HigH REACH ROPE
CHAin sAw
Model 97092
sEt uP And OPERAting instRuCtiOns
Diagrams within this manual may not be drawn proportionally.
Due to continuing improvements, actual product may differ slightly from the product described herein.
®
distributed exclusively by Harbor Freight tools .
3491 Mission Oaks Blvd., Camarillo, CA 93011
Visit our website at: http://www.harborfreight.com
Read this material before using this product.
Failure to do so can result in serious injury.
sAVE tHis MAnuAl.
©
®
Copyright 2007 by Harbor Freight Tools . All rights reserved. No portion of
this manual or any artwork contained herein may be reproduced in any shape
or form without the express written consent of Harbor Freight Tools.
For technical questions or replacement parts, please call 1-800-444-3353.
Keep this manual for the safety warnings and precautions, assembly, operating,
inspection, maintenance and cleaning procedures. Write the product’s serial number
in the back of the manual near the assembly diagram (or month and year of purchase if
product has no number). Keep this manual and the receipt in a safe and dry place for
future reference.
general safety Rules
wARning! Read all instructions
Failure to follow all instructions listed below may result in serious injury.
1.
2.
Keep work area clean and well lit. Cluttered or dark areas invite accidents.
Keep children and bystanders away while operating a Chain saw. Distrac-
tions can cause you to lose control.
3.
Stay alert, watch what you are doing and use common sense when operating a
Chain Saw. Do not use this product while you are tired or under the influence
of drugs, alcohol or medication. A moment of inattention while operating Chain
Saws may result in serious personal injury.
4.
use safety equipment. Always wear eye protection. Safety equipment
such as dust mask, non-skid safety shoes, ANSI approved hard hat, full
face shield, and work gloves should be used for appropriate conditions to
reduce personal injuries.
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Do not overreach. Keep proper footing and balance at all times. Do not use this
product on a ladder. This enables better control of the Chain Saw in unexpected
situations.
6.
store idle Chain saws out of the reach of children and do not allow per-
sons unfamiliar with the tool or these instructions to operate it.
7.
Keep cutting tools sharp and clean. Properly maintained cutting tools with sharp
cutting edges are less likely to bind and are easier to control.
8.
Always stand to one side and cut at a 45° angle to avoid falling debris. Do not
cut directly overhead.
9.
Do not use near utility lines. Plan ahead and clear the area beneath branches
being cut to avoid property damage or injury.
10.
Only use the Chain saw to cut tree limbs and roots that have a diameter
less than 3”.
11.
12.
This product is not a toy. Keep it out of reach of children.
The warnings, precautions, and instructions discussed in this instruction manual
cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which
cannot be built into this product, but must be supplied by the operator.
sAVE tHEsE instRuCtiOns.
unPACKing
When unpacking, check to make sure that the item is intact and undamaged. If
any parts are missing or broken, please call Harbor Freight Tools at the number shown
on the cover of this manual as soon as possible.
OPERAting instRuCtiOns
Read the EntiRE iMPORtAnt sAFEty inFORMAtiOn section at the
beginning of this manual including all text under subheadings therein
before set up or use of this product.
1.
Shake both Extension Ropes (2) out and remove any tangles or knots. Straight-
en the Chain Saw (3) and ensure that there are no kinks in it.
2.
3.
Throw the Extension Rope with the weight over the branch that needs to be cut.
Use the hooks to connect the Chain Saw to the end of the weighed rope. Hook
the other Extension Rope to the other end of the Chain Saw and pull the chain
up so that it engages the branch.
4.
Position the Chain Saw as close to where the branch meets the tree as possible.
SKU 97092
For technical questions, please call 1-800-444-3353.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
5.
Move as far away from the cutting area as the Extension Ropes allows. Con-
nect the Handles (1) to the ends of the Extension Ropes. Longer ropes of the
same gauge as the Extension Ropes can be attached to the Chain Saw so that
higher limbs can be cut and/or the user can be a safe distance away from the
limb being cut.
6.
7.
8.
Cut at a 45° angle by pulling the Extension Ropes alternately with each hand.
As the Chain is pulled it will automatically orient itself to cut the limb.
Cutting the bottom of the branch first will prevent the limb from peeling excess
amounts of bark from the tree when the limb falls.
Saw the limb in long, brisk strokes. Use the full length of the Chain Saw to cut
the limb. Do not change position while cutting as this can cause the Chain to
bind. Stay clear of the cutting area for safety.
9.
To cut roots, clear away dirt and debris from around the root, loop the Chain
Saw under the root, connect the Handles, and pull back and forth until the root is
sawed through. Cut the root at a 45° angle, repeat at the other side of the root
to remove it completely.
Caution. Do not put excess pressure on the Chain Saw during this process or, when
the root is cut through, the Saw could fly back toward the operator, possibly
causing personal injury.
10.
Removing branches or roots can be traumatic to the tree and can provide an
entry point for disease and pests. Seek advice from your local lawn and garden
specialist concerning care for the tree after limb removal.
11.
Clean, then store the tool indoors out of children’s reach.
SKU 97092
For technical questions, please call 1-800-444-3353.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
MAintEnAnCE And sERViCing
damaged equipment can fail, causing serious personal
injury. do not use damaged equipment.
wARning
1.
BEFORE EACH usE, inspect the general condition of the tool. Check for loose
fittings, frayed ropes, cracked or broken parts and any other condition that may
affect its safe operation.
2.
3.
Have Chain Saw sharpened by a qualified service technician.
AFtER usE, clean external surfaces of the tool with clean, moist cloth. Apply
light machine oil before storage.
PlEAsE REAd tHE FOllOwing CAREFully
THE MANUFACTURER AND/OR DISTRIBUTOR HAS PROvIDED THE PARTS LIST AND
ASSEMBLy DIAgRAM IN THIS MANUAL AS A REFERENCE TOOL ONLy. NEITHER THE
MANUFACTURER OR DISTRIBUTOR MAKES ANy REPRESENTATION OR WARRANTy
OF ANy KIND TO THE BUyER THAT HE OR SHE IS qUALIFIED TO MAKE ANy REPAIRS
TO THE PRODUCT, OR THAT HE OR SHE IS qUALIFIED TO REPLACE ANy PARTS OF
THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR ExPRESSLy
STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE UNDERTAKEN
By CERTIFIED AND LICENSED TECHNICIANS, AND NOT By THE BUyER. THE BUyER
ASSUMES ALL RISK AND LIABILITy ARISINg OUT OF HIS OR HER REPAIRS TO THE
ORIgINAL PRODUCT OR REPLACEMENT PARTS THERETO, OR ARISINg OUT OF HIS OR
HER INSTALLATION OF REPLACEMENT PARTS THERETO.
PARts list & AssEMBly diAgRAM
Part
1
description
Qty
2
Part
3
description
Chain Saw
Qty
1
Handle
2
Extension Rope
2
4
Storage Pouch (not shown)
1
2
3
1
SKU 97092
For technical questions, please call 1-800-444-3353.
Page 4
Download from Www.Somanuals.com. All Manuals Search And Download.
|