will cut. Scroll saws cut faster across the grain than they do with the grain. Allow
for this tendency when cutting patterns that shift rather quickly from with-the-grain cuts to cross-grain cuts.
Make "relief" cuts before cutting long curves and never attempt to cut a curve that is too tight for the blade being used.
INSIDE CUTTING
Inside cutting takes place when the blade is threaded
through a hole in the workpiece. With your Delta 16”
C
Scroll Saw, you can perform this operation quickly and
easily as follows:
A
Loosen lock handle (A) Fig. 21, and raise the holddown
(B). Release blade tension by moving the blade tension
lever (C) to the horizontal position as previously
explained. Release upper blade holder lever (D) as
previously explained. This will release the blade (E) and
allow you to thread the blade through the next hole in
the pattern. Replace blade in upper blade holder and
move blade tension lever to the vertical position to re-
apply blade tension. Lower holddown and you are ready
to make the next cut.
D
E
B
Fig. 21
TROUBLE SHOOTING
CHOICE OF BLADE AND SPEED
Your scroll saw will accept a wide variety of 5" flat end blades and can be operated at any speed from 600 to 1650
cutting strokes per minute. Consider the following as a general guideline for selecting a blade and operating speed.
1. Use a finer blade for cutting thin workpieces, for hard materials, or when a smooth cut is required.
2. Use a coarser blade for cutting thick workpieces, when making straight cuts or for medium to soft materials.
3. Use a blade that will have 2 teeth in the workpiece at all times.
4. Most blade packaging is marked with the size of the wood the blade is intended to cut and the minimum radius
which can be cut with that blade.
5. Slower speeds are generally more effective than faster speeds when using thin blades and making intricate cuts.
6. Always start at a slow speed and gradually increase the speed until the best cutting speed is obtained.
BLADE BREAKAGE
Blade breakage is usually caused by one or more of the following:
1. Bending the blade during installation.
2. Improper blade tension.
3. Improper blade selection for the work being cut.
4. Forcing the work into the blade too rapidly.
5. Cutting too sharp a turn for the blade being used.
6. Improper blade speed.
14
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
CHANGING BLADES
DISCONNECT MACHINE FROM POWER
SOURCE.
B
1. Remove table insert (A) Fig. 22, and release blade
tension by pulling tension lever (B) forward, as shown.
A
Fig. 22
2. Push upper blade chuck locking lever (C) Fig. 23, to
the rear as shown. This will release the blade (D) from
the upper chuck (E).
E
C
D
Fig. 23
3. Remove the dust collection cup (A) by rotating knob
(B) 90° as shown in Fig. 24. Slide dust cup out of the
guides (C) by pulling it toward the front. NOTE: DO NOT
OPERATE THE UNIT WITH THE DUST CUP
REMOVED.
B
A
Fig. 24
15
Download from Www.Somanuals.com. All Manuals Search And Download.
4. Push lower blade chuck locking lever (F) Fig. 25, to
the rear as shown. This will release the blade (G) from
the lower chuck (H).
G
H
F
Fig. 25
5. Insert new blade (I) Fig. 26, into the upper blade
holder (J) making certain the blade teeth are pointing
down toward the table. Push upper blade chuck locking
lever (L) to the front. Insert new blade into the lower
blade holder Fig. 25 in the same manner.
J
6. Apply blade tension by referring to the following
section “ADJUSTING BLADE TENSION.”
I
L
Fig. 26
FUSE REPLACEMENT
A fuse holder (A) Fig. 27, and fuse (B) are located at the
rear of the machine and should be removed and
checked if the machine does not operate. If the fuse (B)
is bad, replace it with a 3 amp fast blow fuse.
B
A
Fig. 27
16
Download from Www.Somanuals.com. All Manuals Search And Download.
LUBRICATION
Perform maintenance below after each 20 hours of use.
DISCONNECT MACHINE FROM POWER
SOURCE.
1. Tilt the table 45° to the left as shown in Fig. 28.
2. Remove four rubber grommets (A) Fig. 29 that cover
the lubrication access holes.
3. Lubricate the pivot points in each of the four access
holes with a few drops of light machine oil.
4. Reassemble the four grommets as shown in Fig. 29.
Fig. 28
5. Apply lightweight grease or anti-seize to lubricate
the tensioning lever (C) Fig. 21 where it pivots on the
upper chuck.
A
Fig. 29
ACCESSORIES
A complete line of accessories is available from your Delta Supplier, Porter-Cable • Delta Factory Service Centers,
and Delta Authorized Service Stations. Please visit our Web Site www.deltamachinery.com for a catalog or
for the name of your nearest supplier.
Since accessories other than those offered by Delta have not been tested with this
product, use of such accessories could be hazardous. For safest operation, only Delta
recommended accessories should be used with this product.
PARTS, SERVICE OR WARRANTY ASSISTANCE
All Delta Machines and accessories are manufactured to high quality standards and are serviced by a network
of Porter-Cable • Delta Factory Service Centers and Delta Authorized Service Stations. To obtain additional
information regarding your Delta quality product or to obtain parts, service, warranty assistance, or the location
of the nearest service outlet, please call 1-800-223-7278 (In Canada call 1-800-463-3582).
17
Download from Www.Somanuals.com. All Manuals Search And Download.
Two Year Limited New Product Warranty
Delta will repair or replace, at its expense and at its option, any new Delta machine, machine part, or machine accessory
which in normal use has proven to be defective in workmanship or material, provided that the customer returns the product
prepaid to a Delta factory service center or authorized service station with proof of purchase of the product within two
years and provides Delta with reasonable opportunity to verify the alleged defect by inspection. For all refurbished Delta
product, the warranty period is 180 days. Delta may require that electric motors be returned prepaid to a motor
manufacturer’s authorized station for inspection and repair or replacement. Delta will not be responsible for any asserted
defect which has resulted from normal wear, misuse, abuse or repair or alteration made or specifically authorized by
anyone other than an authorized Delta service facility or representative. Under no circumstances will Delta be liable for
incidental or consequential damages resulting from defective products. This warranty is Delta’s sole warranty and sets
forth the customer’s exclusive remedy, with respect to defective products; all other warranties, express or implied, whether
of merchantability, fitness for purpose, or otherwise, are expressly disclaimed by Delta.
18
Download from Www.Somanuals.com. All Manuals Search And Download.
PORTER-CABLE • DELTA SERVICE CENTERS
(CENTROS DE SERVICIO DE PORTER-CABLE • DELTA)
Parts and Repair Service for Porter-Cable
(Obtenga Refaccion de Partes o Servicio para su Herramienta en los Siguientes Centros de Porter-Cable
•
Delta Machinery are Available at These Locations
•
Delta)
Cleveland 44125
ARIZONA
MINNESOTA
ILLINOIS
Minneapolis 55429
8001 Sweet Valley Drive
Unit #19
Tempe 85282 (Phoenix)
2400 West Southern Avenue
Suite 105
Addison 60101 (Chicago)
400 South Rohlwing Rd.
Phone: (630) 424-8805
Fax: (630) 424-8895
5522 Lakeland Avenue North
Phone: (763) 561-9080
Fax: (763) 561-0653
Phone: (216) 447-9030
Fax: (216) 447-3097
Phone: (602) 437-1200
Fax: (602) 437-2200
Woodridge 60517 (Chicago)
2033 West 75th Street
Phone: (630) 910-9200
Fax: (630) 910-0360
MISSOURI
OREGON
Portland 97230
4916 NE 122 nd Ave.
Phone: (503) 252-0107
Fax: (503) 252-2123
CALIFORNIA
North Kansas City 64116
1141 Swift Avenue
Phone: (816) 221-2070
Fax: (816) 221-2897
Ontario 91761 (Los Angeles)
3949A East Guasti Road
Phone: (909) 390-5555
Fax: (909) 390-5554
MARYLAND
St. Louis 63119
Elkridge 21075 (Baltimore)
7397-102 Washington Blvd.
Phone: (410) 799-9394
Fax: (410) 799-9398
San Leandro 94577 (Oakland)
3039 Teagarden Street
Phone: (510) 357-9762
Fax: (510) 357-7939
7574 Watson Road
Phone: (314) 968-8950
Fax: (314) 968-2790
PENNSYLVANIA
Willow Grove 19090
520 North York Road
Phone: (215) 658-1430
Fax: (215) 658-1433
NEW YORK
COLORADO
MASSACHUSETTS
Arvada 80003 (Denver)
8175 Sheridan Blvd., Unit S
Phone: (303) 487-1809
Fax: (303) 487-1868
Flushing 11365-1595 (N.Y.C.)
175-25 Horace Harding Expwy.
Phone: (718) 225-2040
Fax: (718) 423-9619
Braintree 02185 (Boston)
719 Granite Street
Phone: (781) 848-9810
Fax: (781) 848-6759
Franklin 02038 (Boston)
Franklin Industrial Park
101E Constitution Blvd.
Phone: (508) 520-8802
Fax: (508) 528-8089
TEXAS
Carrollton 75006 (Dallas)
1300 Interstate 35 N, Suite 112
Phone: (972) 446-2996
Fax: (972) 446-8157
FLORIDA
Davie 33314 (Miami)
4343 South State Rd. 7 (441)
Unit #107
NORTH CAROLINA
Charlotte 28270
9129 Monroe Road, Suite 115
Phone: (704) 841-1176
Fax: (704) 708-4625
Houston 77038
Phone: (954) 321-6635
Fax: (954) 321-6638
4321 Sam Houston Parkway,
West
Suite 180
Tampa 33609
Phone: (281) 260-8887
Fax: (281) 260-9989
4538 W. Kennedy Boulevard
Phone: (813) 877-9585
Fax: (813) 289-7948
OHIO
WASHINGTON
MICHIGAN
Columbus 43214
4560 Indianola Avenue
Phone: (614) 263-0929
Fax: (614) 263-1238
Auburn 98001(Seattle)
3320 West Valley HWY, North
Building D, Suite 111
Phone: (253) 333-8353
Fax: (253) 333-9613
Madison Heights 48071 (Detroit)
30475 Stephenson Highway
Phone: (248) 597-5000
GEORGIA
Forest Park 30297 (Atlanta)
5442 Frontage Road,
Suite 112
Fax: (248) 597-5004
Phone: (404) 608-0006
Fax: (404) 608-1123
Authorized Service Stations are located in many large cities. Telephone 800-438-2486 or 731-541-6042 for assistance locating one.
Parts and accessories for Porter-Cable·Delta products should be obtained by contacting any Porter-Cable·Delta Distributor, Authorized
Service Center, or Porter-Cable·Delta Factory Service Center. If you do not have access to any of these, call 800-223-7278 and you will
be directed to the nearest Porter-Cable·Delta Factory Service Center. Las Estaciones de Servicio Autorizadas están ubicadas en muchas
grandes ciudades. Llame al 800-438-2486 ó al 731-541-6042 para obtener asistencia a fin de localizar una. Las piezas y los accesorios
para los productos Porter-Cable·Delta deben obtenerse poniéndose en contacto con cualquier distribuidor Porter-Cable·Delta, Centro
de Servicio Autorizado o Centro de Servicio de Fábrica Porter-Cable·Delta. Si no tiene acceso a ninguna de estas opciones, llame al
800-223-7278 y le dirigirán al Centro de Servicio de Fábrica Porter-Cable·Delta más cercano.
CANADIAN PORTER-CABLE • DELTA SERVICE CENTERS
ALBERTA
QUÉBEC
MANITOBA
Bay 6, 2520-23rd St. N.E.
Calgary, Alberta
T2E 8L2
1515 ave.
1699 Dublin Avenue
Winnipeg, Manitoba
R3H 0H2
St-Jean Baptiste, Suite 160
Québec, Québec
G2E 5E2
Phone: (418) 877-7112
Fax: (418) 877-7123
Phone: (403) 735-6166
Fax: (403) 735-6144
Phone: (204) 633-9259
Fax: (204) 632-1976
ONTARIO
BRITISH COLUMBIA
8520 Baxter Place
Burnaby, B.C.
1447, Begin
505 Southgate Drive
Guelph, Ontario
N1H 6M7
St-Laurent, (Montréal),
Québec
V5A 4T8
H4R 1V8
Phone: (519) 767-4132
Fax: (519) 767-4131
Phone: (604) 420-0102
Fax: (604) 420-3522
Phone: (514) 336-8772
Fax: (514) 336-3505
The following are trademarks of PORTER-CABLE·
DELTA (Las siguientes son marcas registradas de PORTER-CABLE S.A.): Auto-Set®,
BAMMER®, B.O.S.S.®, Builder’s Saw®, Contractor’s Saw®, Contractor’s Saw II™, Delta®, DELTACRAFT®, DELTAGRAM™, Delta Series
2000™, DURATRONIC™, Emc²™, FLEX®, Flying Chips™, FRAME SAW®, Homecraft®, INNOVATION THAT WORKS®, Jet-Lock®,
JETSTREAM®, ‘kickstand®, LASERLOC®, MICRO-SET®, Micro-Set®, MIDI LATHE®, MORTEN™, NETWORK™, OMNIJIG®, POCKET
CUTTER®, PORTA-BAND®, PORTA-PLANE®, PORTER-CABLE®&(design), PORTER-CABLE®PROFESSIONAL POWER TOOLS, Posi-Matic®,
Q-3®&(design), QUICKSAND®&(design), QUICKSET™, QUICKSET II®, QUICKSET PLUS™, RIPTIDE™&(design), SAFE GUARD II®, SAFE-
LOC®, Sanding Center®, SANDTRAP®&(design), SAW BOSS®, Sawbuck™, Sidekick®, SPEED-BLOC®, SPEEDMATIC®, SPEEDTRONIC®,
STAIR EASE®, The American Woodshop®&(design), The Lumber Company®&(design), THE PROFESSIONAL EDGE®, THE PROFESSIONAL
SELECT®, THIN-LINE™, TIGER®, TIGER CUB®, TIGER SAW®, TORQBUSTER®, TORQ-BUSTER®, TRU-MATCH™, TWIN-LITE®,
UNIGUARD®, Unifence®, UNIFEEDER™, Unihead®, Uniplane™, Unirip®, Unisaw®, Univise®, Versa-Feeder®, VERSA-PLANE® , WHISPER
SERIES®, WOODWORKER’S CHOICE™.
Trademarks noted with ™ and ® are registered in the United States Patent and Trademark Office and may also be registered in other
countries. Las Marcas Registradas con el signo de ™ y ® son registradas por la Oficina de Registros y Patentes de los Estados Unidos y
también pueden estar registradas en otros países.
Printed in U.S.A.
PC-0603-149
Download from Www.Somanuals.com. All Manuals Search And Download.
|