Operator’s manual (EPA III, CARB III)
Manual de instrucciones (EPA III, CARB III)
435 435e 440e
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
Lea detenidamente el manual de instrucciones y asegúrese de entender su contenido antes de utilizar la máquina.
English (2-44)
Spanish (45-87)
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY TO SYMBOLS
Symbols on the machine:
Symbols in the operator’s
WARNING! Chain saws can be
dangerous! Careless or improper use
can result in serious or fatal injury to the
operator or others.
manual:
Switch off the engine before
carrying out any checks or
maintenance. CAUTION! The
start/stop switch automatically
returns to run position. In order to
prevent unintentional starting, the
spark plug cap must be removed from the spark plug
when assembling, checking and/or performing
maintenance.
Please read the operator’s manual
carefully and make sure you
understand the instructions before
using the machine.
Always wear:
•
•
•
Approved protective helmet
Approved hearing protection
Protective goggles or a visor
Always wear approved protective
gloves.
Both of the operator′s hands must be
used to operate the chain saw.
Regular cleaning is required.
Visual check.
Never operate a chain saw holding it with
one hand only.
Contact of the guide bar tip with any
object must be avoided.
Tip contact may cause the guide bar to
move suddenly upward and backward (so-
called kickback), which may cause serious
injury.
Protective goggles or a visor must be
worn.
WARNING! Kickback may occur when
the nose or tip of the guide bar touches
an object, and cause a lightning fast
reverse reaction, kicking the guide bar
up and towards the operator. May cause
serious personal injury.
Refuelling.
Filling with oil and adjusting oil flow.
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
The chain brake must be engaged
when the chain saw is started.
WARNING! Kickback may occur when
the nose or tip of the guide bar touches
an object, and cause a lightning fast
reverse reaction, kicking the guide bar
up and towards the operator. May cause
serious personal injury.
2 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY TO SYMBOLS
You will find the following labels on your chain saw:
EPA III
The Emissions Compliance Period referred to on the
Emission Compliance label indicates the number of
operating hours for which the engine has been shown to
meet Federal emissions requirements.
Maintenance, replacement, or repair of the emission
control devices and system may be performed by any
nonroad engine repair establishment or individual.
The engine exhaust from this product
contains chemical known to the State
of California to cause cancer, birth
defects or other reproductive harm.
115 13 80-96 Rev.3 2008-12-17
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
FEDERAL AND CALIFORNIA EMISSIONS
CONTROL WARRANTY STATEMENT
Contents
KEY TO SYMBOLS
CONTENTS
AMERICAN STANDARD SAFETY
PRECAUTIONS
INTRODUCTION
WHAT IS WHAT?
What is what on the chain saw? ........................... 6
GENERAL SAFETY PRECAUTIONS
Important .............................................................. 7
ASSEMBLY
FUEL HANDLING
STARTING AND STOPPING
WORKING TECHNIQUES
MAINTENANCE
Checking, maintaining and servicing chain saw
TECHNICAL DATA
4 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear customer!
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Huskvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant. During over 300 years of continuous operation, the Husqvarna factory has produced a lot of different
products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first
motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working
today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. We develop, manufacture and market high quality motor driven products for forestry and gardening as
well as for building and construction industry.
Your purchase gives you access to professional help with repairs and service whenever this may be necessary. If the
retailer who sells your machine is not one of our authorized dealers, ask for the address of your nearest servicing dealer.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator′s manual as a valuable document. By following its′ content (using, service, maintenance etc) the life span and
the second-hand value of the machine can be extended.If you ever lend or sell this machine, make sure that the borrower
or buyer gets the operator′s manual, so they will also know how to properly maintain and use it.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
English – 5
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
What is what on the chain saw?
1
2
3
4
5
6
7
8
9
Cylinder cover
16 Muffler
17 Chain
Air purge
Start reminder
18 Bar tip sprocket
Combined start and stop switch
Rear handle
19 Bar
20 Bumper spike
21 Chain catcher
22 Chain tensioner wheel
23 Clutch cover
Information and warning decal
Fuel tank
Adjuster screws carburetor
Starter handle
24 Right hand guard
25 Throttle control
26 Throttle lockout
27 Knob
10 Starter
11 Chain oil tank
12 Product and serial number plate
13 Felling direction mark
14 Front handle
28 Operator’s manual (EPA)
29 Bar guard
15 Front hand guard
30 Combination spanner
6 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Before using a new chain saw
WARNING! Never allow children to use or
be in the vicinity of the machine. As the
machine is equipped with a spring-
loaded stop switch and can be started by
low speed and force on the starter
handle, even small children under some
circumstances can produce the force
necessary to start the machine.This can
mean a risk of serious personal injury.
Therefore remove the spark plug cap
when the machine is not under close
supervision.
•
Please read this manual carefully.
!
•
Check that the cutting equipment is correctly fitted and
adjusted. See instructions under the heading
Assembly.
•
•
•
Refuel and start the chain saw. See the instructions
under the headings Fuel Handling and Starting and
Stopping.
Do not use the chain saw until sufficient chain oil has
reached the chain.See instructions under the heading
Cutting equipment.
Long-term exposure to noise can result in permanent
hearing impairment. So always use approved hearing
protection.
Important
IMPORTANT!
The machine is only designed for cutting wood.
WARNING! Under no circumstances may
the design of the machine be modified
You should only use the saw with the bar and chain
combinations we recommend in the chapter Technical
data.
!
without the permission of the
manufacturer. Always use genuine
accessories. Non-authorized
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.Your
warranty may not cover damage or
liability caused by the use of non-
authorized accessories or replacement
parts.
Never use the machine if you are fatigued, while under
the influence of alcohol or drugs, medication or anything
that could affect your vision, alertness, coordination or
judgement.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
Do not modify this product or use it if it appears to have
been modified by others.
WARNING! A chain saw is a dangerous
tool if used carelessly or incorrectly and
can cause serious, even fatal injuries. It
is very important that you read and
understand the contents of this
operator’s manual.
Never use a machine that is faulty. Carry out the checks,
maintenance and service instructions described in this
manual. Some maintenance and service measures
must be carried out by trained and qualified specialists.
See instructions under the heading Maintenance.
!
Never use any accessories other than those
recommended in this manual. See instructions under
the headings Cutting equipment and Technical data.
WARNING! The inside of the muffler
contain chemicals that may be
carcinogenic. Avoid contact with these
elements in the event of a damaged
muffler.
!
CAUTION! Always wear protective glasses or a face
visor to reduce the risk of injury from thrown objects. A
chain saw is capable of throwing objects, such as wood
chips, small pieces of wood, etc, at great force.This can
result in serious injury, especially to the eyes.
WARNING! Long term inhalation of the
engine’s exhaust fumes, chain oil mist
and dust from sawdust can represent a
health risk.
!
WARNING! Running an engine in a
confined or badly ventilated area can
result in death due to asphyxiation or
carbon monoxide poisoning.
WARNING! The ignition system of this
machine produces an electromagnetic
!
WARNING! Faulty cutting equipment or
the wrong combination of bar and saw
chain increases the risk of kickback!
Only use the bar/saw chain combinations
we recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
field during operation.This field may
under some circumstances interfere with
pacemakers.To reduce the risk of
serious or fatal injury, we recommend
persons with pacemakers to consult
their physician and the pacemaker
manufacturer before operating this
machine.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 7
GENERAL SAFETY PRECAUTIONS
•
•
•
Gloves with saw protection
Always use common sense
Trousers with saw protection
It is not possible to cover every conceivable situation you
can face when using a chain saw. Always exercise care and
use your common sense. Avoid all situations which you
consider to be beyond your capability. If you still feel
uncertain about operating procedures after reading these
instructions, you should consult an expert before continuing.
Do not hesitate to contact your dealer or us if you have any
questions about the use of the chain saw.We will willingly be
of service and provide you with advice as well as help you to
use your chain saw both efficiently and safely. Attend a
training course in chain saw usage if possible.Your dealer,
forestry school or your library can provide information about
which training materials and courses are available.
Boots with saw protection, steel toe-cap and non-slip
sole
•
•
Always have a first aid kit nearby.
Fire Extinguisher and Shovel
Generally clothes should be close-fitting without
restricting your freedom of movement.
IMPORTANT! Sparks can come from the muffler, the bar
and chain or other sources. Always have fire
extinguishing tools available if you should need them.
Help prevent forest fires.
′
Machine s safety equipment
In this section the machine’s safety features and their
function are explained. For inspection and maintenance
see instructions under the heading Checking, maintaining
and servicing chain saw safety equipment. See
instructions under the heading, What is what?, to find
where these parts are located on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest servicing dealer.
Work is constantly in progress to improve the design and
technology - improvements that increase your safety and
efficiency. Visit your dealer regularly to see whether you
can benefit from new features that have been introduced.
WARNING! Never use a machine with
defective safety components. Safety
!
equipment must be inspected and
maintained. See instructions under the
heading Checking, maintaining and
servicing chain saw safety equipment. If
your machine does not pass all the
checks, take the saw to a servicing
dealer for repair.
Personal protective equipment
WARNING! Most chain saw accidents
happen when the chain touches the
!
operator.You must use approved
personal protective equipment whenever
you use the machine. Personal protective
equipment cannot eliminate the risk of
injury but it will reduce the degree of
injury if an accident does happen. Ask
your dealer for help in choosing the right
equipment.
Chain brake and front hand guard
Your chain saw is equipped with a chain brake that is
designed to stop the chain if you get a kickback.The chain
brake reduces the risk of accidents, but only you can
prevent them.
Take care when using your saw and make sure the
kickback zone of the bar never touches any object.
•
•
•
Approved protective helmet
Hearing protection
Protective goggles or a visor
8 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
•
The chain brake (A) can either be activated manually
(by your left hand) or automatically by the inertia
release mechanism.
•
The chain brake is released by moving the front hand
guard marked ”PULL BACK TO RESET” back,
towards the front handle.
The brake is applied when the front hand guard (B) is
pushed forwards.
•
Kickback can be very sudden and violent. Most
kickbacks are minor and do not always activate the
chain brake. If this happens you should hold the chain
saw firmly and not let go.
•
This movement activates a spring-loaded mechanism
that tightens the brake band (C) around the engine
drive system (D) (clutch drum).
•
The way the chain brake is activated, either manually
or automatically by the inertia release mechanism,
depends on the force of the kickback and the position
of the chain saw in relation to the object that the
kickback zone of the bar strikes.
•
The front hand guard is not designed solely to activate
the chain brake. Another important feature is that it
reduces the risk of your left hand hitting the chain if
you lose grip of the front handle.
If you get a violent kickback while the kickback zone of
the bar is farthest away from you the chain brake is
designed to be activated by the inertia in the kickback
direction.
•
The chain brake must be engaged when the chain
saw is started to prevent the saw chain from rotating.
•
Use the chain brake as a ”parking brake”when starting
and when moving over short distances, to reduce the
risk of moving chain accidentally hitting your leg or
anyone or anything close by. Do not leave the chain
saw switched on with the chain brake activated for long
periods. The chain saw can become very hot.
If the kickback is less violent or the kickback zone of
the bar is closer to you the chain brake is designed to
be activated manually by the movement of your left
hand.
•
In the felling position the left hand is in a position that
makes manual activation of the chain brake
impossible. With this type of grip, that is when the left
hand is placed so that it cannot affect the movement
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 9
GENERAL SAFETY PRECAUTIONS
of the front hand guard, the chain brake can only be
activated by the inertia action.
Throttle lockout
The throttle lockout is designed to prevent accidental
operation of the throttle control. When you press the lock
(A) (i.e.when you grasp the handle) it releases the throttle
control (B). When you release the handle the throttle
control and the throttle lockout both move back to their
original positions. This arrangement means that the
throttle control is automatically locked at the idle setting.
Will my hand always activate the chain
brake during a kickback?
No. It takes a certain force to move the hand guard
forward. If your hand only lightly touches the front guard
or slips over it, the force may not be enough to trigger the
chain brake.You should also maintain a firm grip of the
chain saw handles while working. If you do and
experience a kickback, your hand may never leave the
front handle and will not activate the chain brake, or the
chain brake will only activate after the saw has swung
around a considerable distance. In such instances, the
chain brake might not have enough time to stop the saw
chain before it touches you.
Chain catcher
The chain catcher is designed to catch the chain if it snaps
or jumps off. This should not happen if the chain is
properly tensioned (see instructions under the heading
Assembly) and if the bar and chain are properly serviced
and maintained (see instructions under the heading
General working instructions).
There are also certain positions in which your hand
cannot reach the front hand guard to activate the chain
brake; for example, when the saw chain is held in felling
position.
Will my inertia activated chain brake
always activate during kickback in the
event of a kickback?
No. First your brake must be in working order.Testing the
brake is simple, see instructions under the heading
Checking, maintaining and servicing chain saw safety
equipment.We recommend you do before you begin each
work session. Second the kickback must be strong
enough to activate the chain brake. If the chain brake is
too sensitive it would activate all the time which would be
a nuisance.
Right hand guard
Apart from protecting your hand if the chain jumps or
snaps, the right hand guard stops branches and twigs
from interfering with your grip on the rear handle.
Will my chain brake always protect me
from injury in the event of a kickback?
No. First, the chain brake must be in working order to
provide the intended protection. Second, it must be
activated during the kickback as described above to stop
the saw chain.Third, the chain brake may be activated but
if the bar is too close to you the brake might not have
enough time to slow down and stop the chain before the
chain saw hits you.
Only you and proper working technique can eliminate
kickback and its danger.
10 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Vibration damping system
Muffler
Your machine is equipped with a vibration damping
system that is designed to reduce vibration and make
operation easier.
The muffler is designed to keep noise levels to a minimum
and to direct exhaust fumes away from the user.
WARNING! The exhaust fumes from the
engine are hot and may contain sparks
!
which can start a fire. Never start the
machine indoors or near combustible
material!
The machine′s vibration damping system reduces the
transfer of vibration between the engine unit/cutting
equipment and the machine′s handle unit.The body of the
chain saw, including the cutting equipment, is insulated
from the handles by vibration damping units.
In areas with a hot, dry climate there is a high risk of fires.
These areas are sometimes subject to government rules
requiring among other things the muffler must be
equipped with an approved type of spark arrestor screen.
Cutting hardwoods (most broadleaf trees) creates more
vibration than cutting softwoods (most conifers). Cutting
with cutting equipment that is blunt or faulty (wrong type
or badly sharpened) will increase the vibration level.
When fitting the mesh, make sure that the mesh is
inserted in the right position. If necessary, use the
combination spanner to insert or remove the mesh.
CAUTION! The muffler gets very hot during and after
use.This also applies during idling. Be aware of the fire
hazard, especially when working near flammable
substances and/or vapours.
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
!
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition.These
symptoms normally appear in the
fingers, hands or wrists.These
WARNING! Never use a saw without a
muffler, or with a damaged muffler. A
!
damaged muffler may substantially
increase the noise level and the fire
hazard. Keep fire fighting equipment
handy. If a spark arrestor screen is
required in your area, never use the saw
without or with a broken spark arrestor
screen.
symptoms may be increased in cold
temperatures.
Cutting equipment
Stop switch
Use the stop switch to switch off the engine.
This section describes how to choose and maintain your
cutting equipment in order to:
•
•
Reduce the risk of kickback.
Reduce the risk of the saw chain breaking or jumping
off the bar.
•
•
•
Obtain optimal cutting performance.
Extend the life of cutting equipment.
Avoid increasing vibration levels.
115 13 80-96 Rev.3 2008-12-17
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
General rules
Cutting equipment designed to reduce
kickback
•
Only use cutting equipment recommended by us!
See instructions under the heading Technical data.
WARNING! Faulty cutting equipment or
the wrong combination of bar and saw
chain increases the risk of kickback!
Only use the bar/saw chain combinations
we recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
!
•
Keep the chain’s cutting teeth properly
sharpened! Follow our instructions and use the
recommended file gauge. A damaged or badly
sharpened chain increases the risk of accidents.
The only way to avoid kickback is to make sure that the
kickback zone of the bar never touches anything.
By using cutting equipment with ”built-in” kickback
reduction and keeping the chain sharp and well-
maintained you can reduce the effects of kickback.
Bar
•
Maintain the correct depth gauge setting! Follow
our instructions and use the recommended depth
gauge clearance. Too large a clearance increases
the risk of kickback.
The smaller the tip radius the lower the chance of
kickback.
Chain
A chain is made up of a number of links, which are
available in standard and low-kickback versions.
IMPORTANT! No saw chain design eliminates the
danger of kickback.
•
•
Keep the chain properly tensioned! If the chain is
slack it is more likely to jump off and lead to increased
wear on the bar, chain and drive sprocket.
WARNING! Any contact with a rotating
saw chain can cause extremely serious
injuries.
!
Some terms that describe the bar and chain
To maintain the safety features of the cutting equipment,
you should replace a worn or damaged bar or chain with
a bar and chain combinations recommended by
Husqvarna. See instructions under the heading Technical
Data for a list of replacement bar and chain combinations
we recommend.
Keep cutting equipment well lubricated and
properly maintained! A poorly lubricated chain is
more likely to break and lead to increased wear on the
bar, chain and drive sprocket.
Bar
•
Length (inches/cm)
•
Number of teeth on bar tip sprocket (T).
•
Chain pitch (inches). The spacing between the drive
links of the chain must match the spacing of the teeth
on the bar tip sprocket and drive sprocket.
12 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
Number of drive links. The number of drive links is
determined by the length of the bar, the chain pitch
and the number of teeth on the bar tip sprocket.
•
A sharp chain eats its way through the wood and
produces long, thick chips or shavings.
•
Bar groove width (inches/mm). The groove in the bar
must match the width of the chain drive links.
•
The cutting part of the chain is called the cutter and
consists of a cutting tooth (A) and the depth gauge (B).
The cutters cutting depth is determined by the difference
in height between the two (depth gauge setting).
When you sharpen a cutting tooth there are four important
factors to remember.
•
Chain oil hole and hole for chain tensioner. The bar
must be matched to the chain saw design.
1
Filing angle
Chain
2
Cutting angle
•
Chain pitch (inches)
3
4
File position
•
Drive link width (mm/inches)
Round file diameter
•
Number of drive links.
It is very difficult to sharpen a chain correctly without the
right equipment. We recommend that you use our file
gauge. This will help you obtain the maximum kickback
reduction and cutting performance from your chain.
Sharpening your chain and adjusting
depth gauge setting
General information on sharpening cutting teeth
•
Never use a blunt chain. When the chain is blunt you
have to exert more pressure to force the bar through
the wood and the chips will be very small. If the chain
is very blunt it will produce wood powder and no chips
or shavings.
See instructions under the heading Technical data for
information about sharpening your chain.
WARNING! Departure from the
sharpening instructions considerably
increases the risk of kickback.
!
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 13
GENERAL SAFETY PRECAUTIONS
Sharpening cutting teeth
Adjustment of depth gauge setting
To sharpen cutting teeth you will need a round file and a
file gauge. See instructions under the heading Technical
data for information on the size of file and gauge that are
recommended for the chain fitted to your chain saw.
•
•
The cutting teeth should be newly sharpened before
adjusting the depth gauge setting. We recommend
that you adjust the depth gauge setting every third
time you sharpen the cutting teeth. NOTE! This
recommendation assumes that the length of the
cutting teeth is not reduced excessively.
You will need a flat file and a depth gauge tool. We
recommend that you use our depth gauge tool to
acheive the correct depth gauge setting and bevel for
the depth gauge.
•
•
Check that the chain is correctly tensioned. A slack
chain will move sideways, making it more difficult to
sharpen correctly.
•
Place the depth gauge tool over the chain. Detailed
information regarding the use of the depth gauge tool,
will be found on the package for the depth gauge tool.
Use the flat file to file off the tip of the depth gauge that
protrudes through the depth gauge tool. The depth
gauge setting is correct when you no longer feel
resistance as you draw the file along the depth gauge
tool.
Always file cutting teeth from the inside face. Reduce
the pressure on the return stroke. File all the teeth on
one side first, then turn the chain saw and file the teeth
on the other side.
•
File all the teeth to the same length. When the length
of the cutting teeth is reduced to 0.16 inch (4 mm) the
chain is worn out and should be replaced.
Tensioning the chain
WARNING! A slack chain may jump off
the bar and cause serious or even fatal
injury.
General advice on adjusting depth gauge setting
!
•
When you sharpen the cutting tooth (A) the depth
gauge setting (C) will decrease. To maintain optimal
cutting performance the depth gauge (B) has to be
filed down to achieve the recommended depth gauge
setting. See instructions under the heading Technical
data to find the correct depth gauge setting for your
particular chain.
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up
the slack.
Check the chain tension every time you refuel. NOTE! A
new chain has a running-in period during which you
should check the tension more frequently.
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand.
WARNING! The risk of kickback is
increased if the depth gauge setting is
too large!
!
14 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
435
•
Turn the knob anti clockwise to loosen the bar cover.
•
Loosen the bar nut that holds the clutch cover and
chain brake. Use the combination spanner. Then
retighten the bar nut as tightly as you can by hand.
•
Adjust the tension on the chain by turning the wheel
down (+) for tighter tension and up (-) to loosen the
tension.
•
Raise the tip of the bar and stretch the chain by
tightening the chain tensioning screw using the
combination spanner. Tighten the chain until it does
not sag from the underside of the bar.
•
Use the combination spanner to tighten the bar nut
while holding up the tip of the bar. Check that you can
pull the saw chain round freely by hand, and that there
is no slack on the underside of the bar.
•
Tighten the bar clutch by turning the knob clockwise.
The position of the chain tensioning screw on our chain
saws varies from model to model. See instructions under
the heading What is what? to find out where it is on your
model.
435e, 440e
•
Fold the knob back in to lock the tensioning.
•
Release the knob by folding it out.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 15
GENERAL SAFETY PRECAUTIONS
Checking chain lubrication
Lubricating cutting equipment
•
Check the chain lubrication each time you refuel. See
instructions under the heading Lubricating the bar tip
sprocket.
WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.
!
Aim the tip of the bar at a light coloured surface about
20 cm (8 inches) away. After 1 minute running at 3/4
throttle you should see a distinct line of oil on the light
surface.
Chain oil
Chain oil must demonstrate good adhesion to the chain
and also maintain its flow characteristics regardless of
whether it is warm summer or cold winter weather.
As a chain saw manufacturer we have developed an
optimal chain oil which has a vegetable oil base. We
recommend the use of our own oil for both maximum
chain life and to minimise environmental damage. If our
own chain oil is not available, standard chain oil is
recommended.
Never use waste oil! Using waste oil can be dangerous
to you and damage the machine and environment.
If the chain lubrication is not working:
IMPORTANT! When using vegetable based saw chain
oil, dismantle and clean the groove in the bar and saw
chain before long-term storage.Otherwise there is a risk
of the saw chain oil oxidizing, which will result in the saw
chain becoming stiff and the bar tip sprocket jamming.
•
•
•
Check that the oil channel in the bar is not obstructed.
Clean if necessary.
Filling with chain oil
•
All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also
adjustable.
Check that the groove in the edge of the bar is clean.
Clean if necessary.
•
The saw chain oil tank and the fuel tank are designed
so that the fuel runs out before the saw chain oil.
However, this safety feature requires that you use the
right sort of chain oil (if the oil is too thin it will run out
before the fuel), and that you adjust the carburetor as
recommended (a lean mixture may mean that the fuel
lasts longer than the oil) and that you also use the
recommended cutting equipment (a bar that is too
long will use more chain oil).
Check that the bar tip sprocket turns freely and that
the lubricating hole in the tip sprocket is not blocked.
Clean and lubricate if necessary.
If the chain lubrication system is still not working after
carrying out the above checks and associated measures
you should contact your servicing dealer.
16 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Chain drive sprocket
Bar
Check regularly:
The clutch drum is fitted with one of the following drive
sprockets:
•
Whether there are burrs on the edges of the bar.
Remove these with a file if necessary.
A
Spur sprocket (the chain sprocket is welded on the
drum)
B
Rim sprocket (replaceable)
•
•
Whether the groove in the bar has become badly
worn. Replace the bar if necessary.
Regularly check the degree of wear on the drive sprocket.
Replace if wear is excessive. Replace the drive sprocket
whenever you replace the chain.
Whether the tip of the bar is uneven or badly worn. If
a hollow forms on the underside of the bar tip this is
due to running with a slack chain.
Needle bearing lubrication
Both versions of sprockets have a needle bearing on the
drive shaft, which has to be greased regularly (once a
week).CAUTION! Use only high quality bearing grease or
engine oil.
•
To prolong the life of the bar you should turn it over
regularly.
See instructions under the heading Maintenance, Needle
bearing lubrication.
Checking wear on cutting equipment
WARNING! Most chain saw accidents
happen when the chain touches the
operator.
Check the chain daily for:
!
Wear personal protective equipment. See
instructions under the heading Personal
protective equipment.
Do not tackle any job that you feel you
are not adequately trained for. See
instructions under the headings
Personal protective equipment, How to
avoid kickback, Cutting equipment and
General working instructions.
•
•
•
Visible cracks in rivets and links.
Whether the chain is stiff.
Whether rivets and links are badly worn.
Avoid situations where there is a risk of
kickback. See instructions under the
Replace the saw chain if it exhibits any of the points
above.
′
heading Machine s safety equipment.
We recommend you compare the existing chain with a
new chain to decide how badly the existing chain is worn.
Use the recommended protective
equipment and check its condition. See
instructions under the heading General
working instructions.
When the length of the cutting teeth has worn down to
only 0.16 inch (4 mm) the chain must be replaced.
Check that all the chain saw safety features
are working. See instructions under the
headings General working instructions and
General safety precautions.
115 13 80-96 Rev.3 2008-12-17
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
should be tensioned until it does not sag from the
underside of the bar.
Fitting the bar and chain
WARNING! Always wear gloves, when
working with the chain.
!
The chain is correctly tensioned when there is no slack on
the underside of the bar, and it can still be turned easily
by hand.Tighten the bar nut with the combination spanner
while holding up the tip of the bar.
435
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
Unscrew the bar nut and remove the clutch cover (chain
brake). Take off the transportation ring (A).
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.
Fit the bar over the bar bolt. Place the bar in its rearmost
position.Place the chain over the drive sprocket and in the
groove on the bar. Begin on the top side of the bar.
435e, 440e
Check that the chain brake is in disengaged position by
moving the front hand guard towards the front handle.
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Loosen the chain tensioner wheel and remove the clutch
cover (chain brake). Remove the transport guard. (A)
Mount the clutch cover and remember to fit the chain
adjuster pin in the hole in the bar. Check that the drive
links of the chain fit correctly over the drive sprocket and
that the chain is correctly located in the groove in the bar.
Tighten the bar nut with your fingers.
Tension the chain by turning the chain tensioning screw
clockwise using the combination spanner. The chain
18 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
Fit the bar over the bar bolts. Place the bar in its rearmost
position. Place the chain over the drive sprocket locate it
in the groove on the bar. Begin on the top edge of the bar.
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Mount the clutch cover and remember to fit the chain
adjuster pin in the hole in the bar. Check that the drive
links of the chain fit correctly over the drive sprocket and
that the chain is correctly located in the groove in the bar.
Tension the chain by turning the wheel down (+). The
chain should be tensioned until it does not sag from the
underside of the bar.
The chain is correctly tensioned when it does not sag from
the underside of the bar, but can still be turned easily by
hand. Hold up the bar tip and tighten the bar knob by
turning the knob clockwise.
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.
115 13 80-96 Rev.3 2008-12-17
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
Mixing ratio
Fuel
1:50 (2%) for all engines.
Note! The machine is equipped with a two-stroke engine
and must always be run using a mixture of gasoline and
two-stroke oil. It is important to accurately measure the
amount of oil to be mixed to ensure that the correct
mixture is obtained. When mixing small amounts of fuel,
even small inaccuracies can drastically affect the ratio of
the mixture.
Gasoline, litre
Two-stroke oil, litre
2% (1:50)
0,10
5
10
0,43/0,20
0,30
15
20
0,40
WARNING! Always ensure there is
adequate ventilation when handling fuel.
US gallon
US fl. oz.
2 1/2
!
1
2 1/2
5
6 1/2
Gasoline
12 7/8
Mixing
•
•
Use good quality unleaded gasoline.
CAUTION! Engines equipped with catalytic
converters must be run on unleaded fuel
mixtures. Leaded gasoline will destroy the catalytic
converter and it will no longer serve its purpose. The
green fuel cap on saws fitted with catalytic converters
means that only unleaded gasoline can be used.
•
•
The lowest recommended octane grade is 87
((RON+MON)/2). If you run the engine on a lower
octane grade than 87 so-called knocking can occur.
This gives rise to a high engine temperature and
increased bearing load, which can result in serious
engine damage.
•
•
Always mix the gasoline and oil in a clean container
intended for fuel.
Always start by filling half the amount of the gasoline to
be used.Then add the entire amount of oil. Mix (shake)
the fuel mixture. Add the remaining amount of gasoline.
When working with continuous high revs (e.g.limbing)
a higher octane is recommended.
•
•
•
Mix (shake) the fuel mixture thoroughly before filling
the machine’s fuel tank.
Do not mix more than one month’s supply of fuel at a
time.
Environment fuel
HUSQVARNA recommends the use of alkylate fuel or
environmental fuel for four-stroke engines blended with
two-stroke oil as set out below. Note that carburetor
adjustment may be necessary when changing the type of
fuel (see instructions under the heading Carburetor).
If the machine is not used for some time the fuel tank
should be emptied and cleaned.
Chain oil
•
We recommend the use of special oil (chain oil) with
good adhesion characteristics.
Running-in
Avoid running at a too high speed for extended periods
during the first 10 hours.
Two-stroke oil
•
•
•
For best results and performance use HUSQVARNA
two-stroke engine oil, which is specially formulated for
our air-cooled two stroke-engines.
Never use two-stroke oil intended for water-cooled
engines, sometimes referred to as outboard oil (rated
TCW).
•
•
•
Never use waste oil. This results in damage to the oil
pump, the bar and the chain.
It is important to use oil of the right grade (suitable
viscosity range) to suit the air temperature.
Never use oil intended for four-stroke engines.
In temperatures below 32°F (0°C) some oils become
too viscous.This can overload the oil pump and result
in damage to the oil pump components.
•
Contact your service agent when choosing chain oil.
20 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
FUEL HANDLING
•
Move the machine at least 10 ft (3 m) from the
refuelling point before starting it.
Fueling
WARNING! Taking the following
precautions, will lessen the risk of fire:
!
Do not smoke and do not place any hot
objects in the vicinity of fuel.
Always stop the engine and let it cool for
a few minutes before refuelling.
•
Never start the machine:
1
If you have spilled fuel or chain oil on the machine.
Wipe off the spillage and allow remaining fuel to
evaporate.
When refuelling, open the fuel cap slowly
so that any excess pressure is released
gently.
2
3
If you have spilled fuel on yourself or your clothes,
change your clothes.Wash any part of your body that
has come in contact with fuel. Use soap and water.
Tighten the fuel cap carefully after
refuelling.
If the machine is leaking fuel.Check regularly for leaks
from the fuel cap and fuel lines.
Always move the machine away from the
refuelling area before starting.
WARNING! Never use a machine with
visible damage to the spark plug guard
and ignition cable. A risk of sparking
arises, which can cause a fire.
Clean the area around the fuel cap. Clean the fuel and
chain oil tanks regularly. The fuel filter must be replaced
at least once a year. Contamination in the tanks causes
malfunction. Make sure the fuel is well mixed by shaking
the container before refuelling.The capacities of the chain
oil tank and fuel tank are carefully matched.You should
therefore always fill the chain oil tank and fuel tank at the
same time.
!
Transport and storage
•
Always store the chain saw and fuel so that there is no
risk of leakages or fumes coming into contact with
sparks or naked flames from electrical equipment,
electric motors, relays/switches, boilers and the like.
•
•
Always store fuel in an approved container designed
for that purpose.
For longer periods of storage or for transport of the
chain saw, the fuel and chain oil tanks should be
emptied.Ask where you can dispose of waste fuel and
chain oil at your local gas station.
WARNING! Fuel and fuel vapor are highly
flammable.Take care when handling fuel
and chain oil. Be aware of the risks of
fire, explosion and those associated with
inhalation.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
!
The bar guard must always be fitted to the cutting
attachment when the machine is being transported or
in storage, in order to prevent accident contact with
the sharp chain. Even a non-moving chain can cause
serious cuts to yourself or persons you bump into with
an exposed chain.
Fuel safety
•
Never refuel the machine while the engine is running.
•
Remove the spark plug cap from the spark plug.
Activate the chain brake.
•
Make sure there is plenty of ventilation when refuelling
or mixing fuel (gasoline and 2-stroke oil).
Long-term storage
Empty the fuel/oil tanks in a well ventilated area.Store the
fuel in approved cans in a safe place. Fit the bar guard.
Clean the machine. See instructions under the heading
Maintenance schedule.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 21
STARTING AND STOPPING
Push down the red choke control (4): As soon as the
engine fires which can be heard through a "puff" sound,
push down on the red choke control.
Starting and stopping
WARNING! Note the following before
starting:
Pull the starter handle (5): Keep on pulling the cord
powerfully until the engine starts.
!
The chain brake must be engaged when
the chain saw is started to reduce the
chance of contact with the moving chain
during starting.
Warm engine
Start position (1):The correct choke/start throttle setting
for warm starting is obtained by initially moving the choke
control by pulling the red control outward - upwards.
Never start a chain saw unless the bar,
chain and all covers are fitted correctly.
Otherwise the clutch can come loose and
cause personal injuries.
Air purge (2): Press the air purge diaphragm repeatedly
until fuel fills the diaphragm (at least 6 times). The
diaphragm need not be completely filled.
Push down the red choke control (4): This inactivates
the choke, which is not needed when starting a warm
chain saw.However the movement of the start/stop switch
will have engaged a high idle, making warm starting
easier.
Place the machine on firm ground. Make
sure you have a secure footing and that
the chain cannot touch anything.
Keep people and animals well away from
the working area.
Pull the starter handle (5): Grip the front handle with
your left hand. Hold the chain saw on the ground by
placing your right foot through the rear handle.
Never wrap the starter cord around your
hand.
Starting
The chain brake should be activated when starting the
chain saw. Activate the chain brake by pushing the front
hand guard forwards.
Pull the starter handle with your right hand and pull out the
starter cord slowly until you feel a resistance (as the
starter pawls engage) then pull firmly and rapidly until the
engine fires.
Cold engine
As the chain brake is still engaged the speed of the engine
must be set to idling as soon as possible, this is achieved
by disengaging the throttle lock. Disengagement is done
by gently touching on the throttle trigger. This prevents
unnecessary wear to the clutch, clutch drum and brake
band. Allow the machine to idle a few seconds before
giving full throttle.
Start position (1): Set the start/stop switch in the choke
position by pulling the red control outward - upward.
Air purge (2): Press the air purge diaphragm repeatedly
until fuel fills the diaphragm (at least 6 times). The
diaphragm need not be completely filled.
A
2
1
There is a simplified start reminder with illustrations to
describe each step on the rear edge of the saw (A).
Grip the front handle with your left hand. Hold the chain
saw on the ground by placing your right foot through the
rear handle.
Pull the starter handle (3): Pull the starter handle with
your right hand and pull out the starter cord slowly until
you feel a resistance (as the starter pawls engage) then
pull firmly and rapidly until the engine fires.
22 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
CAUTION! Do not pull the starter cord all the way out and
do not let go of the starter handle when the cord is fully
extended. This can damage the machine.
•
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact with
the cutting equipment.
•
Always hold the saw with both hands. The right hand
should be on the rear handle, and the left hand on the
front handle. All people, whether right or left handed,
should use this grip. Use a firm grip with thumbs and
fingers encircling the chain saw handles.
Note! Pull the front hand guard towards the front
handle.The chain brake is now disengaged.Your saw
is ready for use.
WARNING! Long term inhalation of the
engine’s exhaust fumes, chain oil mist
and dust from sawdust can represent a
health risk.
!
•
Never start a chain saw unless the bar, chain and all
covers are fitted correctly. See instructions under the
heading Assembly. Without a bar and chain attached
to the chain saw the clutch can come loose and cause
serious injury.
•
The chain brake is released by moving the front hand
guard marked ”PULL BACK TO RESET” back,
towards the front handle.
Stopping
•
The chain brake should be activated when starting.Se
instructions under the heading Start and stop. Do not
drop start. This method is very dangerous because
you may lose control of the saw.
Stop the engine by pushing the start/stop switch down.
CAUTION! The start/stop switch automatically returns to
run position. To avoid involuntary start up, the spark plug
cap must always be removed from the spark plug when
the machine is unsupervised.
•
Never start the machine indoors. Exhaust fumes can
be dangerous if inhaled.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 23
WORKING TECHNIQUES
Basic safety rules
Before use:
1
•
Look around you:
To ensure that people, animals or other things cannot
affect your control of the machine.
•
To make sure that none of the above might come
within reach of your saw or be injured by falling trees.
,
1
Check that the chain brake works correctly and is not
damaged.
2
3
Check that the rear right hand guard is not damaged.
Check that the throttle lockout works correctly and is
not damaged.
CAUTION! Follow the instructions above, but do not use a
chain saw in a situation where you cannot call for help in
case of an accident.
4
Check that the stop switch works correctly and is not
damaged.
2
3
4
Do not use the machine in bad weather, such as
dense fog, heavy rain, strong wind, intense cold, etc.
Working in bad weather is tiring and often brings
added risks, such as icy ground, unpredictable felling
direction, etc.
5
6
Check that all handles are free from oil.
Check that the anti vibration system works and is not
damaged.
7
8
9
Check that the muffler is securely attached and not
damaged.
Take great care when removing small branches and
avoid cutting bushes (i.e.cutting many small branches
at the same time). Small branches can be grabbed by
the chain and thrown back at you, causing serious
injury.
Check that all parts of the chain saw are tightened
correctly and that they are not damaged or missing.
Check that the chain catcher is in place and not
damaged.
Make sure you can move and stand safely. Check the
area around you for possible obstacles (roots, rocks,
branches, ditches, etc.) in case you have to move
suddenly. Take great care when working on sloping
ground.
10 Check the chain tension.
General working instructions
IMPORTANT!
This section describes basic safety rules for using a
chain saw. This information is never a substitute for
professional skills and experience. If you get into a
situation where you feel unsafe, stop and seek expert
advice. Contact your chain saw dealer, service agent or
an experienced chain saw user. Do not attempt any task
that you are not sure you can handle!
Before using a chain saw you must understand the
effects of kickback and how to avoid them. See
instructions under the heading How to avoid kickback.
5
Take great care when cutting a tree that is under
tension. A tree that is under tension may spring back
to its normal position before or after being cut. If you
position yourself incorrectly or make the cut in the
wrong place the tree may hit you or the machine and
cause you to lose control. Both situations can cause
serious personal injury.
Before using a chain saw you must understand the
difference between cutting with the top and bottom
edges of the bar. See instructions under the headings
How to avoid kickback and Machine’s safety equipment.
Wear personal protective equipment. See instructions
under the heading Personal protective equipment.
24 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Have control over the workpiece. If the pieces you
intend to cut are small and light, they can jam in the
saw chain and be thrown towards you. Even if this
does not need to be a danger, you may be surprised
and lose control of the saw. Never saw stacked logs or
branches without first separating them. Only saw one
log or one piece at a time. Remove the cut pieces to
keep your working area safe.
6
Before moving your chain saw switch off the engine
and lock the chain using the chain brake. Carry the
chain saw with the bar and chain pointing backwards.
Fit a guard to the bar before transporting the chain
saw or carrying it for any distance.
7
When you put the chain saw on the ground, lock the
saw chain using the chain brake and ensure you have
a constant view of the machine. Switch the engine off
before leaving your chain saw for any length of time.
4
Never use the chain saw above shoulder height
and avoid cutting with the tip of the bar. Never use
the chain saw one-handed!
General rules
1
If you understand what kickback is and how it happens
then you can reduce or eliminate the element of
surprise. By being prepared you reduce the risk.
Kickback is usually quite mild, but it can sometimes be
very sudden and violent.
2
Always hold the chain saw firmly with your right hand
on the rear handle and your left hand on the front
handle. Wrap your fingers and thumbs around the
handles.You should use this grip whether you are
right-handed or left-handed. This grip minimizes the
effect of kickback and lets you keep the chain saw
under control. Do not let go of the handles!
5
In order to keep control of your saw, always maintain
a firm foothold. Never work on a ladder, in a tree or on
any other insecure support.
3
Most kickback accidents happen during limbing. Make
sure you are standing firmly and that there is nothing in
the way that might make you trip or lose your balance.
Lack of concentration can lead to kickback if the
kickback zone of the bar accidentally touches a
branch, nearby tree or some other object.
6
7
Always use a fast cutting speed, i.e. full throttle.
Take great care when you cut with the top edge of the
bar, i.e. when cutting from the underside of the object.
This is known as cutting with a pushing chain. The
chain tries to push the chain saw back towards the
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 25
WORKING TECHNIQUES
user. If the saw chain is jamming, the saw may be
Terms
pushed back at you.
Cutting = General term for cutting through wood.
Limbing = Cutting branches off a felled tree.
Splitting = When the object you are cutting breaks off
before the cut is complete.
There are five important factors you should consider
before making a cut:
1
Make sure the cutting equipment will not jam in the
cut.
8
Unless the user resists this pushing force there is a
risk that the chain saw will move so far backwards that
only the kickback zone of the bar is in contact with the
tree, which can lead to a kickback.
2
3
Make sure the object you are cutting will not split.
Cutting with the bottom edge of the bar, i.e. from the top
of the object downwards, is known as cutting with a
pulling chain. In this case the chain saw pulls itself
towards the tree and the front edge of the chain saw
body rests naturally on the trunk when cutting. Cutting
with a pulling chain gives the operator better control over
the chain saw and the position of the kickback zone.
Make sure the chain will not strike the ground or any
other object during or after cutting.
4
Is there a risk of kickback?
9
Follow the instructions on sharpening and maintaining
your bar and chain. When you replace the bar and
chain use only combinations that are recommended
by us. See instructions under the headings Cutting
equipment and Technical data.
5
Do the conditions and surrounding terrain affect how
safely you can stand and move about?
Two factors decide whether the chain will jam or the object
that you are cutting will split: the first is how the object is
supported before and after cutting, and the second is
whether it is in tension.
Basic cutting technique
WARNING! Never use a chain saw by
holding it with one hand. A chain saw is
not safely controlled with one hand.
Always have a secure, firm grip around
the handles with both hands.
!
In most cases you can avoid these problems by cutting in
two stages; from the top and from the bottom.You need to
support the object so that it will not trap the chain or split
during cutting.
General
•
•
Always use full throttle when cutting!
IMPORTANT! If the chain jams in the cut: stop the
engine! Don’t try to pull the chain saw free. If you do you
may be injured by the chain when the chain saw
suddenly breaks free.Use a lever to open up the cut and
free the chain saw.
Reduce the speed to idle after every cut (running the
engine for too long at full throttle without any load, i.e.
without any resistance from the chain during cutting,
can lead to serious engine damage).
•
•
Cutting from above = Cutting with a pulling chain.
Cutting from below = Cutting with pushing chain.
The following instructions describe how to handle the
common situations you are likely to encounter when using
a chain saw.
Cutting with a pushing chain increases the risk of
kickback. See instructions under the heading How to
avoid kickback.
26 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Limbing
Turn the log and finish the cut from the opposite side.
When limbing thick branches you should use the same
approach as for cutting.
Cut difficult branches piece by piece.
2
1
The log is supported at one end. There is a high risk
that it will split.
3
Start by cutting from below (about 1/3 of the way through).
Finish by cutting from above so that the two cuts meet.
Cutting
WARNING! Never attempt to cut logs
while they are in a pile or when a couple
!
of logs are lying together. Such
procedures drastically increase the risk
of kickback which can result in a serious
or fatal injury.
The log is supported at both ends. There is a high risk
that the chain will jam.
If you have a pile of logs, each log you attempt to cut
should be removed from the pile, placed on a saw horse
or runners and cut individually.
Remove the cut pieces from the cutting area. By leaving
them in the cutting area, you increase the risk for
inadvertently getting a kickback, as well as increasing the
risk of losing your balance while working.
Start by cutting from above (about 1/3 of the way through).
Finish by cutting from below so that the two cuts meet.
The log is lying on the ground. There is little risk of the
chain jamming or the object splitting. However there is a
risk that the chain will touch the ground when you finish
the cut.
Tree felling technique
IMPORTANT! It takes a lot of experience to fell a tree.
Inexperienced users of chain saws should not fell trees.
Do not attempt any task beyond your experience level!
Safe distance
Cut all the way through the log from above. Avoid letting
the chain touch the ground as you finish the cut. Maintain
full throttle but be prepared for what might happen.
The safe distance between a tree that is to be felled and
anyone else working nearby is at least 2 1/2 tree lengths.
Make sure that no-one else is in this ”risk zone” before or
during felling.
If it is possible (can you turn the log?) stop cutting about
2/3 of the way through the log.
115 13 80-96 Rev.3 2008-12-17
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Felling direction
Clearing the trunk and preparing your retreat
The aim is to fell the tree in a position where you can limb
and cross-cut the log as easily as possible.You want it to
fall in a location where you can stand and move about
safely.
Delimb the stem up to shoulder height. It is safer to work
from the top down and to have the tree between you and
the saw.
Once you have decided which way you want the tree to fall
you must judge which way the tree would fall naturally.
Several factors affect this:
•
•
•
•
•
•
Lean of the tree
Bend
Wind direction
Arrangement of branches
Weight of snow
Remove any undergrowth from the base of the tree and
check the area for obstacles (stones, branches, holes,
etc.) so that you have a clear path of retreat when the tree
starts to fall.Your path of retreat should be roughly 135
degrees away from the intended felling direction.
Obstacles within the reach of the tree: for example,
other trees, power lines, roads and buildings.
•
Look for signs of damage and rot in the stem, this
makes it more probably that the tree will break and
start to fall before you expect it to.
D
a
n
g
e
r z
o
n
e
Felling direction
D
Retreat path
Danger zone
a
n
g
e
r z
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to
make it fall in the direction you first intended.
o
n
e
Another very important factor, which does not affect the
felling direction but does affect your safety, is to make sure
the tree has no damaged or dead branches that might
break off and hit you during felling.
Felling
WARNING! Unless you have special
training we advise you not to fell trees
with a diameter larger than the bar length
of your saw!
!
The main point to avoid is letting the tree fall onto another
tree. It is very dangerous to remove a trapped tree and
there is high accident risk. See instructions under the
heading Freeing a tree that has fallen badly.
Felling is done using three cuts. First you make the
directional cuts, which consist of the top cut and the
bottom cut, then you finish with the felling cut. By placing
these cuts correctly you can control the felling direction
very accurately.
Directional cuts
To make the directional cut you begin with the top cut.Aim
using to the saw’s felling direction mark (1) toward a goal
further forward in the terrain, where you would like the tree
to fall (2). Stand on the right-hand side of the tree, behind
the saw, and cut with a pull stroke.
IMPORTANT! During critical felling operations, hearing
protectors should be lifted immediately when sawing is
completed so that sounds and warning signals can be
heard.
28 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Next make the bottom cut so that it finishes exactly at the
end of the top cut.
All control over the felling direction is lost if the felling
hinge is too narrow or non-existent, or if the directional
cuts and felling cut are badly placed.
The directional cuts should run 1/4 of the diameter
through the trunk and the angle between the top cut and
bottom cut should be 45°.
When the felling cut and directional cut are complete the
tree should start to fall by itself or with the aid of a felling
wedge or breaking bar.
The line where the two cuts meet is called the directional
cut line. This line should be perfectly horizontal and at
right angles (90°) to the chosen felling direction.
We recommend that you use a bar that is longer than the
diameter of the tree, so that you can make the felling cut
and directional cuts with single cutting strokes. See
instructions under the heading Technical data section to
find out which lengths of bar are recommended for your
saw.
Felling cut
The felling cut is made from the opposite side of the tree
and it must be perfectly horizontal. Stand on the left side
of the tree and cut on the pull stroke.
Make the felling cut about 1.5-2 inches (3-5 cm) above the
bottom directional cut.
There are methods for felling trees with a diameter larger
than the bar length. However these methods involve a
much greater risk that the kickback zone of the bar will
come into contact with the tree.
Finish the felling cut parallel with the directional cut line so
that the distance between them is at least 1/10 of the
trunk diameter.The uncut section of the trunk is called the
felling hinge.
The felling hinge controls the direction that the tree falls in.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 29
WORKING TECHNIQUES
necessary to reduce the tension and make the tree or
branch break at the point of maximum tension.
Freeing a tree that has fallen badly
Freeing a ”trapped tree”
It is very dangerous to remove a trapped tree and there is
high accident risk.
Never try to fell the tree that is trapped.
Never cut straight through a tree or branch that is in
tension!
Never work in the risk zone of the hanging trapped tree.
If you must cut across tree/limb, make two to three cuts,
one inch apart, one to two inches deep.
Continue to cut deeper until tree/limb bends and tension
is released.
The safest method is to use a winch.
•
Tractor-mounted
Cut tree/limb from outside the bend, after tension has
been released.
•
Portable
How to avoid kickback
WARNING! Kickback can happen very
suddenly and violently; kicking the chain
!
saw, bar and chain back at the user. If
this happens when the chain is moving it
can cause very serious, even fatal
injuries. It is vital you understand what
causes kickback and that you can avoid
it by taking care and using the right
working technique.
Cutting trees and branches that are in tension
Preparations:Work out which side is in tension and where
the point of maximum tension is (i.e. where it would break
if it was bent even more).
What is kickback?
The word kickback is used to describe the sudden
reaction that causes the chain saw and bar to jump off an
object when the upper quadrant of the tip of the bar,
known as the kickback zone, touches an object.
Decide which is the safest way to release the tension and
whether you are able to do it safely. In complicated
situations the only safe method is to put aside your chain
saw and use a winch.
General advice:
Position yourself so that you will be clear of the tree or
branch when the tension is released.
Kickback always occurs in the cutting plane of the bar.
Normally the chain saw and bar are thrown backwards
and upwards towards the user. However, the chain saw
may move in a different direction depending on the way it
Make one or more cuts at or near the point of maximum
tension. Make as many cuts of sufficient depth as
30 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
was being used when the kickback zone of the bar
Cutting the trunk into logs
touched the object.
See instructions under the heading Basic cutting
technique.
Kickback only occurs if the kickback zone of the bar
touches an object.
Limbing
WARNING! A majority of kickback
accidents occur during limbing. Do not
!
use the kickback zone of the guide bar.
Be extremely cautious and avoid
contacting the log, other limbs or objects
with the nose of the guide bar. Be
extremely cautious of limbs under
tension.They can spring back toward
you and cause loss of control resulting
in injury.
Make sure that you can stand and move about safely.
Work on the left side of the trunk. Work as close as
possible to the chain saw for maximum control.If possible,
let the weight of the chain saw rest on the trunk.
Keep the trunk between you and the chain saw as you
move along the trunk.
115 13 80-96 Rev.3 2008-12-17
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
General
Checking, maintaining and
servicing chain saw safety
equipment
The user must only carry out the maintenance and
service work described in this manual. More extensive
work must be carried out by an authorised service
workshop.
Note! All servicing and repair work on the machine
requires special training. This is especially true of the
machine′s safety equipment.If your machine fails any of
the checks described below we recommend you to
contact our servicing dealer.
Carburetor adjustment
Your Husqvarna product has been designed and
manufactured to specifications that reduce harmful
emissions.
Function
Chain brake and front hand guard
•
•
The carburetor governs the engine’s speed via the
throttle control. Air and fuel are mixed in the
carburetor. The air/fuel mixture is adjustable. Correct
adjustment is essential to get the best performance
from the machine.
Checking brake band wear
Brush off any wood dust, resin and dirt from the chain
brake and clutch drum.Dirt and wear can impair operation
of the brake.
The T-screw regulates the throttle setting at idle
speed. If the T-screw is turned clockwise this gives a
higher idle speed; turning it anti-clockwise gives a
lower idle speed.
Basic settings and running in
The basic carburetor settings are adjusted during testing
at the factory. Fine adjustment should be carried out by a
skilled technician.
Rec. idle speed: See the Technical data section.
Fine adjustment of the idling speedT
Adjust the idle speed with the T-screw. If it is necessary to
re-adjust, turn the T-screw clockwise while the engine is
running, until the chain starts to rotate.Then turn counter-
clockwise until the chain stops. A correctly adjusted idle
speed setting occurs when the engine runs smoothly in
every position. It should also be good margin to the rpm
when the chain starts to rotate.
Regularly check that the brake band is at least 0.024 inch
(0.6 mm) thick at its thinnest point.
Checking the front hand guard
WARNING! Contact your servicing
dealer, if the idle speed setting cannot be
adjusted so that the chain stops at idle.
Do not use the chain saw until it has
been properly adjusted or repaired.
Make sure the front hand guard is not damaged and that
there are no visible defects such as cracks.
!
Correctly adjusted carburetor
When the carburetor is correctly adjusted the machine
accelerates without hesitation and the machine 4-cycles a
little at max.speed.It is also important that the chain does
not rotate at idle. If the L-jet is set too lean it may cause
starting difficulties and poor acceleration.If the H-jet is set
too lean the machine will have less power, poor
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to the
clutch cover.
acceleration and could suffer damage to the engine.
32 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Checking the inertia brake release
Apply full throttle and activate the chain brake by tilting
your left wrist forward onto the front hand guard.Do not let
go of the front handle. The chain should stop
immediately.
With the engine turned off, hold the chain saw over a
stump or other firm object. Let go of the front handle so
that the bar drops towards the stump as the chain saw
rotates around the rear handle.
Throttle lockout
•
Make sure the throttle control is locked at the idle
setting when the throttle lockout is released.
When the bar hits the stump the brake should be
applied.
•
Press the throttle lockout and make sure it returns to
its original position when you release it.
Checking the brake trigger
•
•
Check that the throttle control and throttle lockout
move freely and that the return springs work properly.
Place the chain saw on firm ground and start it.Make sure
the chain does not touch the ground or any other object.
See the instructions under the heading Start and stop.
Start the chain saw and apply full throttle. Release the
throttle control and check that the chain stops and
remains stationary. If the chain rotates when the
throttle control is in the idle position you should check
the carburetor idle adjustment.
Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles.
115 13 80-96 Rev.3 2008-12-17
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Chain catcher
Stop switch
Check that the chain catcher is not damaged and is firmly
attached to the body of the chain saw.
Start the engine and make sure the engine stops when
you move the stop switch to the stop setting.
CAUTION! The start/stop switch automatically returns to
run position. In order to prevent unintentional starting, the
spark plug cap must be removed from the spark plug
when assembling, checking and/or performing
maintenance.
Right hand guard
Muffler
Check that the right hand guard is not damaged and that
there are no visible defects, such as cracks.
Never use a machine that has a faulty muffler.
Vibration damping system
Regularly check that the muffler is securely attached to
the machine.
Regularly check the vibration damping units for cracks or
deformation.
Make sure the vibration damping units are securely
attached to the engine unit and handle unit.
Some mufflers are equipped with a special spark arrestor
screen. If your machine has this type of muffler, you
should clean the screen at least once a week.This is best
done with a wire brush. A blocked screen will cause the
engine to overheat and may lead to serious damage.
Note! The screen must be replaced if it is damaged. If the
screen is blocked the machine will overheat and this will
cause damage to the cylinder and piston. Never use a
machine with a muffler that is in poor condition. Never
34 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
use a muffler if the spark arrestor screen is missing
or defective.
•
Undo the bolt in the centre of the pulley and remove
the drive disc (A), drive disc spring (B) and the pulley
(C). Insert and secure a new starter cord in the starter
pulley. Wind approx. 3 turns of the starter cord on the
starter pulley. Fit the starter pulley so that the end of
the recoil spring (D) hooks into the starter pulley. Now
assemble the drive disc spring, drive disc and the bolt
in the centre of the pulley. Carry the starter cord
through the hole in the starter housing and the starter
handle. Tie a good knot on the starter cord.
The muffler is designed to reduce the noise level and to
direct the exhaust gases away from the operator. The
exhaust gases are hot and can contain sparks, which may
cause fire if directed against dry and combustible material.
Starter
WARNING! When the recoil spring is
wound up in the starter housing it is
!
under tension and can, if handled
carelessly, pop out and cause personal
injury.
Care must be exercised when replacing
the return spring or the starter cord.
Wear protective glasses and protective
gloves.
Tensioning the recoil spring
Replacing the starter cord
•
Hook the starter cord in the notch in the pulley and
turn the starter pulley about 2 turns clockwise.
Note! Check that the pulley can be turned an
additional 1/2 turn when the starter cord is pulled all
the way out.
•
Loosen the screws that hold the starter against the
crankcase and remove the starter.
•
Pull out the cord approx. 30 cm (12 inches) and hook
it into the notch in the rim of the pulley. Release the
recoil spring by letting the pulley rotate slowly
backwards.
Stretch the line with the handle. Move your thumb and
release the line. See the figure below.
2
1
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
English – 35
MAINTENANCE
Replacing the return and drive springs
Air filter
Recoil spring (A)
The air filter must be regularly cleaned to remove dust and
dirt in order to avoid:
•
Lift up the starter pulley. See instructions under the
heading Changing a broken or worn starter cord.
Remember that the recoil spring is coiled under
tension in the starter housing.
•
•
•
•
•
•
Carburettor malfunctions
Starting problems
Loss of engine power
•
•
Remove the cassette with the recoil spring from the
starter.
Unnecessary wear to engine parts
Excessive fuel consumption.
Lubricate the recoil spring with light oil. Fit the
cassette with recoil spring in the starter. Fit the starter
pulley and tension the recoil spring.
Remove the air filter after taking off the air filter cover.
When refitting make sure that the air filter seals tightly
against the filter holder. Clean the filter by brushing or
shaking it.
Drive disc spring (B)
•
Undo the bolt in the centre of the pulley and remove
the drive disc and the drive disc spring.
•
Replace the drive disc spring and fit the drive disc
above the spring.
A
B
The filter can be cleaned more thoroughly by washing it in
water and detergent.
An air filter that has been in use for a long time cannot be
cleaned completely. The filter must therefore be replaced
with a new one at regular intervals. A damaged air filter
must always be replaced.
Fitting the starter
A HUSQVARNA chain saw can be equipped with different
types of air filters according to working conditions,
weather, season, etc. Contact your dealer for advice.
•
To fit the starter, first pull out the starter cord and place
the starter in position against the crankcase. Then
slowly release the starter cord so that the pulley
engages with the pawls.
•
Fit and tighten the screws that hold the starter.
36 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Spark plug
Needle bearing lubrication
The clutch drum has a needle bearing on the output shaft.
This needle bearing must be lubricated regularly.
The spark plug condition is influenced by:
•
•
Incorrect carburetor adjustment.
When lubricating, remove the clutch cover by loosening
the two bar nuts. Lay the saw on its side with the clutch
drum upwards.
An incorrect fuel mixture (too much or incorrect type of
oil).
•
A dirty air filter.
Lubrication involves engine oil dripping into the centre of
the clutch drum as it rotates.
These factors cause deposits on the spark plug
electrodes, which may result in operating problems and
starting difficulties.
If the machine is low on power, difficult to start or runs
poorly at idle speed: always check the spark plug first
before taking any further action. If the spark plug is dirty,
clean it and check that the electrode gap is 0.020 inch (0.5
mm). The spark plug should be replaced after about a
month in operation or earlier if necessary.
Cooling system
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The cooling system consists of:
Note! Always use the recommended spark plug type! Use
of the wrong spark plug can damage the piston/cylinder.
Check that the spark plug is fitted with a suppressor.
1
2
3
4
5
Air intake on the starter.
Air guide plate.
Lubricating the bar tip sprocket
Fins on the flywheel.
Cooling fins on the cylinder.
Cylinder cover (directs cold air over the cylinder).
Lubricate the bar tip sprocket each time you refuel. Use
the special grease gun and a good quality bearing grease.
Clean the cooling system with a brush once a week, more
often in demanding conditions. A dirty or blocked cooling
system results in the machine overheating which causes
damage to the piston and cylinder.
115 13 80-96 Rev.3 2008-12-17
English – 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
°
°
Temperature -5 C (23 F) or colder:
”Air Injection” centrifugal
cleaning
Centrifugal cleaning means the following: All air to the
carburetor passes through the starter. Dirt and dust is
pushed out by the cooling fan.
For running the machine in cold weather or powder snow,
a special cover is available, which is mounted on the
starter housing. This reduces the intake of cold air and
prevents large amounts of snow from being sucked in.
IMPORTANT! In order to maintain operation of the
centrifugal cleaning system it must be regularly
maintained. Clean the air intake to the starter, the fins on
the flywheel, the space around the flywheel, inlet pipe and
carburetor compartment.
CAUTION! If the special winterising kit has been fitted or
any measures have been taken to increase the
temperature these changes must be reversed before the
machine is used in normal temperature conditions.
Otherwise there is a risk of overheating, resulting in
severe damage to the engine.
Winter use
Running problems can occur when using the machine in
the cold and snowy conditions caused by:
•
•
Too low engine temperature.
Icing of the air filter and carburetor.
IMPORTANT! Any maintenance other than that described
in this manual must be carried out by your servicing dealer
(retailer).
Special measures are therefore often required:
•
Partly mask the air inlet on the starter to increase the
working temperature of the engine.
38 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance that must be performed on the machine. Most of the items are described in the
Maintenance section.
Daily maintenance
Weekly maintenance
Monthly maintenance
Check the brake band on the chain
brake for wear. Replace when less
than 0.024 inch (0.6 mm) remains at
the most worn point.
On chain saws without a catalytic
converter, check the cooling system
weekly.
Clean the outside of the machine.
Check that the components of the
throttle control work safely. (Throttle
lockout and throttle control.)
Check the starter, starter cord and
return spring.
Check the clutch centre, clutch drum
and clutch spring for wear.
Clean the chain brake and check that
it operates safely. Make sure that the Check that the vibration damping
Clean the spark plug. Check that the
electrode gap is 0.020 inch (0.5 mm).
chain catcher is undamaged, and
replace it if necessary.
elements are not damaged.
The bar should be turned regularly for
more even wear. Check the
lubrication hole in the bar, to be sure it
is not clogged. Clean the bar groove.
If the bar has a sprocket tip, this
should be lubricated.
Lubricate the clutch drum bearing.
Clean the outside of the carburetor.
Check that the bar and chain are
getting sufficient oil.
File off any burrs from the edges of
the bar.
Check fuel hose for cracks or other
damage. Change if necessary.
Check the saw chain with regard to
visible cracks in the rivets and links,
whether the saw chain is stiff or
whether the rivets and links are
abnormally worn. Replace if
necessary.
Clean or replace the spark arrestor
screen on the muffler.
Empty the fuel tank and clean the
inside.
Sharpen the chain and check its
tension and condition.Check the drive
sprocket for excessive wear and
replace if necessary.
Empty the oil tank and clean the
inside.
Clean the carburetor compartment.
Clean the air filter. Replace if
necessary.
Clean the starter units air intake.
Check all cables and connections.
Check that nuts and screws are tight.
Check that the stop switch works
correctly.
Check that there are no fuel leaks
from the engine, tank or fuel lines.
On chain saws with a catalytic
converter, check the cooling system
daily.
English – 39
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
435
435e
440e
Engine
Cylinder displacement, cu.in/cm3
Cylinder bore, inch/mm
Stroke, inch/mm
2,49/40,9
1,61/41
2,49/40,9
1,61/41
2,49/40,9
1,61/41
1,22/31
1,22/31
1,22/31
Idle speed, rpm
2900
2900
2900
Power, kW/hp @ rpm
Ignition system
1,6/2,2 @ 9000
1,6/2,2 @ 9000
1,8/2,4 @ 9000
Manufacturer of ignition system
Type of ignition system
Spark plug
Walbro
Walbro
Walbro
MBU-33
MBU-33
MBU-33
NGK BPMR 7A/
NGK BPMR 7A/
NGK BPMR 7A/
Champion RCJ 7Y/ Champion RCJ 7Y/ Champion RCJ 7Y/
Husqvarna PR 17Y Husqvarna PR 17Y Husqvarna PR 17Y
Electrode gap, inch/mm
Fuel and lubrication system
Manufacturer of carburetor
Carburetor type
0,02/0,5
0,02/0,5
0,02/0,5
Zama
Zama
Zama
EL 41
EL 41
EL 41
Fuel tank capacity, US pint/litre
Oil pump capacity at 9,000 rpm, ml/min
Oil tank capacity, US pint/litre
Type of oil pump
0,78/0,37
13
0,78/0,37
13
0,78/0,37
13
0,53/0,25
Not adjustable
0,53/0,25
Not adjustable
0,53/0,25
Not adjustable
Weight
Chain saw without bar or chain, empty tanks, lb/kg 9,3/4,2
9,7/4,4
9,7/4,4
Chain/bar
Standard bar length, inch/cm
Recommended bar lengths, inch/cm
Usable cutting length, inches/cm
Pitch, inch/mm
13"/33
13"/33
13"/33
13-18"/33-46
12-17"/31-43
0,325/8,25
0,050/1,3
Spur/7
13-18"/33-46
12-17"/31-43
0,325/8,25
0,050/1,3
Spur/7
13-18"/33-46
12-17"/31-43
0,325/8,25
0,050/1,3
Spur/7
Thickness of drive links, inch/mm
Drive sprocket type/teeth
Chain speed at max. power, m/sec
17,3
17,3
17,3
40 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Recommended original and replacement bar and chain combinations
Following is a list of recommended cutting equipment for the Husqvarna chain saw models 435, 435e and 440e. The
combinations of power head, bar and chain have been tested and found to be in accordance with the kickback and
vibration requirements of ANSI B175.1–2000.
The guide bar nose radius is determined by either the maximum number of teeth in the nose sprocket or the
corresponding maximum nose radius of a solid bar.
The following list is the chain saw manufacturers recommendations. There may be other combinations available, which
will also achieve kickback reduction.
As we are listing the maximum guide bar nose radius, you may use a guide bar with smaller nose radius than in our list.
For guide bars of the same length, all sprocket-nose guide bars of the same pitch and having the same number of
sprocket teeth may be considered to have equivalent kickback energy. A hard nose bar having the same length and nose
radius as a sprocket-nose bar may be considered to have equivalent or less kickback energy than the sprocket-nose bar.
Bar and chain combinations
Chain saw models Husqvarna 435, 435e and 440e met the kickback performance requirements of ANSI B 175.1-2000
when tested with the combinations of bars and saw chains listed below.The saw chain Husqvarna H30 is also classified
as a low kickback saw chain since it met the requirements for low kickback saw chain outlined in ANSI B 175.1-2000.
We recommend to use only the listed combinations of bars and chains for chain saw models Husqvarna 435, 435e and
440e. Other chain saw models may not meet the kickback requirements when equipped with the listed bar and chain
combinations.
Bar
Chain
Drive link count
Thickness of drive
links, inch/mm
Length, inch
Pitch, inch
Max. nose radius
Type
13
15
16
18
0,325
0,325
0,325
0,325
10T
10T
10T
10T
56
64
66
72
1,3
Husqvarna H30
Saw chain filing and file gauges
English – 41
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL AND CALIFORNIA EMISSIONS CONTROLWARRANTY STATEMENT
WARRANTY COMMENCEMENT DATE
YOUR WARRANTY RIGHTS AND
OBLIGATIONS
The warranty period begins on the date the engine or
equipment is delivered to an ultimate purchaser.
The EPA (U.S. Environmental Protection Agency), CARB
LENGTH OF COVERAGE
(California Air Resources Board), Environment Canada
and Husqvarna Forest & Garden are pleased to explain
the emissions control system’s warranty on your 2009 and
later small off-road engine. In U.S. and Canada, new
equipment that use small off-road engines must be
designed, built, and equipped to meet the applicable
Federal or Californian stringent anti-smog standards.
Husqvarna Forest & Garden must warrant the emissions
control system on your small off-road engine for the
period listed below provided there has been no abuse,
neglect or improper maintenance of your equipment.Your
emissions control system may include parts such as the
carburetor, ignition system, catalytic converter, fuel tank,
filters and other associated components. Also, included
may be hoses, belts, connectors, sensors, and other
emission-related assemblies. Where a warrantable
condition exists, Husqvarna Forest & Garden will repair
your small off-road engine at no cost to you including
diagnosis, parts and labor.
Husqvarna Forest & Garden warrants to the ultimate
purchaser and each subsequent owner that the engine or
equipment is designed, built, and equipped so as to
conform with all applicable regulations adopted by EPA
and CARB, and is free from defects in materials and
workmanship that causes the failure of a warranted part
for a period of two years.
WHAT IS COVERED
REPAIR OR REPLACEMENT OF PARTS Repair or
replacement of any warranted part under the warranty
must be performed at no charge to the owner at a
warranty station. Warranty services or repairs will be
provided at all Husqvarna Forest & Garden distribution
centers that are franchised to service the subject engines.
Throughout the emissions warranty period of two years,
Husqvarna Forest & Garden must maintain a supply of
warranted parts sufficient to meet the expected demand
for such parts.
′
MANUFACTURER S WARRANTY
COVERAGE
WARRANTY PERIOD Any warranted part that is
scheduled for replacement as required in the
The emissions control system is warranted for two years.
If any emissions-related part on your equipment is
defective, the part will be repaired or replaced by
Husqvarna Forest & Garden.
maintenance schedule, is warranted for the period of time
prior to the first scheduled replacement point for that part.
If the part fails prior to the first scheduled replacement, the
part will be repaired or replaced by Husqvarna Forest &
Garden at no cost. Any such part repaired or replaced
under warranty is warranted for the remainder of the
period prior to the first scheduled replacement point for
the part. Any warranted part that is not scheduled for
replacement as required in the maintenance schedule, is
warranted for two years. If any such part fails during the
period of warranty coverage, it will be repaired and
replaced by Husqvarna Forest & Garden at no cost. Any
such part repaired or replaced under the warranty is
warranted for the remaining warranty period. Any
warranted part that is scheduled only for regular
inspection in the maintenance schedule will be warranted
for a period of two years. A statement in such written
instructions to the effect of ”repair or replace as
necessary” will not reduce the period of warranty
coverage. Any such part repaired or replaced under
warranty will be warranted for the remaining warranty
period.
′
OWNER S WARRANTY
RESPONSIBILITIES
•
As the small off-road engine owner, you are
responsible for performance of the required
maintenance listed in your operator’s manual.
Husqvarna Forest & Garden recommends that you
retain all receipts covering maintenance on your small
off-road engine, but Husqvarna Forest & Garden
cannot deny warranty solely for the lack of receipts or
your failure to ensure the performance of all
scheduled maintenance.
•
•
As the small off-road engine owner, you should
however be aware that Husqvarna Forest & Garden
may deny you warranty coverage if your small off-road
engine or a part has failed due to abuse, neglect, or
improper maintenance or unapproved modifications.
You are responsible for presenting your small off-road
engine to a Husqvarna Forest & Garden distribution
center or service center as soon as the problem
exists.The warranty repairs should be completed in a
reasonable amount of time, not to exceed 30 days. If
you have any questions regarding your warranty
coverage, you should contact Husqvarna Forest &
Garden at 1-800-487-5951 or visit
DIAGNOSIS The owner must not be charged for
diagnostic labor that leads to the determination that a
warranted part is in fact defective, provided that such
diagnostic work is performed at a warranty station.
CONSEQUENTIAL DAMAGES Husqvarna Forest &
Garden is liable for damages to other engine components
proximately caused by a failure under warranty of any
warranted part.
42 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
FEDERAL AND CALIFORNIA EMISSIONS CONTROLWARRANTY STATEMENT
EMISSION WARRANTY PARTS LIST
1
2
3
Carburetor and internal parts
Intake pipe, airfilter holder and carburetor bolts.
Airfilter and fuelfilter covered up to maintenance
schedule.
4
5
6
7
Spark Plug, covered up to maintenance schedule
Ignition Module
Muffler with catalytic converter
Fuel tank
WHAT IS NOT COVERED
All failures caused by abuse, neglect or improper
maintenance are not covered.
ADD -ON OR MODIFIED PARTS
Add-on or modified parts that are not exempted by CARB
or EPA may not be used. The use of any non-exempted
add-on or modified parts will be grounds for disallowing a
warranty claim. Husqvarna Forest & Garden will not be
liable to warrant failures of warranted parts caused by the
use of a non-exempted add-on or modified part.
HOW TO FILE A CLAIM
If you have any questions regarding your warranty rights
and responsibilities, you should contact your nearest
authorized servicing dealer or call Husqvarna Forest &
Garden at 1-800-487-5951 or visit
WHERE TO GET WARRANTY SERVICE
Warranty services or repairs are provided through all
Husqvarna Forest & Garden authorized servicing dealers.
MAINTENANCE, REPLACEMENT AND
REPAIR OF EMISSION-RELATED PARTS
Any replacement part may be used in the performance of
any warranty maintenance or repairs and must be
provided without charge to the owner. Such use will not
reduce the warranty obligations of the manufacturer.
MAINTENANCE STATEMENT
The owner is responsible for the performance of all
required maintenance, as defined in the operator’s
manual.
English – 43
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
AMERICAN STANDARD SAFETY PRECAUTIONS
Other safety precautions
Safety precautions for chain saw
users
(ANSI B175.1-2000 Annex C)
WARNING! Do not operate a chain saw
with one hand! Serious injury to the
operator, helpers, bystanders or any
combination of these persons may result
from one-handed operation. A chain saw
is intended for two-handed use.
!
Kickback safety precautions
WARNING! Kickback may occur when the
nose or tip of the guide bar touches an
object, or when the wood closes in and
pinches the saw chain in the cut.
!
Do not operate a chain saw when you are fatigued.
Use safety footwear; snug-fitting clothing, protective
gloves, and eye, hearing and head protection devices.
Tip contact in some cases may cause a
lightning fast reverse reaction, kicking
the guide bar up and back towards the
operator.
Use caution when handling fuel. Move the chain saw at
least 10 feet (3 m) from the fueling point before starting
the engine.
Do not allow other persons to be near the chain saw when
starting or cutting with the chain saw. Keep bystanders
and animals out of the work area.
Pinching the saw chain along the top of
the guide bar may push the guide bar
rapidly back towards the operator.
Do not start cutting until you have a clear work area,
secure footing and a planned retreat path from the falling
tree.
Either of these reactions may cause you
to lose control of the saw which could
result in serious personal injury.
Keep all parts of your body away from the saw chain when
the engine is running.
Do not rely exclusively upon the safety
devices built into your saw. As a chain
saw user, you should take several steps
to keep your cutting jobs free from
accident or injury.
Before you start the engine, make sure that the saw chain
is not contacting anything.
Carry the chain saw with the engine stopped, the guide
bar and saw chain to the rear, and the muffler away from
your body.
Do not operate a chain saw that is damaged, improperly
adjusted, or not completely and securely assembled. Be
sure that the saw chain stops moving when the throttle
control trigger is released.
With a basic understanding of kickback, you can reduce
or eliminate the element of surprise. Sudden surprise
contributes to accidents.
Keep a good firm grip on the saw with both hands, the
right hand on the rear handle, and the left hand on the
front handle, when the engine is running. Use a firm grip
with thumbs and fingers encircling the chain saw handles.
A firm grip will help you reduce kickback and maintain
control of the saw. Don’t let go.
Shut off the engine before setting the chain saw down.
Use extreme caution when cutting small size brush and
saplings because slender material may catch the saw
chain and be whipped toward you or pull you off balance.
When cutting a limb that is under tension be alert for
springback so that you will not be struck when the tension
in the wood fibers is released.
Make sure that the area in which you are cutting is free
from obstacles. Do not let the nose of the guide bar
contact a log, branch, or any other obstacle which could
be hit while you are operating the saw.
Keep handles dry, clean and free of oil or fuel mixture.
Operate the chain saw only in well-ventilated areas.
Do not operate a chain saw in a tree unless you have
been specifically trained to do so.
Cut at high engine speeds.
Do not overreach or cut above shoulder height.
Do not operate a chain saw above shoulder height.
Follow manufacturer’s sharpening and maintenance
instructions for the saw chain.
All chain saw service, other than the items listed in the
operator’s/owner’s safety and maintenance instructions,
should be performed by competent chain saw service
personnel. (For example, if improper tools are used to
remove the flywheel or if an improper tool is used to hold
the flywheel in order to remove the clutch, structural
damage to the flywheel could occur and subsequently
cause the flywheel to burst.)
Only use replacement bars and chains specified by the
manufacturer or the equivalent.
When transporting your chain saw, use the appropriate
guide bar guard.
Note:This Annex is intended primarily for the consumer or
occasional user.
44 – English
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
ACLARACION DE LOS SIMBOLOS
Símbolos en la máquina:
Símbolos en el manual de
instrucciones:
Los trabajos de control y/o
mantenimiento deben efectuarse
con el motor desconectado.
¡NOTA! El contacto de arranque/
parada retorna automáticamente
a la posición de marcha. Por
consiguiente, para evitar el arranque involuntario hay que
quitar siempre el capuchón de encendido de la bujía
antes de realizar trabajos de montaje, control y/o
mantenimiento.
¡ATENCION! ¡Las motosierras pueden
ser peligrosas! Su uso descuidado o
erróneo puede provocar heridas graves o
mortales al operador o terceros.
Lea detenidamente el manual de
instrucciones y asegúrese de entender
su contenido antes de utilizar la
máquina.
Utilice siempre:
•
•
Casco protector homologado
Protectores auriculares
homologados
•
Gafas protectoras o visor
Utilice siempre guantes protectores
homologados.
El operador debe manejar la motosierra
con ambas manos.
La máquina debe limpiarse
regularmente.
No manejar nunca una motosierra
sujetándola sólo con una mano.
Control visual.
Debe evitarse que la punta de la espada
entre en contacto con ningún objeto.
El contacto con la puntera podría
provocar un movimiento repentino hacia
arriba y hacia abajo de la espada guía
(llamado «reculada»), lo que podría
causar graves lesiones.
Debe utilizarse gafas protectoras o
visor.
Los demás símbolos/etiquetas que aparecen en la
máquina corresponden a requisitos de
homologación específicos en determinados
mercados.
Carga de combustible.
Carga de aceite y regulación del
caudal de aceite.
El freno de cadena debe estar
activado al poner en marcha la
motosierra.
¡ATENCION! Si la punta de la espada
toca en un objeto se puede producir
reculada que lanza la espada hacia
arriba y atrás contra el usuario. Ello
puede causar daños personales graves.
115 13 80-96 Rev.3 2008-12-17
Spanish – 45
Download from Www.Somanuals.com. All Manuals Search And Download.
ACLARACION DE LOS SIMBOLOS
Etiquetas que se encuentran en la motosierra:
EPA III
El período de cumplimiento de emisiones mencionado en
la etiqueta de cumplimiento de emisiones indica el
número de horas de funcionamiento en el que el motor ha
demostrado cumplir con los requisitos federales en
materia de emisiones.
El mantenimiento, sustitución o reparación de aparatos y
sistemas de control de las emisiones puede efectuarlos
cualquier establecimiento o individuo dedicado a la
reperación de motores no de carretera.
46 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INDICE
Índice
DECLARACIÓN DE GARANTÍA DE CONTROL
DE EMISIONES FEDERALY CALIFORNIANA
ACLARACION DE LOS SIMBOLOS
INDICE
SUS DERECHOS Y OBLIGACIONES DE
PRECAUCIONES DE SEGURIDAD DE LA
NORMA AMERICANA
INTRODUCCION
Precauciones de seguridad para usuarios de
¿QUE ES QUE?
¿Qué es qué en la motosierra? ............................ 49
INSTRUCCIONES GENERALES DE
SEGURIDAD
Medidas a tomar antes de utilizar una motosierra
MONTAJE
MANIPULACION DEL COMBUSTIBLE
ARRANQUEY PARADA
TECNICA DE TRABAJO
MANTENIMIENTO
Control, mantenimiento y servicio del equipo de
DATOS TECNICOS
115 13 80-96 Rev.3 2008-12-17
Spanish – 47
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCCION
Apreciado cliente:
¡Felicidades por haber adquirido un producto Husqvarna! La historia de Husqvarna data del año 1689, cuando el Rey
Karl XI encargó la construcción de una fábrica en la ribera del río Huskvarna para la fabricación de mosquetes. La
ubicación junto al río Huskvarna era lógica, dado que el río se utilizaba para generar energía hidráulica. Durante los más
de 300 años de existencia de la fábrica Husqvarna, se han fabricado productos innumerables; desde estufas de leña
hasta modernas máquinas de cocina, máquinas de coser, bicicletas, motocicletas, etc. En 1956 se introdujo el primer
cortacésped motorizado, seguido de la motosierra en 1959; y es en este segmento en el que actualmente trabaja
Husqvarna.
Husqvarna es hoy uno de los principales fabricantes del mundo de productos de bosque y jardín, con la calidad y las
prestaciones como principal prioridad.La idea de negocio es desarrollar, fabricar y comercializar productos motorizados
para silvicultura y jardinería, así como para las industrias de construcción y obras públicas. Husqvarna tiene como
objetivo estar en la vanguardia en lo que respecta a ergonomía, facilidad de empleo, seguridad y consideración
ambiental; motivo por el cual ha desarrollado una serie de detalles para mejorar los productos en estas áreas.
Estamos convencidos de que usted apreciará con satisfacción la calidad y prestaciones de nuestro producto por mucho
tiempo en adelante. Con la adquisición de alguno de nuestros productos, usted dispone de asistencia profesional con
reparaciones y servicio en caso de ocurrir algo. Si ha adquirido el producto en un punto de compra que no es uno de
nuestros concesionarios autorizados, pregúnteles por el taller de servicio más cercano.
Esperamos que su máquina le proporcione plena satisfacción y le sirva de ayuda por mucho tiempo en adelante.Tenga
en cuenta que este manual de instrucciones es un documento de valor. Siguiendo sus instrucciones (de uso, servicio,
mantenimiento, etcétera) puede alargar considerablemente la vida útil de la máquina e incrementar su valor de reventa.
Si vende su máquina, entregue el manual de instrucciones al nuevo propietario.
¡Gracias por utilizar un producto Husqvarna!
Husqvarna AB trabaja constantemente para perfeccionar sus productos y se reserva, por lo tanto, el derecho a introducir
modificaciones en la construcción y el diseño sin previo aviso.
48 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
¿QUE ES QUE?
¿Qué es qué en la motosierra?
1
2
3
4
5
6
7
8
9
Cubierta del cilindro
16 Silenciador
17 Cadena
Bomba de combustible
Recordatorio de arranque
18 Cabezal de rueda
Contacto de arranque y parada combinado
Mango trasero
19 Espada
20 Apoyo de corteza
21 Captor de cadena
22 Rueda de tensor de cadena
23 Cubierta del embrague
24 Protección de la mano derecha
25 Acelerador
Etiqueta adhesiva de información y advertencia
Depósito de combustible
Tornillos de reglaje del carburador
Empuñadura de arranque
10 Mecanismo de arranque
11 Depósito de aceite de cadena
12 Placa de identificatión
26 Fiador del acelerador
27 Perilla
13 Marca de orientación de tala
14 Mango delantero
28 Manual de instrucciones (EPA)
29 Protección de la espada
30 Llave combinada
15 Protección contra reculadas
Spanish – 49
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
Medidas a tomar antes de utilizar
una motosierra nueva
¡ATENCION! No permita nunca que los
niños utilicen la máquina ni permanezcan
cerca de ella. Dado que la máquina tiene
un contacto de parada con retorno por
muelle, se puede arrancar con poca
velocidad y fuerza en la empuñadura de
arranque, incluso niños pequeños pueden,
en determinadas circunstancias, lograr la
fuerza necesaria para arrancar la máquina.
Ello puede comportar riesgo de daños
personales graves. Por consiguiente,
saque el capuchón de encendido cuando
vaya a dejar la máquina sin vigilar.
!
•
Lea detenidamente el manual de instrucciones.
•
Compruebe el montaje y ajuste del equipo de corte.
Vea las instrucciones bajo el título Montaje.
•
•
•
Ponga combustible y arranque la motosierra. Vea las
instrucciones en los capítulos Manipulación del
combustible y Arranque y parada.
No utilice la motosierra hasta que haya llegado
suficiente aceite lubricante a la cadena. Vea las
instrucciones bajo el título Equipo de corte.
La exposición prolongada al ruido puede causar
daños crónicos en el oído, Por consiguiente, use
siempre protectores auriculares homologados.
Importante
¡IMPORTANTE!
La máquina sólo está diseñada para aserrar madera.
¡ATENCION! Bajo ninguna circunstancia
Utilice solamente las combinaciones de espada/cadena
de sierra recomendadas en el capítulo Datos técnicos.
debe modificarse la configuración
!
original de la máquina sin autorización
del fabricante. Utilizar siempre recambios
originales. Las modificaciones y/o la
utilización de accesorios no autorizadas
pueden ocasionar accidentes graves o
incluso la muerte del operador o de
terceros. Su garantía podría no abarcar
daños o responsabilidades causados por
el uso de accesorios o piezas de
Nunca utilice la máquina si está cansado, si ha ingerido
alcohol o si toma medicamentos que puedan afectarle
la vista, su capacidad de discernimiento o el control del
cuerpo.
Utilice el equipo de protección personal. Vea las
instrucciones bajo el título Equipo de protección personal.
No modifique nunca esta máquina de forma que se
desvíe de la versión original, y no la utilice si parece
haber sido modificada por otras personas.
repuesto no autorizados.
No utilice nunca una máquina defectuosa. Siga las
instrucciones de mantenimiento, control y servicio de
este manual. Algunas medidas de mantenimiento y
servicio deben ser efectuadas por especialistas
formados y cualificados. Vea las instrucciones bajo el
título Mantenimiento.
¡ATENCION! La utilización errónea o
descuidada de una motosierra puede
convertirla en una herramienta peligrosa
que puede causar accidentes graves e
incluso mortales. Es muy importante que
lea y comprenda el contenido de este
manual de instrucciones.
!
Nunca utilice otros accesorios que los recomendados
en este manual. Vea las instrucciones bajo los títulos
Equipo de corte y Datos técnicos.
¡ATENCION! En el interior del
¡NOTA! Utilice siempre gafas protectoras o visera para
reducir el riesgo de daños causados por objetos
lanzados. Una motosierra puede lanzar con gran fuerza
objetos como virutas, trozos de madera pequeños, etc.
Ello comporta riesgo de daños personales graves,
especialmente en los ojos.
silenciador hay sustancias químicas que
!
pueden ser cancerígenas. Evitar el
contacto con estas sustancias si se daña
el silenciador.
¡ATENCION! La inhalación prolongada
de los gases de escape del motor, la
neblina de aceite de cadena y el polvo de
serrín puede poner en riesgo la salud.
!
¡ATENCION! Si se hace funcionar el
motor en un local cerrado o mal
ventilado, se corre riesgo de muerte por
asfixia o intoxicación con monóxido de
carbono.
!
¡ATENCION! El sistema de encendido de
esta máquina genera un campo
electromagnético durante el
!
¡ATENCION! Un equipo de corte
defectuoso o una combinación errónea
funcionamiento. Este campo magnético
puede, en determinadas circunstancias,
interferir con marcapasos. Para reducir
el riesgo de lesiones graves o letales, las
personas que utilizan marcapasos deben
consultar con su médico y con el
fabricante del marcapasos antes de
emplear esta máquina.
!
de espada/cadena de sierre aumentan el
riesgo de reculadas. Utilice solamente
las combinaciones de espada/cadena de
sierra recomendadas y siga las
instrucciones.Vea las instrucciones bajo
el titular Datos técnicos
50 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
•
Botas con protección anticorte, puntera de acero y
suela antideslizante
Emplee siempre el sentido común
Es imposible abarcar todas las situaciones imaginables
que se pueden producir al utilizar una motosierra.
Proceda con cuidado y emplee el sentido común. Evite
todo uso para el cual no se sienta suficientemente
calificado. Si después de leer estas instrucciones todavía
se siente inseguro en cuanto al procedimiento de uso,
consulte con un experto antes de proseguir. No dude en
ponerse en contacto con el distribuidor o con nosotros si
tiene alguna duda en cuanto al empleo de la motosierra.
Estamos a su disposición para darle consejos que le
ayuden a emplear su motosierra de forma mejor y más
segura. Le recomendamos hacer un cursillo sobre
empleo de motosierras. El distribuidor local, una escuela
de silvicultura o una biblioteca pueden informarle acerca
del material de formación y los cursos disponibles.
•
•
Tenga siempre a mano el equipo de primeros auxilios.
Extintor de incendios y pala
Utilice prendas ajustadas que no limiten su movilidad.
¡IMPORTANTE! Pueden producirse chispas en el
silenciador, la espada y la cadena o en otra fuente.
Tenga siempre a mano herramientas para extinguir
incendios, por si fueran necesarias. Así ayudará a
prevenir incendios forestales.
Equipo de seguridad de la
máquina
En este capítulo se explican los componentes de
seguridad de la máquina y sus funciones. Para el control
y mantenimiento, vea las instrucciones del capítulo
Control, mantenimiento y servicio del equipo de
seguridad de la motosierra.Vea el capítulo Componentes
de la máquina para ver dónde están situados estos
componentes en su máquina.
La vida útil de la máquina puede acortarse y el riesgo de
accidentes puede aumentar si el mantenimiento de la
máquina no se hace de forma adecuada y si los trabajos
de servicio y/o reparación no se efectúan de forma
profesional. Para más información, consulte con el taller
de servicio oficial más cercano.
¡ATENCION! No emplee nunca una
máquina con equipo de seguridad
Se realiza un trabajo constante de mejoras del diseño y la
técnica, que aumentan su seguridad y eficacia. Visite al
distribuidor local regularmente para averiguar qué provecho
pueden proporcionarle las novedades que se introducen.
!
defectuoso. El equipo de seguridad se
debe controlar y mantener. Vea las
instrucciones del capítulo Control,
mantenimiento y servicio del equipo de
seguridad de la motosierra. Si el control
de su máquina no da resultado
Equipo de protección personal
¡ATENCION! La mayoría de los
satisfactorio, hay que acudir a un taller
de servicio para la reparación.
accidentes con la motosierra se
!
producen cuando la cadena toca al
usuario. Para trabajar con la máquina
debe utilizarse un equipo de protección
personal homologado. El equipo de
protección personal no elimina el riesgo
de lesiones, pero reduce su efecto en
caso de accidente. Pida a su distribuidor
que le asesore en la elección del equipo.
Freno de cadena con protección contra
reculadas
Su motosierra está equipada con un freno de cadena
diseñado para detener la cadena de sierra en caso de
reculada. Un freno de cadena reduce el riesgo de
accidentes, pero sólo es usted, el usuario, quien puede
impedirlos.
Proceda con cuidado en la utilización de la sierra,
procurando que el sector de riesgo de reculada de la
espada nunca toque ningún objeto.
•
•
•
•
•
Casco protector homologado
Protectores auriculares
Gafas protectoras o visor
Guantes con protección anticorte
Pantalones con protección contra sierra
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 51
INSTRUCCIONES GENERALES DE SEGURIDAD
•
•
El freno de cadena (A) se activa bien manualmente
(con la mano izquierda) o por efecto de la inercia.
•
Para liberar el freno de cadena, mueva hacia atrás
(en dirección a la empuñadura del mango) la
protección contra reculadas con la inscripción
«TIRAR HACIA ATRÁS PARA REINICIAR».
La activación se produce al empujar hacia delante la
protección contra reculadas (B).
•
El movimiento activa un mecanismo de muelle que tensa
la cinta del freno (C) alrededor del sistema de arrastre de
la cadena (D) en el motor (tambor de embrague).
•
Las reculadas pueden ser rapidísimas y muy
violentas. La mayoría de las reculadas son pequeñas
y, por tanto, no siempre activan el freno de cadena.En
estos casos debe sujetarse la motosierra con fuerza,
sin soltarla.
•
La protección contra reculadas no sólo activa el freno
de cadena. También cumple otra función importante:
reduce el riesgo de que la mano izquierda toque la
cadena si el usuario suelta el mango delantero.
•
El modo de activación del freno de cadena, manual o
por inercia, depende de la fuerza de la reculada y de
la posición de la motosierra en relación al objeto con
el que toca el sector de riesgo de reculada de la
espada.
En reculadas fuertes y con el sector de riesgo de
reculada de la espada lo más lejos posible del
usuario, el freno de cadena está diseñado para ser
activado por su propio contrapeso (inercia) en el
sentido de reculada.
•
El freno de cadena debe estar activado cuando se
arranca la motosierra, para impedir que la cadena gire.
•
Utilice el freno de cadena como 'freno de
estacionamiento' al arrancar y para los traslados
cortos a fin de prevenir accidentes por contacto
involuntario de usted o el entorno con la cadena de
sierra en movimiento.No deje la motosierra conectada
con el freno de cadena activado por mucho tiempo. La
motosierra puede alcanzar una temperatura muy alta.
En las reculadas poco violentas, o al trabajar con el
sector de riesgo de reculada cerca del usuario, el
freno de cadena se activa manualmente con la mano
izquierda.
52 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
•
En posición de tala, la mano izquierda está en una
posición que permite la activación manual del freno de
Fiador del acelerador
El fiador del acelerador está diseñado para impedir la
activación involuntaria del acelerador. Cuando se oprime
el fiador (A) en el mango (= cuando se agarra el mango),
se desacopla el acelerador (B). Cuando se suelta el
mango, el acelerador y el fiador vuelven a sus posiciones
originales. Ambas funciones se efectúan con sistemas
independientes de muelles de retorno.Con esta posición,
el acelerador queda automáticamente bloqueado en
ralentí.
cadena.Con este agarre, cuando la mano izquierda está
colocada de forma que no puede influir en el movimiento
de la protección contra reculada, el freno de cadena sólo
se puede activar mediante la función de inercia.
¿Activará siempre mi mano el freno de
cadena en caso de reculada?
No. Hace falta una fuerza determinada para mover la
protección contra reculada hacia adelante. Si su mano
sólo roza la protección contra reculada o resbala sobre
ella, puede ocurrir que la fuerza no sea suficiente para
activar el freno de cadena. También debe agarrar con
firmeza la empuñadura de la motosierra cuando trabaja.Si
lo hace y se produce una reculada, puede ocurrir que no
suelte el agarre de la empuñadura delantera y que no
active el freno de cadena, o que el freno de cadena no se
active hasta que la sierra haya girado bastante. En casos
así puede suceder que el freno de cadena no tenga tiempo
de detener la cadena antes de que le toque a usted.
Captor de cadena
El captor de cadena está diseñado para captar las
cadenas que se sueltan o se rompen. Normalmente esto
se evita con el tensado correcto de la cadena (vea las
instrucciones bajo el título Montaje) y con un
mantenimiento adecuado de la espada y la cadena (vea
las instrucciones bajo el título Instrucciones generales de
trabajo).
Ello ocurre también en determinadas posturas de trabajo
que impiden que su mano llegue a la protección contra
reculada para activar el freno de cadena; por ejemplo,
cuando se sujeta la sierra en posición de tala.
¿Se activa siempre por inercia el freno de
cadena cuando se produce una reculada?
No. En primer lugar, su freno debe funcionar. Es fácil probar
el freno; vea las instrucciones del capítulo Control,
mantenimiento y servicio del equipo de seguridad de la
motosierra. Recomendamos que haga esta prueba antes
de empezar cada turno de trabajo. En segundo lugar, la
reculada debe tener la fuerza suficiente para activar el freno
de cadena. Si el freno de cadena fuera demasiado sensible,
se activaría constantemente, lo que sería molesto.
Protección de la mano derecha
La protección de la mano derecha, además de proteger
la mano cuando una cadena se suelta o se rompe, impide
que las ramas perjudiquen el agarre del mango posterior.
¿Me protegerá siempre el freno de
cadena contra daños si se produce una
reculada?
No. En primer lugar, su freno debe funcionar para
proporcionar la protección prevista. En segundo lugar, el
freno se debe activar tal como se describe arriba para
detener la cadena de sierra en una reculada. En tercer
lugar, el freno de cadena se puede activar, pero si la
espada está demasiado cerca de usted puede ocurrir que
el freno no tenga tiempo de reducir la velocidad y parar la
cadena antes de que la motosierra le toque.
Solamente usted y empleando una técnica de trabajo
correcta puede eliminar el efecto de reculada y los
riesgos que comporta.
115 13 80-96 Rev.3 2008-12-17
Spanish – 53
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
Sistema amortiguador de vibraciones
Silenciador
Su máquina incorpora un sistema amortiguador diseñado
para reducir al máximo posible las vibraciones y optimizar
la comodidad de uso.
El silenciador está diseñado para reducir al máximo
posible el nivel sonoro y para apartar los gases de escape
del usuario.
¡ATENCION! Los gases de escape del
motor están calientes y pueden contener
chispas que pueden provocar incendio.
Por esa razón, ¡nunca arranque la
máquina en interiores o cerca de
material inflamable!
El sistema amortiguador de vibraciones de la máquina
reduce la transmisión de vibraciones entre la parte del
motor/equipo de corte y la parte de los mangos de la
máquina. El cuerpo de la motosierra, incluyendo el
equipo de corte, va suspendido de la parte de los mangos
con un elemento antivibratorio.
En regiones de clima cálido y seco puede haber un riesgo
de incendio considerable. En países de estas regiones
hay normativas y requisitos legales de, por ejemplo,
equipar el silenciador con una red apagachispas
homologada.
El corte de maderas duras (la mayoría de los árboles
caducifolios) produce más vibraciones que el de maderas
blandas (la mayoría de las coníferas). El corte con un
equipo de corte desafilado o incorrecto (modelo incorrecto
o mal afilado) incrementa el nivel de vibraciones.
Cuando ajuste el engranaje, asegúrese de que está
insertado correctamente. Si es necesario, sírvase de una
llave inglesa para insertar o extraer el engranaje.
¡NOTA! El silenciador está muy caliente durante el
funcionamiento y después de parar. Esto también es
aplicable al funcionamiento en ralentí. Preste atención
al riesgo de incendio, especialmente al emplear la
máquina cerca de sustancias y/o gases inflamables.
¡ATENCION! La sobreexposición a las
vibraciones puede provocar problemas
circulatorios y dolencias de carácter
nervioso, especialmente en personas con
patologías circulatorias. Acuda a un
médico si nota síntomas corporales que
puedan relacionarse con la
!
¡ATENCION! No utilice nunca una
sobreexposición a las vibraciones. Son
ejemplos de tales síntomas la pérdida de
sensibilidad, el 'cosquilleo', las
motosierra sin silenciador o con el
silenciador defectuoso. Un silenciador
defectuoso puede incrementar
!
'punzadas', el dolor, la pérdida o reducción
de la fuerza normal o los cambios en el
color y la superficie de la piel. Estos
síntomas se presentan normalmente en
dedos, manos y muñecas. Los síntomas
pueden aumentar en temperaturas frías.
considerablemente el nivel de ruido y el
riesgo de incendio.Tenga a mano
herramientas para la extinción de
incendios. No utilice nunca una
motosierra sin red apagachispas o con
red apagachispas defectuosa si la
normativa del país exige este equipo.
Botón de parada
El botón de parada se utiliza para parar el motor.
Equipo de corte
Este capítulo describe cómo Ud., con un mantenimiento
correcto y utilizando el equipo de corte adecuado, podrá:
•
•
Reducir la propensión a las reculadas de la máquina.
Reduce la ocurrencia de salidas y roturas de la
cadena de sierra.
•
•
Proporciona un resultado de corte óptimo.
Aumentar la duración del equipo de corte.
54 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
•
Evita el aumento de los niveles de vibraciones.
Equipo de corte reductor de reculadas
Reglas básicas
¡ATENCION! Un equipo de corte
defectuoso o una combinación errónea
de espada/cadena de sierre aumentan el
riesgo de reculadas. Utilice solamente
las combinaciones de espada/cadena de
sierra recomendadas y siga las
•
¡Utilice solamente el equipo de corte
recomendado por nosotros! Vea las instrucciones
bajo el titular Datos técnicos
!
instrucciones.Vea las instrucciones bajo
el titular Datos técnicos
Las reculadas sólo puede evitarlas Ud. el usuario,
impidiendo que el sector de riesgo de reculada de la
espada toque algún objeto.
•
¡Mantenga los dientes cortantes de la cadena bien
y correctamente afilados! Siga nuestras
instrucciones y utilice el calibrador de limado
recomendado. Una cadena mal afilada o defectuosa
aumenta el riesgo de accidentes.
El efecto de las reculadas puede reducirse utilizando un
equipo de corte con reducción de reculada ”incorporada”,
así como con un afilado y mantenimiento correctos de la
cadena.
Espada
Cuanto más pequeño es el radio de punta, menor es la
propensión a la reculada.
Cadena
•
¡Mantenga la profundidad de corte correcta! Siga
nuestras instrucciones y utilice el calibrador de
profundidad recomendado. Una profundidad de
corte demasiado grande aumenta el riesgo de
reculada.
Una cadena de sierra consta de distintos eslabones que
se presentan en versión estándar y en versión reductora
de reculada.
¡IMPORTANTE! Ninguna cadena de sierra elimina el
riesgo de reculada.
¡ATENCION! Cualquier contacto con una
sierra de cadena en girando puede
causar daños muy graves.
!
•
¡Mantenga la cadena correctamente tensada! Con
un tensado insuficiente se incrementa el riesgo de
solturas de la cadena y se aumenta el desgaste de la
espada, la cadena y el piñón de arrastre.
Expresiones características de la espada y cadena
Para conservar la eficacia de todos los componentes de
seguridad del equipo de corte, debe sustituir las
combinaciones de espada/cadena de sierra gastadas o
dañadas por una espada y una cadena recomendadas
por Husqvarna. Vea las instrucciones del capítulo Datos
técnicos para información sobre las combinaciones de
espada/cadena de sierra que recomendamos.
Espada
•
¡Mantenga el equipo de corte bien lubricado y
efectúe el mantenimiento adecuado! Con una
lubricación insuficiente se incrementa el riesgo de
roturas de cadena y se aumenta el desgaste de la
espada, la cadena y el piñón de arrastre.
•
Longitud (pulgadas/cm)
•
Número de dientes en el cabezal de rueda (T).
•
Paso de cadena (=pitch) (pulgadas). El cabezal de
rueda de la espada y el piñón de arrastre de la cadena
de la motosierra deben adaptarse a la distancia entre
los eslabones de arrastre.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 55
INSTRUCCIONES GENERALES DE SEGURIDAD
•
•
•
Número de eslabones de arrastre (unidades). A cada
combinación de longitud de cadena, paso de cadena y
número de dientes del cabezal de rueda, le corresponde
un número determinado de eslabones de arrastre.
•
Una sierra de cadena bien afilada atraviesa por sí sola
la madera y produce virutas grandes y largas.
•
La parte cortante de una cadena de sierra se
denomina eslabón de corte, formado por un diente de
corte (A) y un talón de profundidad (B).La distancia en
altura entre ellos determina la profundidad de corte.
Ancho de la guía de la espada (pulgadas/mm). El
ancho de la guía de la espada debe estar adaptado al
ancho del eslabón de arrastre de la cadena.
Hay tres medidas a considerar para el afilado del diente
de corte.
1
Ángulo de afilado
Orificio para aceite de cadena y orificio para pasador
tensor de cadena. La espada debe estar adaptada al
diseño de la motosierra.
2
Ángulo de corte
Cadena
•
Paso de cadena (=pitch) (pulgadas)
3
4
Posición de la lima
•
Ancho del eslabón de arrastre (mm/pulgadas)
Número de eslabones de arrastre (unidades)
Diámetro de la lima redonda
Es muy difícil afilar correctamente una cadena de sierra sin
los accesorios adecuados. Por ello le recomendamos que
utilice nuestro calibrador de afilado. La plantilla garantiza
un afilado de la cadena de sierra para una reducción de la
reculada y una capacidad de corte óptimas.
•
Afilado y ajuste del talón de profundidad
de una cadena de sierra
Vea las instrucciones del capítulo Datos técnicos en lo
referente a los datos para el afilado de la cadena de su
motosierra.
Generalidades sobre el afilado de los dientes
cortantes
•
No corte nunca con una sierra roma. Es señal de sierra
roma cuando es necesario presionar el equipo de corte
a través de la madera y el que las virutas son muy
pequeñas. Una cadena de sierra muy roma no produce
virutas. El único resultado es polvo de madera.
¡ATENCION! La negligencia en seguir las
instrucciones de afilado aumenta
considerablemente la propensión a la
reculada de la cadena de sierra.
!
56 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
Afilado de dientes cortantes
Ajuste de la profundidad de corte
Para afilar dientes de corte se requiere una lima redonda
y un calibrador de afilado. Vea las instrucciones del
capítulo Datos técnicos en lo referente al diámetro de fila
redonda y el calibrador de afilado recomendados para la
cadena de su motosierra.
•
•
El ajuste de la profundidad de corte debe hacerse con
los dientes cortantes recién afilados.Recomendamos
ajustar la profundidad de corte después de cada
tercer afilado de la cadena de sierra. ¡ATENCIÓN!
Esta recomendación presupone que la longitud de los
dientes de corte no se ha reducido anormalmente.
Para ajustar la profundidad de corte se necesita una
lima plana y un calibrador de profundidad de corte.
Recomendamos utilizar nuestro calibrador de afilado
de profundidad para obtener la medida de profundidad
correcta y el ángulo correcto del talón de profundidad.
•
•
Compruebe que la cadena esté bien tensada. Con un
tensado insificiente, la cadena tiene inestabilidad
lateral, lo cual dificulta el afilado correcto.
•
Ponga el calibrador de afilado sobre la cadena de
sierra. En el envase del calibrador hay instrucciones
sobre su empleo. Utilice la lima plana para limar el
sobrante de la parte sobresaliente del talón de
profundidad. La profundidad de corte es correcta
cuando no se nota resistencia alguna al pasar la lima
sobre el calibrador.
Afile siempre desde el interior del diente hacia fuera.
En el retorno, suavice la presión de la lima. Primero,
afile todos los dientes de un lado y, luego, vuelva la
motosierra y afile los dientes del otro lado.
•
Afile todos los dientes a la misma longitud. Cuando
sólo queden 4 mm (0,16") de la longitud de diente, la
cadena está desgastada y debe cambiarse.
Tensado de la cadena
¡ATENCION! Una cadena
insuficientemente tensada puede
soltarse y ocasionar accidentes graves,
incluso mortales.
!
Generalidades sobre el ajuste de la profundidad de
corte
La cadena se alarga con la utilización. Por consiguiente,
es importante ajustar el equipo de corte para compensar
este cambio.
•
Al afilar el diente de corte se reduce la altura del talón
de profundidad (= profundidad de corte). Para
mantener una capacidad máxima de corte hay que
bajar el talón de profundidad al nivel recomendado.
En lo referente a la profundidad de corte de la cadena
de su motosierra, vea el capítulo Datos técnicos.
El tensado de la cadena debe controlarse cada vez que
se reposte combustible. ¡NOTA! Las cadenas nuevas
requieren un período de rodaje, durante el que debe
controlarse el tensado con mayor frecuencia.
En general, la cadena debe tensarse tanto como sea
posible, aunque debe ser posible girarla fácilmente con la
mano.
¡ATENCION! ¡Una profundidad de corte
excesiva aumenta la propensión a las
reculadas de la cadena!
!
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 57
INSTRUCCIONES GENERALES DE SEGURIDAD
435
•
Girar la manija a izquierdas para soltar la cubierta de
la espada.
•
Afloje la tuerca de la espada que fija la cubierta del
embrague/el freno de cadena. Utilice la llave
combinada. Luego, apriete la tuerca de la espada con
la mano, lo más fuerte que pueda.
•
Ajustar la tensión de la cadena, girando la rueda hacia
abajo (+) para aumentar la tensión y hacia arriba (-)
para reducirla.
•
Con la punta de la espada hacia arriba, tense la
cadena enroscando el tornillo tensor con la llave
combinada.Tense la cadena hasta que deje de colgar
en la parte inferior de la espada.
•
Con la llave combinada, apriete la tuerca de la espada
sujetando al mismo tiempo la punta de la espada.
Compruebe que la cadena de la motosierra pueda
girarse a mano con facilidad y que no cuelgue en la
parte inferior de la espada.
•
Apretar el acoplamiento de la espada, girando la
manija a derechas.
Entre nuestros modelos de motosierra hay diferentes
ubicaciones del tornillo del tensor de cadena. Vea el
capítulo Componentes de la máquina en lo referente a la
ubicación de este tornillo en su modelo.
435e, 440e
•
Cerrar la manija para fijar el tensado.
•
Aflojar la manija abriéndola.
58 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
INSTRUCCIONES GENERALES DE SEGURIDAD
Control de la lubricación de la cadena
Lubricación del equipo de corte
•
Controle la lubricación de la cadena cada vez que
reposte. Vea las instrucciones del capítulo
¡ATENCION! La lubricación insuficiente
del equipo de corte puede ocasionar
roturas de cadena, con el riesgo
consiguiente de accidentes graves e
incluso mortales.
Lubricación del cabezal de rueda de la espada.
!
Apunte la punta de la espada a unos 20 cm (8
pulgadas) de un objeto fijo y claro. Después de 1
minuto de funcionamiento a 3/4 de aceleración debe
verse una línea de aceite clara en el objeto.
Aceite para cadena de motosierra
Un aceite para cadena de motosierra ha de tener buena
adhesión a la cadena, así como buena fluidez tanto en
climas cálidos como fríos.
Como fabricantes de motosierras hemos desarrollado un
aceite para cadena óptimo que, gracias a su origen
vegetal, es también biodegradable. Recomendamos el
uso de nuestro aceite para obtener la mayor
conservación, tanto de la cadena de sierra como del
medio ambiente. Si nuestro aceite para cadena de
motosierra no es accesible, recomendamos usar aceite
para cadena común.
Si no funciona la lubricación de la cadena:
¡No utilizar nunca aceite residual! Es nocivo para
usted, la máquina y el medio ambiente.
•
•
•
Compruebe que el canal de aceite de cadena en la
espada esté abierto. Límpielo si es necesario.
¡IMPORTANTE! Si utiliza aceite vegetal para cadena de
sierra, desmonte y limpie la ranura de la espada y la
cadena de sierra antes del almacenamiento
prolongado. De no hacerlo, hay riesgo de que se oxide
el aceite de la cadena de sierra, con lo que la cadena se
vuelve rígida y el cabezal de rueda se atasca.
Repostaje de aceite para cadena de motosierra
Compruebe que la guía de la espada esté limpia.
Límpiela si es necesario.
•
Todos nuestros modelos de motosierra tienen
lubricación automática de la cadena. Algunos
modelos pueden obtenerse también con flujo de
aceite regulable.
•
El depósito de aceite de cadena y el depósito de
combustible están dimensionados para que se
termine el combustible antes de terminarse el aceite
de cadena.
Compruebe que el cabezal de rueda de la espada
gire con facilidad y que su orificio de lubricación esté
abierto. Limpie y lubrique si es necesario.
No obstante, para que esta función de seguridad sea
efectiva debe utilizarse el aceite de cadena de sierra
correcto (un aceite demasiado claro se termina antes
de que se termine el combustible), debe seguirse
nuestra recomendación de reglaje del carburador
(una mezcla demasiado pobre hace que el
combustible dure más que el aceite de cadena), y
deben seguirse nuestras recomendaciones de equipo
de corte (una espada demasiado larga requiere más
aceite lubricante).
Si la lubricación de la cadena no funciona después de
efectuar los controles y medidas anteriores, contacte a su
taller de servicio.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 59
INSTRUCCIONES GENERALES DE SEGURIDAD
Piñón de arrastre de la cadena
Espada
Controle a intervalos regulares:
El tambor del embrague lleva uno de los siguientes
piñones de arrastre de cadena:
•
Si se han formado rebabas en los lados de la espada.
Lime si es necesario.
A
B
Piñón Spur (piñón soldado en el tambor)
Piñón Rim (cambiable)
•
•
Si la guía de la espada presenta un desgaste
anormal. Cambie la espada si es necesario.
Compruebe regularmente el nivel de desgaste del piñón
de arrastre de la cadena y cámbielo si presenta un
desgaste anormal.El piñón de arrastre de la cadena debe
cambiarse cada vez que se cambie la cadena.
Si la punta de la espada presenta un desgaste
anormal o irregular. Si se ha formado una ”cavidad” al
final del radio de la punta, en la parte inferior de la
espada, es señal de que Ud. ha utilizado la máquina
con un tensado de cadena insuficiente.
Lubricación del cojinete de agujas
Ambos tipos de piñón de accionamiento de cadena tienen
en el eje saliente un cojinete de agujas que debe
lubricarse a intervalos regulares (1 vez por semana).
¡NOTA! Utilice grasa para cojinetes de buena calidad o
aceite para motor.
•
Para obtener una duración óptima, la espada debe
girarse regularmente.
Vea las instrucciones del apartado ”Mantenimiento,
Lubricación de cojinetes de agujas”.
Control del desgaste del equipo de corte
¡ATENCION! La mayoría de los
accidentes con la motosierra se producen
cuando la cadena toca al usuario.
!
Controle diariamente la cadena para comprobar si:
Utilice el equipo de protección personal.
Vea las instrucciones bajo el título
Equipo de protección personal.
Evite los trabajos para los que no se
sienta suficientemente capacitado.Vea las
instrucciones bajo los títulos Equipo de
protección personal, Medidas preventivas
de reculadas, Equipo de corte e
•
•
•
Hay grietas visibles en los remaches y eslabones.
La cadena está rígida.
Instrucciones generales de trabajo.
Evite situaciones con riesgo de reculada.
Vea las instrucciones bajo el título
Equipo de seguridad de la máquina.
Los remaches y eslabones presentan un desgaste
anormal.
Deseche la cadena de sierra si concuerda con alguno o
varios de los puntos anteriores.
Utilice el equipo de corte recomendado y
controle su estado.Vea las instrucciones
bajo el título Instrucciones generales de
trabajo.
Para comprobar el desgaste de la cadena que utiliza, le
recomendamos que la compare con una cadena nueva.
Cuando sólo queden 4 mm (0.16 de pulgada) de longitud
de diente cortante, la cadena está gastada y debe
cambiarse.
Compruebe el funcionamiento de las
piezas de seguridad de la motosierra.
Vea las instrucciones bajo los títulos
Instrucciones generales de trabajo e
Instrucciones generales de seguridad.
60 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MONTAJE
cadena debe tensarse hasta que deje de colgar en la
parte inferior de la espada.
Montaje de la espada y la cadena
¡ATENCION! Para manipular la cadena
deben utilizarse guantes protectores.
!
La cadena está correctamente tensada cuando no cuelga
floja en el lado inferior de la espada y puede girarse
fácilmente con la mano. Apriete la tuerca de la espada
con la llave combinada, manteniendo al mismo tiempo la
punta de la espada dirigida hacia arriba.
435
Compruebe que no esté activado el freno de cadena
empujando la protección contra reculadas del freno de
cadena hacia el mango delantero.
Desenrosque la tuerca de la espada y desmonte la
carcasa del embrague (el freno de cadena). Saque la
protección de transporte (A).
El tensado de una cadena nueva debe controlarse con
frecuencia, hasta que se haya hecho el rodaje. Controle
el tensado regularmente. Una cadena correcta significa
buena capacidad de corte y larga duración.
Monte la espada sobre el perno de la espada. Coloque la
espada en la posición posterior extrema. Coloque la
cadena sobre el piñón de arrastre y en la guía de la
espada. Empiece con la parte superior de la cadena.
435e, 440e
Compruebe que no esté activado el freno de cadena
empujando la protección contra reculadas del freno de
cadena hacia el mango delantero.
Compruebe que los filos de los eslabones de corte estén
orientados hacia delante en la parte superior de la
espada.
Monte la cubierta del embrague y no olvide poner el
vástago de tensado de cadena en el orificio de la espada.
Compruebe que los eslabones de arrastre de la cadena
encajen en el piñón de arrastre y que la cadena esté bien
colocada en la guía de la espada. Apriete la tuerca de la
espada con los dedos.
Tense la cadena enroscando en el sentido de las agujas
del reloj el tornillo de tensado con la llave combinada. La
115 13 80-96 Rev.3 2008-12-17
Spanish – 61
Download from Www.Somanuals.com. All Manuals Search And Download.
MONTAJE
Suelte la rueda tensora de cadena y quite la cubierta del
embrague (freno de cadena). Quite la protección de
transporte. (A)
con la llave combinada, sujetando al mismo tiempo la
punta de la espada.
El tensado de una cadena nueva debe controlarse con
frecuencia, hasta que se haya hecho el rodaje. Controle
el tensado regularmente. Una cadena correcta significa
buena capacidad de corte y larga duración.
Monte la espada en los pernos. Sitúela en la posición
posterior extrema. Monte la cadena en el piñón de
arrastre y la guía de la espada. Empiece con la parte
superior de la cadena.
Montaje del apoyo de corteza
Para montar el apoyo de corteza, consulte a su taller de
servicio local.
Compruebe que los filos de los eslabones de corte estén
orientados hacia delante en la parte superior de la
espada.
Monte la cubierta del embrague y no olvide poner el
vástago de tensado de cadena en el orificio de la espada.
Compruebe que los eslabones de arrastre de la cadena
encajen en el piñón de arrastre y que la cadena esté bien
colocada en la guía de la espada.
Tensar la cadena girando la rueda hacia abajo (+). La
cadena se debe tensar hasta que no tenga deflexión en
la parte inferior de la espada.
La cadena está correctamente tensada cuando no cuelga
en la parte inferior de la espada y puede girarse
fácilmente con la mano. Apriete las tuercas de la espada
62 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANIPULACION DEL COMBUSTIBLE
Mezcla
Carburante
1:50 (2%) para todos los motores.
Aclaración! La máquina tiene motor de dos tiempos, por
lo que debe utilizarse siempre una mezcla de gasolina
con aceite para motores de 2 tiempos. Es importante
medir con precisión la cantidad de aceite que se mezcla
para conseguir la proporción de mezcla adecuada. Al
mezclar pequeñas cantidades de combustible, incluso los
pequeños errores en la cantidad de aceite tienen una
gran incidencia en la proporción de mezcla.
Aceite para motores
de dos tiempos, litros
Gasolina, litros
2% (1:50)
0,10
5
10
0,20
15
0,30
20
0,40
¡ATENCION! Para hacer la mezcla,
compruebe que haya buena ventilación.
Gal EE.UU.
Oz fl EE.UU.
2 1/2
!
1
2 1/2
5
6 1/2
Gasolina
12 7/8
Mezcla
•
•
Utilice gasolina sin plomo o gasolina con plomo de
alta calidad.
¡NOTA! En los motores con catalizador debe
usarse mezcla de gasolina sin plomo y aceite. La
gasolina con plomo avería el catalizador, cuya función
desaparece. El tapón de depósito verde en
motosierras con catalizador indica que sólo se debe
usar gasolina sin plomo.
•
•
El octanaje mínimo recomendado es 87
•
•
Siempre haga la mezcla de gasolina y aceite en un
recipiente limpio, homologado para gasolina.
Primero, ponga la mitad de la gasolina que se va a
mezclar. Luego, añada todo el aceite y agite la
mezcla. A continuación, añada el resto de la gasolina.
Agite bien la mezcla de combustible antes de ponerla
en el depósito de combustible de la máquina.
No mezcle más combustible que el necesario para
utilizar un mes como máximo.
((RON+MON)/2). Si se utiliza gasolina de octanaje
inferior a 87, se puede producir el efecto “clavazón”.
Esto produce un aumento de la temperatura del motor
y de la carga sobre los cojinetes, fenómenos que
pueden causar averías graves del motor.
•
•
•
Para trabajos con régimen alto continuado (por
ejemplo, para desramar), se recomienda un octanaje
más alto.
Combustible ecológico
Si no se ha utilizado la máquina por un tiempo
prolongado, vacíe el depósito de combustible y límpielo.
HUSQVARNA recomienda usar gasolina ecológica
(combustible de alquilato); bien gasolina premezclada
Aspen para motores de dos tiempos, o gasolina ecológica
para motores de cuatro tiempos mezclada con aceite
para motores de dos tiempos según se indica abajo.
Tenga en cuenta que puede ser necesario ajustar el
carburador cuando se cambia el tipo de combustible (vea
las instrucciones del capítulo Carburador).
Aceite para cadena
•
Para lubricar se recomienda un aceite especial (aceite
para lubricar cadenas) con buena aptitud adherente.
Rodaje
No manejar la máquina a revoluciones demasiado altas
por periodos prolongados durante las primeras diez horas.
Aceite para motores de dos tiempos
•
•
•
No utilice nunca aceite residual. Puede ocasionar
averías en la bomba de aceite, la espada y la cadena.
Es importante utilizar un aceite adecuado para la
temperatura ambiente (con la viscosidad correcta).
Con temperaturas bajo cero, algunos aceites se
espesan.Ello puede causar sobrecargas en la bomba
de aceite, con averías subsiguientes de las piezas de
la bomba.
•
Para un resultado y prestaciones óptimos, utilice
aceite para motores de dos tiempos HUSQVARNA,
especialmente fabricado para motores de dos
tiempos refrigerados por aire.
•
•
No utilice nunca aceite para motores de dos tiempos
fuera borda refrigerados por agua (llamado outboard
oil), con designación TCW.
•
Para la selección de aceite lubricante de cadena,
consulte con su taller de servicio.
No utilice nunca aceite para motores de cuatro tiempos.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 63
MANIPULACION DEL COMBUSTIBLE
•
Antes de arrancar, aparte la máquina a 3 m como
mínimo del lugar de repostaje.
Repostaje
¡ATENCION! Las siguientes medidas
preventivas reducen el riesgo de
incendio:
!
No fume ni ponga objetos calientes
cerca del combustible.
Apague el motor y deje que se enfríe
unos minutos antes de repostar.
•
Nunca arranque la máquina:
1
Si ha derramado sobre la máquina combustible o
aceite para cadena.Seque cualquier residuo y espere
a que se evaporen los restos de combustible.
Para repostar, abra despacio la tapa del
depósito de combustible para evacuar
lentamente la eventual sobrepresión.
2
3
Si se salpicó el cuerpo o las ropas, cambie de ropas.
Lave las partes del cuerpo que han entrado en
contacto con el combustible. Use agua y jabón.
Después de repostar, apriete bien la tapa
del depósito de combustible.
Si hay fugas de combustible en la máquina.
Compruebe regularmente si hay fugas en la tapa del
depósito o en los conductos de combustible.
Antes de arrancar, aparte siempre la
máquina del lugar de repostaje.
¡ATENCION! No utilice nunca una
máquina con daños visibles en la
protección de bujía y el cable de
encendido. Hay riesgo de generación de
chispas, que pueden causar incendios.
Seque minuciosamente alrededor de las tapas de los
depósitos. Limpie regularmente los depósitos de
combustible y de aceite para cadena. Cambie el filtro de
combustible una vez al año como mínimo.La suciedad en
los depósitos produce perturbaciones del
funcionamiento. Asegúrese de que el combustible esté
bien mezclado, agitando el recipiente antes de repostar.
Las capacidades de los depósitos de combustible y aceite
para cadena están adaptadas entre sí. Por consiguiente,
haga el repostaje de ambos al mismo tiempo.
!
Transporte y almacenamiento
•
Almacene la motosierra y el combustible de forma que
no haya riesgo de que los eventuales vapores y fugas
entren en contacto con chispas o llamas.Por ejemplo,
cerca de máquinas eléctricas, motores eléctricos,
contactos/interruptores eléctricos, calderas de
calefacción o similares.
•
•
Para el almacenamiento del combustible deben
utilizarse recipientes especiales homologados.
En caso de almacenamiento o transporte de la
motosierra por tiempo prolongado, deberán vaciarse
los depósitos de combustible y aceite para cadena.
Consulte con la gasolinera más cercana sobre qué
hacer con el combustible y aceite de cadena sobrantes.
¡ATENCION! El combustible y los
vapores de combustible son muy
inflamables. Proceda con cuidado en la
manipulación del combustible y el aceite
de cadena.Tenga en cuenta el riesgo de
incendio, explosión e inhalación.
•
•
Antes del almacenaje prolongado, limpie bien la
máquina y haga el servicio completo.
!
La protección de transporte del equipo de corte debe
estar siempre montada para el transporte y
almacenamiento de la máquina, a fin de evitar el
contacto fortuito con la cadena aguda. Una cadena
inmóvil también puede causar daños graves al
usuario u otras personas que llegan a la cadena.
Seguridad en el uso del
combustible
•
Quite el capuchón de encendido de la bujía. Active el
freno de cadena.
•
No reposte nunca la máquina con el motor en marcha.
Almacenamiento prolongado
•
Procure que haya buena ventilación durante el
repostaje y la mezcla de combustible (gasolina y
aceite para motores de 2 tiempos).
Vacíe los depósitos de combustible y aceite en un lugar
bien ventilado. Guarde el combustible en bidones
homologados y en un lugar seguro. Monte la protección
de la espada. Limpie la máquina. Vea las instrucciones
del capítulo Programa de mantenimiento.
64 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
ARRANQUEY PARADA
(cuando se conecten los ganchos de arranque). Luego,
dé tirones rápidos y fuertes hasta que el motor arranque.
Arranque y parada
Oprimir inmediatamente el estrangulador rojo (4):
Cuando el motor arranque, oirá una especie de soplido y
entonces deberá oprimir inmediatamente el
estrangulador rojo.
¡ATENCION! Antes de arrancar, observe
lo siguiente:
!
El freno de cadena debe estar aplicado
cuando se arranca la motosierra, para
reducir el riesgo de contacto con la cadena
en movimiento al ponerse en marcha.
Agarre la empuñadura de arranque (5): Reponga con
firmeza el cordón a su posición inicial y repita el intento
hasta que el motor arranque.
Motor caliente
No ponga en marcha la motosierra sin
haber montado antes la espada, la
cadena y todas las cubiertas. De otro
modo, el embrague puede zafar y
ocasionar daños personales.
Posición de arranque (1): Para la función combinada de
estrangulamiento/aceleración de arranque en caliente,
mueva el estrangulador tirando del mando rojo hacia
fuera y hacia arriba.
Bomba de combustible (2): Presione varias veces la
membrana de goma de la bomba de combustible hasta que
empiece a llenarse de combustible (6 veces como mínimo).
No es necesario llenar completamente la membrana.
Ponga la máquina sobre una superficie
estable. Asegúrese de tener buena
estabilidad y de que la cadena no pueda
tocar ningún objeto.
Oprimir inmediatamente el estrangulador rojo (4): De
esta manera se desactiva el estrangulador, que no es
necesario para el arranque en caliente de la motosierra.
Sin embargo, el movimiento del interruptor de arranque/
parada habrá provocado un ralentí alto, lo que facilita el
arranque en caliente.
Asegúrese de que no haya terceros
desautorizados en la zona de trabajo.
Nunca enrosque el cordón de arranque
alrededor de la mano.
Agarre la empuñadura de arranque (5): Agarre el
mango delantero con la mano izquierda. Pise la parte
inferior del mango trasero con el pie derecho y presione
la motosierra contra el suelo.
Arranque
El freno de cadena debe estar activado al poner en
marcha la motosierra. Active el freno moviendo la
protección contra reculadas hacia delante.
Motor frío
Agarre la empuñadura de arranque con la mano derecha
y tire lentamente del cordón hasta que note resistencia
(cuando se conecten los ganchos de arranque). Luego,
dé tirones rápidos y fuertes hasta que el motor arranque.
Posición de arranque (1): Sitúe el interruptor de
arranque / parada en la posición de estrangulamiento
tirando del mando rojo hacia arriba y hacia fuera.
Bomba de combustible (2): Presione varias veces la
membrana de goma de la bomba de combustible hasta que
empiece a llenarse de combustible (6 veces como mínimo).
No es necesario llenar completamente la membrana.
Dado que el freno de cadena todavía está activado, se
deben bajar las revoluciones del motor lo antes posible a
ralentí, y esto se logra desconectando el fiador contra
aceleraciones involuntarias. Para desconectarlo, acelere
ligeramente el activador de aceleraciones involuntarias.
De ese modo, se evita un desgaste innecesario del
embrague, del tambor del embrague y de la cinta de
freno. Deje funcionar la máquina en ralentí unos
segundos antes de acelerar plenamente.
A
2
1
Agarre el mango delantero con la mano izquierda. Pise la
parte inferior del mango trasero con el pie derecho y
presione la motosierra contra el suelo.
En la parte trasera (A) de la motosierra hay un
recordatorio de arranque simplificado, con figuras que
describen cada paso.
Agarre la empuñadura de arranque (3): agarre la
empuñadura de arranque con la mano derecha y tire
lentamente del cordón hasta que note resistencia
115 13 80-96 Rev.3 2008-12-17
Spanish – 65
Download from Www.Somanuals.com. All Manuals Search And Download.
ARRANQUEY PARADA
¡NOTA! No extraiga el cordón de arranque al máximo, y
no suelte la empuñadura de arranque si ha extraído todo
el cordón. Ello puede ocasionar averías en la máquina.
•
Observe el entorno y asegúrese de que no haya riesgo
de tocar a personas o animales con el equipo de corte.
•
Sujete siempre la motosierra con ambas manos.
Agarre la empuñadura trasera con la mano derecha y
la empuñadura delantera con la mano izquierda.
Todos los usuarios, diestros o zurdos, deben usar
este agarre. Agarre con firmeza, con todos los dedos
alrededor de las empuñaduras de la motosierra.
Aclaración! Para poner el freno de cadena en su
posición inicial, mueva la protección contra
reculadas hacia la empuñadura del mango. Ahora, la
motosierra está lista para funcionar.
¡ATENCION! La inhalación prolongada
de los gases de escape del motor, la
neblina de aceite de cadena y el polvo de
serrín puede poner en riesgo la salud.
!
•
Para liberar el freno de cadena, mueva hacia atrás
(en dirección a la empuñadura del mango) la
protección contra reculadas con la inscripción
«TIRAR HACIA ATRÁS PARA REINICIAR».
•
Nunca ponga en marcha la motosierra sin haber
montado antes correctamente la espada, la cadena y
todas las cubiertas.Vea las instrucciones bajo el título
Montaje. Sin la espada y la cadena montadas en la
motosierra, el embrague se puede soltar y causar
daños graves.
Parada
•
El freno de cadena debe estar aplicado cuando se
arranca la motosierra. Vea las instrucciones del
capítulo Arranque y parada. No arranque nunca la
motosierra agarrando el cordón de arranque y
soltando la máquina. Este método es muy peligroso
porque se pierde fácilmente el control de la
motosierra.
El motor se arranca presionando el mando de arranque/
parada.
¡NOTA! El contacto de arranque/parada retorna
automáticamente a la posición de marcha. Por
consiguiente, para evitar el arranque involuntario hay que
quitar siempre el capuchón de encendido de la bujía
cuando se abandona la máquina.
•
No ponga nunca en marcha la máquina en interiores.
Tenga en cuenta el riesgo de inhalación de los gases
de escape del motor.
66 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
Reglas básicas de seguridad
Antes de utilizar la máquina:
1
•
Observe el entorno para:
Comprobar que no hayan personas, animales, etc.,
que puedan influir en su control de la máquina.
•
Impedir que eventuales personas o animales puedan
entrar en contacto con la cadena o sean alcanzadas
o lesionadas por un árbol derribado.
,
1
2
3
4
Compruebe que el freno de cadena funcione
correctamente y no esté dañado.
Compruebe que la protección trasera de la mano
derecha no esté dañada.
Compruebe que el fiador contra aceleraciones
involuntarias funcione correctamente y no esté dañado.
¡NOTA! Siga las instrucciones mencionadas arriba y no
utilice la motosierra sin que haya alguien a quien recurrir
en caso de accidente.
Compruebe que el botón de parada funciona bien y
está en buen estado.
5
6
Compruebe que todos los mangos estén libres de aceite.
2
No trabaje en condiciones atmosféricas
Compruebe que el sistema de amortiguación de
vibraciones funcione y no esté dañado.
desfavorables como niebla, lluvia intensa, tempestad,
frío intenso, etc. El trabajo con mal tiempo es fatigoso
y puede crear circunstancias peligrosas, como
terreno resbaladizo, cambio imprevisto de la dirección
de derribo de los árboles, etc.
7
8
Compruebe que el silenciador esté firmemente
montado y en buenas condiciones.
Compruebe que todas las piezas de la motosierra
estén bien apretadas, no presenten daños y estén
presentes.
3
4
Proceda con sumo cuidado en el corte de ramas
pequeñas y evite cortar arbustos (= varias ramas al
mismo tiempo). Después del corte, las ramas
pequeñas pueden atascarse en la cadena, ser
lanzadas hacia Ud. y herirle de gravedad.
9
Compruebe que el retén de cadena esté montado y
en buenas condiciones.
10 Controle el tensado de la cadena.
Compruebe que pueda caminar y mantenerse de pie
con seguridad. Vea si hay eventuales impedimentos
para desplazamientos imprevistos (raíces, piedras,
ramas, fosos, zanjas, etc.). Proceda con sumo
cuidado al trabajar en terreno inclinado.
Instrucciones generales de
trabajo
¡IMPORTANTE!
Este capítulo se refiere a las reglas de seguridad
básicas para el trabajo con una motosierra. En ningún
caso, su contenido podrá sustituir a los conocimientos,
formación y experiencia práctica de un profesional. Por
consiguiente, cuando no esté seguro de cómo utilizar la
máquina, consulte a un experto. Diríjase a la tienda
donde compró la motosierra, al taller de servicio o a un
usuario de motosierras experto. ¡Evite los trabajos para
los que no se sienta suficientemente cualificado!
No utilice la motosierra hasta que haya comprendido el
significado de las reculadas y la forma de evitarlas.Vea
las instrucciones bajo el título Medidas preventivas de
las reculadas.
5
Sea sumamente cuidadoso al cortar en árboles en
tensión. Un árbol en tensión puede, tanto antes como
después de terminar de cortar, volver a su posición
normal. Si Ud. o el corte están mal ubicados, el árbol
puede golpearlo a Ud.o a la máquina y hacerle perder
el control. Las dos situaciones pueden ocasionar
daños personales graves.
No utilice la motosierra hasta que haya comprendido la
diferencia entre las técnicas de corte con la parte
superior y la parte inferior de la espada. Vea las
instrucciones de los capítulos Medidas preventivas de
las reculadas y Equipo de seguridad de la máquina.
Utilice el equipo de protección personal. Vea las
instrucciones bajo el título Equipo de protección personal.
115 13 80-96 Rev.3 2008-12-17
Spanish – 67
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
Controle la pieza de trabajo. Si las piezas de trabajo
que sierra son pequeñas y ligeras, pueden atascarse
en la cadena de sierra y ser lanzadas contra usted.
Esto, aunque no es necesariamente peligroso, puede
sorprenderle y hacerle perder el control de la
motosierra.No sierre nunca troncos apilados ni ramas
sin separarlos antes. Sierre solamente los troncos de
trozo en trozo. Aparte los trozos aserrados para
mantener segura su zona de trabajo.
6
Para los desplazamientos, bloquee la cadena con el
freno de cadena y pare el motor. Lleve la motosierra
con la espada y cadena orientadas hacia atrás. Para
los desplazamientos largos y los transportes utilice
siempre la protección de la espada.
7
Cuando ponga la motosierra en el suelo, bloquee la
cadena de sierra con el freno de cadena y no pierda
de vista la motosierra. Para el 'estacionamiento
prolongado', se debe parar el motor.
4
No utilice nunca la motosierra por encima de los
hombros y evite cortar con la punta de la
motosierra. ¡No utilice nunca la motosierra con
una sola mano!
Reglas básicas
1
Entendiendo las implicaciones y causas de la
reculada, Ud. puede reducir o eliminar sorpresas que
incrementen el riesgo de accidente. La mayoría de
reculadas son pequeñas, aunque algunas son
rapidísimas y muy violentas.
2
Sujete siempre la motosierra con firmeza, con la
mano derecha en el mango trasero y la mano
izquierda en el mango delantero, agarrando los
mangos con todos los dedos. Este agarre deben
utilizarlo todos los usuarios, incluso los zurdos. Este
agarre es la mejor forma de reducir el efecto de una
reculada y, al mismo tiempo, mantener el control de la
motosierra. ¡No suelte los mangos!
5
Para obtener máximo control de la motosierra, es
necesario adoptar una posición estable. No trabaje
nunca subido a una escalera, trepado a un árbol o en
una posición que carezca de una base firme.
3
La mayoría de los accidentes por reculada se
producen al desramar. Procure trabajar con una
postura estable y que en el suelo no hayan objetos
que puedan hacerle tropezar y perder el equilibrio.
Si se trabaja con negligencia, el sector de riesgo de
reculada de la espada puede tocar involuntariamente
una rama, un árbol u otro objeto y producir una reculada.
6
7
Corte con velocidad de cadena alta, acelerando al
máximo.
Para cortar con la parte superior de la espada, en
sentido ascendente desde la parte inferior del objeto a
cortar, proceda con muchísimo cuidado. Al trabajar
con esta técnica, llamada de cadena impelente, la
cadena empuja la motosierra hacia atrás, hacia el
68 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
usuario.Si la cadena de sierra se atasca, la motosierra
Designaciones
puede ser lanzada hacia atrás contra usted.
Tronzado = denominación genérica del corte transversal
de la madera.
Desramado = corte de las ramas de un árbol talado.
Partición = rotura del objeto que se corta antes de
concluir el corte.
Para los trabajos de tronzado deben tenerse en
cuenta cinco factores muy importantes:
8
Si el usuario no resiste la fuerza de la motosierra,
puede ocurrir que ésta retroceda tanto que el sector
de riesgo de reculada de la espada toque el árbol y se
produzca una reculada.
1
El equipo de corte no debe quedar apretado en el
surco.
2
3
El objeto que se corta no debe partirse.
El corte con la parte inferior de la espada, en sentido
descendente desde la parte superior del objeto a cortar,
se denomina de corte con cadena tirante. La motosierra
es tirada hacia el árbol y el canto delantero del cuerpo
se apoya contra el tronco. Con esta técnica de cadena
tirante, el usuario controla mejor la motosierra y la
situación del sector de riesgo de reculada de la espada.
Durante el tronzado y después del mismo, la cadena
de la sierra no debe tocar el suelo ni objeto alguno.
4
¿Hay riesgo de reculada?
9
Siga las instrucciones de afilado y mantenimiento de
la espada y la cadena. Al cambiar la espada y la
cadena sólo deben utilizarse las combinaciones
recomendadas por nosotros. Vea las instrucciones
bajo los títulos Equipo de corte y Datos técnicos.
5
¿Puede la configuración del terreno y el entorno influir
en su estabilidad y seguridad para caminar y
mantenerse de pie?
Técnica básica de corte
¡ATENCION! No utilice nunca una
El atasco de la cadena y la partición del objeto de corte
pueden deberse a dos factores: el apoyo del objeto antes
y después del tronzado, y si el objeto a cortar está tenso.
motosierra agarrándola solamente con
una mano. Una motosierra no se
controla con seguridad con una mano.
Agarre con fuerza y firmeza las
!
En la mayoría de casos, estos factores pueden evitarse
efectuando el tronzado en dos etapas: por arriba y por
abajo. Así se neutraliza la propensión del objeto a cortar
a apretar la cadena o a partirse.
empuñaduras con ambas manos.
Generalidades
•
•
¡Para cortar, utilice siempre la aceleración máxima!
Después de cada corte de sierra, suelte el acelerador
y deje el motor en vacío (la aceleración máxima
prolongada sin carga, es decir sin que el motor tenga
la resistencia de la cadena en el aserrado, produce
avería grave del motor).
¡IMPORTANTE! Si la cadena se atasca en el surco:
¡Pare el motor! No intente sacar la motosierra por la
fuerza. Si lo hace, puede accidentarse con la cadena
cuando se suelta repentinamente la motosierra. Para
soltar la motosierra, utilice una palanca.
•
•
Corte descendente = con cadena ”tirante”.
Corte ascendente = con cadena ”impelente”.
A continuación, se indica un listado teórico de la forma de
tratar las situaciones más comunes con que puede
enfrentarse un usuario de motosierra.
La técnica con cadena ”impelente” supone un mayor
riesgo de reculada. Vea las instrucciones bajo el título
Medidas preventivas de las reculadas.
115 13 80-96 Rev.3 2008-12-17
Spanish – 69
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
Desramado
Gire el tronco para cortar el tercio restante desde arriba.
Para cortar ramas gruesas deben aplicarse los mismos
principios que para el tronzado.
Corte las ramas difíciles por partes.
2
1
El tronco está apoyado en un extremo. Gran riesgo de
partición.
3
Empiece cortando desde abajo (aproximadamente 1/3
del diámetro del tronco).
Tronzado
Termine el corte desde arriba, hasta que se encuentren
los dos surcos.
¡ATENCION! No intente nunca serrar
troncos apilados ni dos troncos que
!
están muy juntos. Estos métodos
incrementan drásticamente el riesgo de
reculada, que comportan riesgo de
daños personales graves y peligro de
muerte.
El tronco está apoyado en ambos extremos. Gran
riesgo de atasco de la cadena.
Si hay una pila de troncos, se debe separar de ella cada
tronco que se va a cortar, colocarlo en un soporte para
serrar guiadera y cortarlo por separado.
Aparte los trozos cortados de la zona de trabajo. Si los
deja en la zona de trabajo, aumenta el riesgo de reculada
por equivocación y el riesgo de perder el equilibrio
cuando trabaja.
Empiece cortando desde arriba (aproximadamente 1/3
del diámetro del tronco).
Termine el corte desde abajo, hasta que se encuentren
los dos surcos.
El tronco en el suelo. No hay riesgo de atasco de la
cadena o de partición del objeto de corte. Sin embargo,
hay un riesgo considerable de que la cadena toque el
suelo después del corte.
Técnica de tala
¡IMPORTANTE! La tala de árboles requiere mucha
experiencia. Un usuario de motosierra inexperto no
debe talar árboles.¡Evite los trabajos para los que no se
considere suficientemente capacitado!
Corte desde arriba todo el tronco. Al final del corte,
proceda con cuidado para evitar que la cadena toque el
suelo. Mantenga la aceleración máxima y esté alerta a lo
que va a pasar.
Distancia de seguridad
La distancia de seguridad entre el árbol a talar y el lugar
de trabajo más cercano debe ser de 2,5 longitudes de
árbol. Asegúrese de que no haya nadie en esta ”zona de
riesgo” antes de la tala y durante la misma.
Si es posible (¿puede girarse el tronco?), termine el corte
a 2/3 del diámetro del tronco.
70 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
Dirección de derribo
Corte de ramas bajas y camino de retirada
El derribo tiene por objeto la colocación del árbol de
forma que el desramado y tronzado subsiguientes
puedan efectuarse en un terreno lo más ”fácil” posible. El
talador debe poder caminar y mantenerse de pie con
seguridad.
Desrame el ronco hasta la altura del hombro. Es más
seguro trabajar de arriba a abajo y tener el tronco entre
usted y la motosierra.
Cuando haya decidido en qué dirección quiere derribar el
árbol, debe considerar la dirección natural de caída del
mismo.
Ésta depende de varios factores:
•
•
•
•
•
•
Inclinación
Torcimiento
Dirección del viento
Concentración de las ramas
Peso de la nieve, si la hay
Limpie la vegetación que hay alrededor del árbol y elimine
los eventuales obstáculos (piedras, ramas, huecos, etc.)
para tener preparado un camino de retirada cuando
empiece a caer el árbol. El camino de retirada debe estar
a unos 135°, oblicuamente hacia atrás, de la dirección de
derribo prevista.
Obstáculos dentro del alcance del árbol: como otros
árboles, cables eléctricos, paredes y edificios.
•
Compruebe si el tronco tiene daños o podredumbre,
que aumentan la probabilidad de que el árbol se
rompa y empiece a caer antes de lo previsto.
1
3
2
1
1
Una vez considerados estos factores, puede verse
obligado a dejar que el árbol caiga en su dirección
natural, ya que es imposible, o demasiado arriesgado,
intentar colocarlo en la dirección decidida en un principio.
2
Otro factor muy importante, que no afecta a la dirección
de derribo pero sí a su seguridad personal, es el control
de que el árbol no tenga ramas dañadas o ”muertas” que
puedan romperse por sí solas y dañarle a Ud. durante la
tala.
1
2
3
Zona de riesgo
Vía de retirada
Dirección de derribo
Tala
Ante todo, debe evitarse que el árbol derribado se
atasque en otro árbol. Es muy peligroso retirar un árbol
atascado y hay un elevado riesgo de accidente. Vea las
instrucciones bajo el título Tratamiento de una tala fallida.
¡ATENCION! ¡Desaconsejamos a los
usuarios insuficientemente cualificados
que talen árboles con espada de longitud
más pequeña que el diámetro del tronco
a cortar!
La tala se hace con tres cortes. Se empieza con el corte
de indicación, compuesto por un corte superior y un corte
inferior; y se termina con el corte de derribo. Con la
ubicación correcta de estos cortes puede controlarse con
gran exactitud la dirección de derribo.
Corte de indicación
Para cortar el corte de indicación se empieza con el corte
superior.Oriente las marcas de dirección de tala (1) hacia
un objeto del terreno en el sentido en que se quiere abatir
el árbol (2). Sitúese en el lado derecho del árbol, detrás
de la sierra, y corte con cadena tirante.
¡IMPORTANTE! En momentos críticos de la tala
deberán levantarse los protectores auriculares apenas
termine el aserrado, a fin de poder advertir ruidos y
señales de advertencia.
115 13 80-96 Rev.3 2008-12-17
Spanish – 71
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
Luego, efectúe el corte inferior, que debe terminar
exactamente donde terminó el corte superior.
pequeña o se atraviesa al cortar, o si los cortes de
indicación y derribo están mal situados.
Cuando están terminados los cortes de indicación y de
derribo, el árbol debe empezar a caer; bien por sí solo, o
con ayuda de la cuña de derribo o de la barra
desgajadora.
La profundidad del corte de indicación debe ser igual a 1/
4 del diámetro del tronco, y el ángulo entre los cortes
superior e inferior debe ser de 45° como mínimo.
La convergencia de ambos cortes se denomina línea de
corte de indicación. La línea de corte de indicación debe
ser perfectamente horizontal y formar un ángulo recto
(90°) con la dirección de derribo elegida.
Recomendamos emplear una longitud de espada mayor
que el diámetro del tronco para que los cortes de derribo
e indicación se puedan hacer con un ”corte sencillo”.Vea
las instrucciones del capítulo Datos técnicos en lo
referente a las longitudes de espada recomendadas para
su modelo de motosierra.
Corte de derribo
El corte de derribo se hace en el lado opuesto del árbol y
debe ser perfectamente horizontal. Sitúese a la izquierda
del árbol y corte con cadena tirante.
Sitúe el corte de derribo a unos 3-5 cm (1,5-2 pulgadas)
por encima del plano horizontal del corte de indicación.
Hay técnicas para la tala de árboles con diámetros de
tronco más grandes que la longitud de la espada. Estas
técnicas conllevan un riesgo considerable de que el
sector de riesgo de reculada de la espada toque un
objeto.
El corte de derribo debe quedar paralelo con la línea de
corte de indicación, con una distancia mínima entre
ambos de 1/10 del diámetro del tronco. La parte del
tronco sin cortar se denomina faja de desgaje.
La faja de desgaje funciona como una bisagra que dirige
la dirección de derribo del árbol.
Se pierde completamente el control de la dirección de
derribo del árbol si la faja de desgaje es demasiado
72 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
tronco/la rama se suelte lo suficiente para que el tronco/
la rama se ”parta” en el punto de ruptura.
Tratamiento de una tala fallida
Derribo de un árbol ”atascado”
Es muy peligroso retirar un árbol atascado y hay un
elevado riesgo de accidente.
No intente nunca cortar árboles talados apoyados sobre
otros.
¡No corte nunca del todo un objeto en tensión!
Si necesita cortar a través del árbol/rama, haga dos o tres
cortes con una separación de 3 cm y una profundidad de
3 a 5 cm.
No trabaje nunca dentro de la zona de riesgo de árboles
talados atascados y suspendidos.
Continúe serrando a más profundidad hasta que soltar la
fuerza y la tensión del árbol/rama.
El método más seguro es utilizar un torno.
•
Montado en un tractor
Sierre el árbol/rama desde el lado opuesto después de
soltar la tensión.
Medidas preventivas de las
reculadas
•
Portátil
¡ATENCION! Las reculadas pueden ser
rapidísimas, repentinas y violentas,
!
lanzando la motosierra, la espada y la
cadena contra el usuario. Si la cadena en
movimiento toca al usuario, pueden
producirse lesiones muy graves e
incluso mortales. Es necesario
comprender las causas de las reculadas
y que pueden evitarse procediendo con
cuidado y trabajando con la técnica
correcta.
Corte de árboles y ramas tensos
Preparativos: Estime el sentido de la tensión y dónde
tiene su punto de ruptura (es decir, el punto en el que se
rompería si se siguiera tensando).
¿Qué es la reculada?
Reculada es la denominación de una reacción repentina
por la que la motosierra y la espada salen despedidas de
un objeto que ha entrado en contacto con el cuadrante
superior de la punta de la espada, denominado sector de
riesgo de reculada.
Determine la forma más segura de soltar la tensión y
también, si Ud. puede hacerlo. En situaciones muy
complicadas, el único método seguro consiste en utilizar
un torno en vez de la motosierra.
Generalidades:
Sitúese de modo que no haya riesgo de que sea
alcanzado por el tronco/la rama cuando se suelte.
La reculada sigue siempre el sentido del plano de la
espada. Lo más común es que la motosierra y la espada
reboten hacia atrás en sentido ascendente, hacia el
usuario. También hay otros sentidos de reculada
dependiendo de la posición de la motosierra en el
Haga uno o varios cortes en el punto de ruptura o cerca
del mismo. Corte a la profundidad requerida y con el
número de cortes necesarios para que la tensión del
115 13 80-96 Rev.3 2008-12-17
Spanish – 73
Download from Www.Somanuals.com. All Manuals Search And Download.
TECNICA DE TRABAJO
momento en que el sector de riesgo de reculada de la
Tronzado del tronco
espada toca un objeto.
Vea las instrucciones bajo el título Técnica básica de
corte.
La reculada sólo puede producirse cuando el sector de
riesgo de reculada de la espada toca un objeto.
Desramado
¡ATENCION! La mayoría de accidentes
por reculada ocurren al desramar. No
!
use el sector de riesgo de reculada de la
espada. Proceda con sumo cuidado y
evite que la punta de la espada entre
toque en el tronco, en otras ramas o en
objetos. Proceda con sumo cuidado con
las ramas que están tensadas. Pueden
ser despedidas contra usted y hacerle
perder el control, con el riesgo
consiguiente de daños.
¡Cerciórese de que pueda caminar y mantenerse de pie
con seguridad!Trabaje desde el lado izquierdo del tronco.
Trabaje lo más cerca posible de la motosierra para
máximo control. Cuando sea posible, descargue el peso
de la motosierra apoyándola en el tronco.
Desplácese solamente cuando el tronco esté situado
entre Ud. y la motosierra.
74 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
Generalidades
Control,mantenimiento y servicio
del equipo de seguridad de la
motosierra
El usuario sólo puede efectuar los trabajos de
mantenimiento y servicio descritos en este manual. Los
trabajos de mayor envergadura debe efectuarlos un taller
de servicio oficial.
Aclaración! Para todos los trabajos de servicio y
reparación de la máquina es necesaria una capacitación
especial. Esto es especialmente aplicable al equipo de
seguridad. Si la máquina no da resultados satisfactorios
en alguno de los controles de la lista abajo, le
Ajuste del carburador
Su producto Husqvarna ha sido construido y fabricado
conforme a especificaciones que reducen los gases de
escape tóxicos.
recomendamos que acuda a un taller de servicio.
Funcionamiento
Freno de cadena con protección contra
reculadas
•
El régimen del motor se controla mediante el
acelerador y el carburador. En el carburador se
efectúa la dosificación de la mezcla de aire y
combustible. Esta mezcla es regulable. Para obtener
la potencia máxima de la máquina, el reglaje de la
dosificación debe ser correcto.
Control del desgaste de la cinta de freno
•
Con el tornillo T se regula la posición del acelerador
en ralentí. El ralentí se aumenta girando el tornillo T
en el sentido de las agujas del reloj y se reduce
girándolo en sentido contrario a las agujas del reloj.
Limpie el freno de cadena y el tambor de embrague de
serrín, resina y suciedad. La suciedad y el desgaste
perjudican la función de frenado.
Reglaje básico y rodaje
El reglaje básico del carburador se lleva a cabo en las
pruebas que se hacen en fábrica. El ajuste fino debe
efectuarlo un técnico capacitado.
Régimen recomendado en ralentí: Vea el capítulo Datos
técnicos.
Reglaje preciso del ralentí, tornillo T
El ralentí se regula con el tornillo marcado con unaT.Para
regular, enrosque (en el sentido de las agujas del reloj) el
tornillo T con el motor en marcha hasta que empiece a
girar la cadena. A continuación, desenrosque (en sentido
contrario a las agujas del reloj) hasta que la cadena se
pare. El reglaje del régimen de ralentí es correcto cuando
el motor funciona regularmente en todas las posiciones,
habiendo un buen margen hasta el régimen en que
empieza a girar la cadena.
Controle regularmente que el punto más desgastado de
la cinta de freno tenga un mínimo de 0,024” (0,6 mm) de
grosor.
Control de la protección contra reculadas
Compruebe que la protección contra reculadas esté
intacta, sin defectos visibles como, por ejemplo, grietas.
¡ATENCION! Si el régimen de ralentí no
puede ajustarse para que se pare la
!
cadena, acuda a un taller de servicio. No
utilice la motosierra hasta que esté
correctamente regulada o reparada.
Carburador correctamente regulado
Empuje la protección contra reculadas adelante y atrás
para comprobar que se mueve con facilidad y que está
firmemente anclada a su articulación en la cubierta del
embrague.
Con el carburador correctamente regulado, la máquina
acelera sin dilación y ”ronronea” ligeramente a plena
aceleración. Además, la cadena no debe girar en ralentí.
El reglaje demasiado pobre del surtidor L puede
ocasionar dificultades de arranque y mala aceleración. El
reglaje demasiado pobre del surtidor H reduce la
potencia de la máquina y ocasiona mala aceleración y/o
la avería del motor.
115 13 80-96 Rev.3 2008-12-17
Spanish – 75
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
Control de la función de inercia
Acelere al máximo y active el freno de cadena girando la
muñeca izquierda hacia la protección contra reculadas.
No suelte el mango delantero. La cadena debe
detenerse inmediatamente.
Mantenga la motosierra, con el motor parado, sobre un
tocón u otro objeto estable. Suelte la empuñadura
delantera y deje caer la motosierra por su propio peso,
rotando en la empuñadura trasera, contra el tocón.
Fiador del acelerador
•
Compruebe que el acelerador esté bloqueado en la
posición de ralentí cuando el fiador está en su
posición inicial.
El freno de cadena debe activarse cuando la punta de
la espada toca el tocón.
•
Apriete el fiador del acelerador y compruebe que
vuelva a su posición de partida al soltarlo.
Control del efecto de frenado
Coloque la motosierra sobre una base firme y arránquela.
Fíjese que la cadena no entre en contacto con el suelo u
otro objeto. Consulte las instrucciones bajo el título
Arranque y parada.
•
•
Compruebe que el acelerador y el fiador se muevan
con facilidad y que funcionen sus muelles de retorno.
Arranque la motosierra y acelere al máximo. Suelte el
acelerador y compruebe que la cadena se pare y
permanezca inmóvil. Si la cadena gira con el
acelerador en la posición de ralentí debe controlarse
el reglaje de ralentí del carburador.
Sostenga la motosierra con firmeza, agarrando los
mangos con todos los dedos.
76 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
Captor de cadena
Botón de parada
Compruebe que el captor de cadena esté intacto y que
esté firmemente montado al cuerpo de la motosierra.
Arranque el motor y compruebe que se pare cuando se
mueve el botón de parada a la posición de parada.
¡NOTA! El contacto de arranque/parada retorna
automáticamente a la posición de marcha. Por
Protección de la mano derecha
consiguiente, para evitar el arranque involuntario hay que
quitar siempre el capuchón de encendido de la bujía antes
de realizar trabajos de montaje, control y/o mantenimiento.
Silenciador
Compruebe que la protección de la mano derecha esté
intacta, sin defectos visibles como, por ejemplo, grietas.
Nunca utilice una máquina que tenga un silenciador
defectuoso.
Sistema amortiguador de vibraciones
Compruebe regularmente que el silenciador esté
firmemente montado en la máquina.
Compruebe regularmente que los elementos
antivibraciones no estén agrietados o deformados.
Compruebe que los elementos antivibraciones estén bien
anclados entre la parte del motor y la parte de los
mangos, respectivamente.
Algunos silenciadores incorporan una rejilla
apagachispas. Si el silenciador de su máquina lleva rejilla
apagachispas, límpiela cada semana. Lo mejor es utilizar
un cepillo de acero.Una red apagachispas obturada hace
que se sobrecaliente el motor, con el riesgo consiguiente
de avería grave del motor.
Aclaración! Si la rejilla tiene desperfectos, cámbiela. Con
una rejilla obturada, la máquina se sobrecalienta y se
averían el cilindro y el pistón. No utilice nunca la máquina
si el silenciador está en mal estado. Nunca utilice un
115 13 80-96 Rev.3 2008-12-17
Spanish – 77
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
silenciador sin una rejilla apagachispas o con una
rejilla apagachispas defectuosa.
•
Afloje el tornillo del centro de la polea y saque la
rueda de arrastre (A), el muelle de arrastre (B) y la
polea (C). Inserte y fije el cordón de arranque en la
polea. Enrolle unas 3 vueltas del cordón de arranque
en la polea.Monte la polea contra el muelle de retorno
(D), enganchando el extremo de éste en la polea. A
continuación monte el muelle de arrastre, la rueda de
arrastre y el tornillo en el centro de la polea. Inserte el
cordón de arranque en el agujero de la caja del
mecanismo de arranque y en la empuñadura de
arranque. A continuación haga un nudo resistente en
el cordón de arranque.
El silenciador está diseñado para amortiguar el ruido y
para apartar del usuario los gases de escape. Los gases
de escape están calientes y pueden contener chispas
que pueden ocasionar incendios si se dirigen los gases a
materiales secos e inflamables.
Mecanismo de arranque
¡ATENCION! El muelle de retorno está
tensado en el cuerpo del mecanismo de
!
arranque y, con una manipulación
negligente, puede soltarse y causar
lesiones.
Para cambiar el muelle de arranque o el
cordón de arranque, proceda con
cuidado. Utilice gafas protectoras y
guantes protectores.
Tensado del muelle de retorno
Cambio del cordón de arranque
•
Saque el cordón de arranque de la guía de la polea y gire
ésta en el sentido de las agujas del reloj unas 2 vueltas.
Aclaración! Compruebe que sea posible girar la polea
como mínimo 1/2 vuelta más con el cordón totalmente
extraído.
•
Afloje los tornillos que fijan el mecanismo de arranque
en el cárter y saque el mecanismo.
•
Extraiga el cordón unos 30 cm y sáquelo de la guía en
la periferia de la polea. Anule el efecto del muelle de
retorno dejando que la polea gire despacio hacia atrás.
Estire el cordón con la empuñadura. Aparte el pulgar y
suelte el cordón. Vea la figura abajo.
2
1
78 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
Cambio del muelle de retorno y el muelle
de arrastre
Filtro de aire
El filtro de aire debe limpiarse regularmente de polvo y
suciedad para evitar:
Muelle de retorno (A)
•
•
•
•
•
•
Fallos del carburador
•
Levante la polea. Vea las instrucciones bajo el título
Cambio de un cordón de arranque roto o desgastado.
Tenga en cuenta que el muelle de retorno está tenso
en el cuerpo del mecanismo de arranque.
Problemas de arranque
Reducción de la potencia
Desgaste innecesario de las piezas del motor
Un consumo de combustible excesivo
•
•
Desmonte el casete con el muelle de retorno fuera del
mecanismo de arranque.
Para desmontar el filtro, saque primero la cubierta del
cilindro. Al montar, compruebe que el filtro quede
colocado herméticamente contra el soporte. Para
limpiar el filtro, sacúdalo o cepíllelo.
Lubrique el muelle de retorno con aceite claro. Monte
el casete con el muelle de retorno en el mecanismo
de arranque. Monte la polea y tense el muelle de
retorno.
Muelle de arrastre (B)
•
Afloje el tornillo del centro de la polea y saque la
rueda de arrastre y el muelle de arrastre.
•
Cambie el muelle de arrastre y monte la rueda de
arrastre encima del muelle.
Para una limpieza a fondo del filtro, lávelo en agua
jabonosa.
A
B
Un filtro utilizado durante mucho tiempo no puede
limpiarse del todo. Por tanto, hay que cambiarlo a
intervalos regulares. Un filtro de aire averiado debe
cambiarse.
Una motosierra HUSQVARNA puede equiparse con
varios tipos de filtro de aire, según el medio de trabajo, el
clima, la estación del año, etc. Consulte a su distribuidor
para mayor información.
Montaje del mecanismo de arranque
•
Para montar el mecanismo de arranque, primero
extraiga el cordón y después coloque el mecanismo
en su sitio en el cárter. Luego, suelte despacio el
cordón para que los ganchos agarren la polea.
•
Ponga los tornillos de fijación del mecanismo de
arranque y apriételos.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 79
MANTENIMIENTO
Bujía
Lubricación del cojinete de
agujas
Los factores siguientes afectan al estado de la bujía:
El tambor de embrague tiene un cojinete de agujas en el
eje saliente. Este cojinete de agujas se debe lubricar
regularmente.
•
•
Carburador mal regulado.
Mezcla de aceite inadecuada en el combustible
(demasiado aceite o aceite inadecuado).
Para lubricar se desmonta el envolvente del embrague
aflojando las dos tuercas de la espada. A continuación
coloque la sierra con el tambor de embrague arriba.
•
Filtro de aire sucio.
Estos factores producen revestimientos en los electrodos
de la bujía que pueden ocasionar perturbaciones del
funcionamiento y dificultades de arranque.
La lubricación se hace goteando aceite de motor en el
centro del tambor de embrague al mismo tiempo que se
gira éste.
Si la potencia de la máquina es demasiado baja, si es
difícil arrancar la máquina o si el ralentí es irregular:
revise primero la bujía antes de tomar otras medidas. Si
la bujía está muy sucia, límpiela y compruebe que la
separación de los electrodos sea de 0,5 mm. La bujía
debe cambiarse aproximadamente después de un mes
de funcionamiento o más a menudo si es necesario.
Sistema refrigerante
Aclaración! ¡Utilice siempre el tipo de bujía recomendado!
Una bujía incorrecta puede arruinar el pistón y el cilindro.
Asegúrese de que la bujía tenga supresión de
perturbaciones radioeléctricas.
Para lograr una temperatura de funcionamiento lo más
baja posible, la máquina incorpora un sistema
refrigerante.
El sistema refrigerante está compuesto por:
1
2
3
4
5
Toma de aire en el mecanismo de arranque.
Deflector de aire.
Engrase del cabezal de rueda de
la espada
Palas de ventilador en el volante.
Aletas de enfriamiento en el cilindro.
Cubierta del cilindro (dirige el aire refrigerante hacia el
cilindro).
El cabezal de rueda de la espada debe engrasarse en
cada repostaje. Utilice la pistola de engrase especial y
grasa para cojinetes de buena calidad.
Limpie el sistema refrigerante con un cepillo una vez por
semana (en condiciones difíciles, con mayor frecuencia).
Un sistema refrigerante sucio u obturado produce
sobrecalentemiento de la máquina, con las consiguientes
averías del cilindro y el pistón.
80 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
MANTENIMIENTO
°
°
Temperaturas de -5 C (23 F) o inferiores:
Depuración centrífuga ”Air
Injection”
Con la depuración centrífuga, todo el aire que va al
carburador entra (es absorbido) a través del mecanismo
de arranque. El ventilador de enfriamiento evacúa
centrífugamente la suciedad y el polvo.
Para utilizar la máquina en climas fríos o con polvillo de
nieve, hay una cubierta especial que se coloca sobre el
cuerpo del mecanismo de arranque. Se reduce así la
entrada de aire frío y se impide la aspiración de grandes
cantidades de nieve.
¡IMPORTANTE! Para que la depuración centrífuga
funcione satisfactoriamente, debe efectuarse un
mantenimiento constante del sistema. Limpie la toma de
aire del mecanismo de arranque, las palas de ventilador
del volante, el espacio alrededor del volante, el tubo de
admisión y el compartimiento del carburador.
¡NOTA! Si se ha montado el conjunto especial de invierno
o si se han tomado medidas para aumentar la
temperatura, debe cambiarse al reglaje normal, puesto
que la máquina funciona con temperatura normal. De lo
contrario, hay riesgo de sobrecalentemiento con las
consiguientes averías graves del motor.
Utilización en invierno
Al usar la máquina en clima frío o con nieve pueden
producirse perturbaciones del funcionamiento, a causa
dev:
¡IMPORTANTE! Todas las medidas de mantenimiento
que no estén indicadas en este manual deben ser
efectuadas por una tienda autorizada con servicio
(distribuidor).
•
•
Temperatura muy baja del motor.
Formación de hielo en el filtro de aire y congelación
del carburador.
Por consiguente, suelen requerirse medidas especiales
como:
•
Reducción parcial de la toma de aire del mecanismo
de arranque, con el aumento consiguiente de la
temperatura del motor.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
Spanish – 81
MANTENIMIENTO
Programa de mantenimiento
A continuación incluimos una lista con los puntos de mantenimiento a efectuar en la máquina. La mayoría de los puntos
se describen en el capítulo “Mantenimiento”.
Mantenimiento diario
Mantenimiento semanal
Mantenimiento mensual
Compruebe si está desgastada la
cinta del freno de cadena. Cámbiela
cuando quede menos de 0,6 mm en
el punto más gastado.
En motosierras sin catalizador,
controle el sistema de refrigeracón
semanalmente.
Limpie la parte exterior de la
máquina.
Compruebe que los componentes del
acelerador funcionen con seguridad.
(Fiador y acelerador.)
Compruebe si están desgastados el
centro, el tambor y el muelle de
embrague.
Revise el mecanismo de arranque y el
resorte de retorno.
Limpie el freno de cadena y
compruebe que funcione con
seguridad. Verifique que el captor de
cadena esté intacto y cámbielo si es
necesario.
Limpie la bujía. Compruebe que la
separación de los electrodos sea de
0,5 mm.
Compruebe que los elementos
antivibración no están dañados.
La espada debe girarse regularmente
para que el desgaste sea igualado.
Compruebe que el orificio de
lubricación de la espada no esté
obturado.Limpie la guía de la cadena.
Si la espada tiene cabezal de rueda,
engráselo.
Engrase el cojinete del tambor del
embrague.
Limpie el exterior del carburador.
Revise el filtro y el conducto de
combustible. Cámbielos si es
necesario.
Compruebe que la espada y la
cadena reciban aceite suficiente.
Lime las eventuales rebabas en los
lados de la espada.
Revise la cadena de sierra en lo
referente a grietas en remaches y
eslabones, rigidez de la cadena o
desgaste anormal de remaches y
eslabones. Cambie las piezas
gastadas.
Limpie o cambie el apagachispas del Vacíe el depósito de combustible y
silenciador.
límpielo interiormente.
Afile la cadena y compruebe su
tensado y su estado. Verifique que el
píñón de arrastre de la cadena no
esté demasiado desgastado,
cámbielo si es necesario.
Limpie el compartimento del
carburador.
Vacíe el depósito de aceite y límpielo
interiormente.
Limpie la toma de aire del mecanismo Limpie el filtro de aire. Cámbielo si es
Revise todos los cables y conexiones.
de arranque.
necesario.
Compruebe que los tornillos y las
tuercas estén apretados.
Controle que el mando de detención
funcione.
Controle que no haya fugas de
combustible del motor, del depósito o
de los conductos de combustible.
En motosierras con catalizador,
controle el sistema de refrigeración
diariamente.
82 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
DATOS TECNICOS
Datos técnicos
435
435e
440e
Motor
Cilindrada, pulgadas/cm3
Diámetro del cilindro, pulgadas/mm
Carrera, pulgadas/mm
Régimen de ralentí, rpm
Potencia, kW/rpm
2,49/40,9
1,61/41
2,49/40,9
1,61/41
2,49/40,9
1,61/41
1,22/31
1,22/31
1,22/31
2900
2900
2900
1,6/2,2 @ 9000
1,6/2,2 @ 9000
1,8/2,4 @ 9000
Sistema de encendido
Fabricante de sisterna de encendido
Tipo de sisterna de encendido
Bujía
Walbro
Walbro
Walbro
MBU-33
MBU-33
MBU-33
NGK BPMR 7A/
NGK BPMR 7A/
NGK BPMR 7A/
Champion RCJ 7Y/ Champion RCJ 7Y/ Champion RCJ 7Y/
Husqvarna PR 17Y Husqvarna PR 17Y Husqvarna PR 17Y
Distancia de electrodos, pulgadas/mm
Sistema de combustible y lubricación
Fabricante de carburador
0,02/0,5
0,02/0,5
0,02/0,5
Zama
Zama
Zama
Tipo de carburador
EL 41
EL 41
EL 41
Capacidad del depósito de gasolina, US pint/litros
Caudal de la bomba de aceite a 9.000 rpm, ml/min.
Capacidad del depósito de aceite, US pint/litros
Tipo de bomba de aceite
0,78/0,37
13
0,78/0,37
13
0,78/0,37
13
0,53/0,25
No ajustable
0,53/0,25
No ajustable
0,53/0,25
No ajustable
Peso
Motosierra sin espada ni cadena, con depósitos vacíos, lb/kg 9,3/4,2
9,7/4,4
13"/33
9,7/4,4
13"/33
Cadena /espada
Longitud de espada estándar, pulgadas/cm
Longitudes de espada recomendadas, pulgadas/cm
Longitud efectiva de corte, pulgadas/cm
Paso, pulgadas/mm
13"/33
0,325/8,25
0,050/1,3
Spur/7
0,325/8,25
0,050/1,3
Spur/7
0,325/8,25
0,050/1,3
Spur/7
Grosor del eslabón de arrastre, pulgadas/mm
Tipo de piñón de arrastre/número de dientes
Velocidad de la cadena a potencia máxima, m/s
17,3
17,3
17,3
Spanish – 83
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
DATOS TECNICOS
Combinaciones aprobadas de espada y cadena originales y de repuesto
A continuación se presenta una lista de los equipos de corte recomendados para los modelos de motosierras Husqvarna
435, 435e y 440e. Las combinaciones de cabezal de fuerza, espada y cadena han sido probadas y se ha verificado que
cumplen con los requisitos de reculada y vibraciones de ANSI B175.1–2000.
El radio de la punta de la espada viene determinado bien por el número máximo de dientes del piñón de la punta o por
el radio de punta máximo correspondiente de una espada sólida.
La lista siguiente contiene las recomendaciones del fabricante de la motosierra. Puede haber disponibles otras
combinaciones que también consiguen la reducción de la reculada.
En la lista se indica el radio de punta de espada máximo, por lo que también es posible usar una espada con radio de
punta más pequeño que el indicado en la lista. Para espadas de la misma longitud, todas las espadas con punta de
piñón tienen el mismo paso y, al tener el mismo número de dientes de piñón, puede considerarse que tienen una energía
de reculada equivalente. Puede considerarse que una espada de punta dura de la misma longitud y radio de punta que
una espada con punta de piñón tiene una energía de reculada equivalente o menor que la espada con punta de piñón.
Combinaciones de espada y cadena
Los modelos de motosierra 435, 435e y 440e de Husqvarna cumplen los requisitos de rendimiento en reculada de ANSI
B 175.1-2000 en ensayos con las combinaciones de espadas y cadenas indicadas a continuación. La cadena de
motosierra H30 de Husqvarna también está clasificada como cadena de motosierra de reculada reducida, porque
cumple los requisitos de cadena de motosierra de reculada reducida definidos en ANSI B 175.1-2000. Recomendamos
usar solamente las combinaciones indicadas de espadas y cadenas para los modelos de motosierra 435, 435e y 440e
de Husqvarna. Otros modelos de motosierras podrían no cumplir los requisitos de reculada, si se equipan con las
combinaciones de espada y cadena indicadas.
Espada
Cadena
Longitud, Paso,
pulgadas
Anchura de Máximo número de dientes,
Longitud, eslabones
de arrastre (unidad)
Tipo
pulgadas ranura, mm
cabezal de rueda
13
15
16
18
0,325
0,325
0,325
0,325
10T
10T
10T
10T
56
64
66
72
1,3
Husqvarna H30
Afilado y calibres de afilado de la cadena de sierra
84 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES FEDERAL Y CALIFORNIANA
FECHA DE INICIO DE LA GARANTIA
SUS DERECHOS Y
OBLIGACIONES DE GARANTIA
El período de garantía empieza en la fecha en la que el
motor o el equipo se entregan al comprador final.
La Agencia de protección medioambiental estadounidense
(EPA), el Consejo de recursos del aire de California
DURACION DE LA GARANTIA
(CARB), el Ministerio de Medioambiente de Canadá y
Husqvarna Forest & Garden garantiza al comprador final
Husqvarna Forest & Garden presentan la garantía del
y a cada propietario posterior que el motor o el equipo
sistema de control de emisiones de su motor todoterreno
está diseñado, fabricado y equipado de conformidad con
las regulaciones aplicables adoptadas por la EPA y el
CARB, y que no tiene defectos de fabricación ni en los
materiales que puedan causar el mal funcionamiento de
las piezas, cuya garantía es de dos años.
de tamaño pequeño, modelo de 2009 o posterior. En
Estados Unidos y Canadá es necesario diseñar, fabricar y
proporcionar nuevos equipos que utilicen motores
todoterreno de tamaño pequeño que cumplan con las
estrictas regulaciones antihumo federales y californianas.
Husqvarna Forest & Garden deberá garantizar el sistema
de control de emisiones de su motor todoterreno de
tamaño pequeño para el período especificado a
ALCANCE DE LA GARANTIA
REPARACION O SUSTITUCION DE COMPONENTES
La reparación o sustitución de cualquier pieza con
garantía se llevará a cabo sin coste alguno para el
propietario en un centro de garantía. Husqvarna Forest &
Garden proporcionará servicios de garantía o de
reparación en todos los centros de distribución
autorizados para reparar los motores en cuestión.
Durante el período de dos años de garantía de control de
emisiones, Husqvarna Forest & Garden debe tener en
stock las piezas en garantía suficientes para dar
respuesta a su demanda.
continuación, siempre que su equipo no haya sido tratado
indebidamente ni haya recibido un mantenimiento
inadecuado. Su sistema de control de emisiones puede
incluir piezas como el carburador, el sistema de ignición, el
catalizador, el depósito de combustible, los filtros y otros
componentes asociados. Además, pueden estar incluidos
las mangueras, las correas, los conectores, los sensores y
otros elementos relacionados con la emisión de humos.
Husqvarna Forest & Garden reparará su motor todoterreno
de tamaño pequeño sin ningún coste para usted, incluidos
el diagnóstico, las piezas y la mano de obra, siempre que
se cumpla alguna de las condiciones para la garantía.
PERIODO DE GARANTIA Cualquier pieza en garantía
que deba cambiarse según el programa de
ALCANCE DE LA GARANTIA DEL
FABRICANTE
El sistema de control de emisiones está garantizado durante
un período de dos años. Si cualquier pieza de su equipo
relacionada con la emisión de humos está defectuosa,
Husqvarna Forest & Garden la reparará o la sustituirá.
mantenimiento estará garantizada para el período de
tiempo previo al primer cambio programado. Si la pieza
falla antes del primer cambio programado, Husqvarna
Forest & Garden la reparará o la sustituirá sin ningún
coste. Cualquier pieza que se repare o cambie en el
periodo de garantía seguirá cubierta por la garantía
durante el periodo de tiempo restante hasta el primer
cambio programado. Cualquier pieza garantizada que no
requiera ningún cambio según el programa de
RESPONSABILIDADES DE GARANTIA
DEL PROPIETARIO
mantenimiento tiene una garantía de dos años. Si
cualquiera de estas piezas falla durante el periodo de
garantía, Husqvarna Forest & Garden la reparará o la
sustituirá sin ningún coste. ❍ Cualquier pieza reparada o
sustituida durante el periodo de garantía seguirá cubierta
por esta hasta que finalice el periodo total. Cualquier
pieza que solamente tenga programadas inspecciones
regulares según el programa de mantenimiento tendrá
una garantía de dos años. Una declaración contenida en
las instrucciones según la cual la pieza se deba «reparar
o cambiar cuando sea necesario» no reducirá el período
de garantía. Cualquier pieza que se repare o cambie en
el periodo de garantía seguirá cubierta por la garantía
durante el periodo de tiempo restante.
•
Como propietario de un motor todoterreno de tamaño
pequeño, usted es responsable de llevar a cabo el
mantenimiento correspondiente que figura en el manual
de instrucciones. Husqvarna Forest & Garden le
recomienda que guarde todos los recibos relacionados
con el mantenimiento de su motor todoterreno de
tamaño pequeño, si bien no podrá negarle su derecho a
la garantía por el mero hecho de no tenerlos o de no
haber realizado el mantenimiento estipulado.
•
•
Sin embargo, como propietario de un motor todoterreno
de tamaño pequeño, debe saber que Husqvarna Forest
& Garden puede negarle la cobertura de la garantía si
el motor o alguna de sus piezas falla debido a un mal
uso o a modificaciones no reglamentarias.
DIAGNOSTICO El propietario no deberá pagar por el
diagnóstico necesario para determinar si la pieza está
defectuosa si dicho trabajo de diagnóstico se realiza en el
centro de garantía.
Es responsabilidad suya llevar su motor todoterreno
de tamaño pequeño a un centro de distribución o de
reparación de Husqvarna Forest & Garden tan pronto
como aparezca un problema. Las reparaciones de la
garantía deben finalizarse en un plazo de tiempo
razonable que en ningún caso excederá los 30 días.
Si tiene cualquier pregunta relacionada con la
cobertura de la garantía, póngase en contacto con
Husqvarna Forest & Garden en el teléfono 1-800-487-
DANOSY PERJUICIOS Husqvarna Forest & Garden es
responsable de los daños y perjuicios en otros
componentes del motor causados directamente por el
fallo de una pieza en garantía.
Spanish – 85
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
DECLARACIÓN DE GARANTÍA DE CONTROL DE EMISIONES FEDERAL Y CALIFORNIANA
LISTA DE PIEZAS DE LA GARANTÍA DE
EMISIONES
1
2
Carburador y piezas interiores
Tubo de admisión, cuerpo del filtro de aire y tornillos
del carburador
3
Filtro de aire y filtro de combustible abarcados hasta
el plan de mantenimiento
4
5
6
7
Bujía, abarcada hasta el plan de mantenimiento
Módulo de encendido
Silenciador con catalizador
Depósito de combustible
LO QUE NO ABARCA LA GARANTIA
No se abarcan todos los fallos causados por abuso,
negligencia o mantenimiento indebido.
PIEZAS AÑADIDAS O MODIFICADAS
No podrán utilizarse piezas añadidas o modificadas que
no estén eximidas por el CARB o la EPA. La utilización de
cualquier pieza añadida o modificada que no esté
eximida será motivo suficiente para no atender una
solicitud de garantía. Husqvarna Forest & Garden no se
hará responsable de los fallos de piezas en garantía
causados por la utilización de piezas añadidas o
modificadas que no estén eximidas.
COMO HACER UNA RECLAMACION
Si tiene alguna duda en cuanto a sus derechos y
responsabilidades de garantía, póngase en contacto con
el servicio oficial más cercano, o llame a Husqvarna
Forest & Garden, teléfono 1-800-487-5951 o visite
DONDE RECIBIR SERVICIO DE
GARANTIA
Todos los distribuidores de servicios de reparación
autorizados de Husqvarna Forest & Garden proporcionan
servicios de garantía o de reparación.
MANTENIMIENTO, SUSTITUCIONY
REPARACION DE COMPONENTES
RELACIONADOS CON EMISIONES
Podrá utilizarse cualquier recambio en el mantenimiento
o la reparación durante el periodo de garantía sin coste
alguno para el propietario. Dicha utilización no reduce las
obligaciones de garantía del fabricante.
DECLARACION DE MANTENIMIENTO
El propietario es responsable de la realización de todo el
mantenimiento necesario, según se define en el manual
del operador.
86 – Spanish
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
PRECAUCIONES DE SEGURIDAD DE LA NORMA AMERICANA
Otras precauciones de seguridad
Precauciones de seguridad para
usuarios de motosierras
(ANSI B175.1-2000 Anexo C)
¡ATENCION! No maneje la motosierra
con una mano. El manejo con una sola
mano comporta riesgo de daños graves
al operador, los ayudantes, espectadores
!
Precauciones de seguridad en reculadas
o a una combinación de estas personas.
Las motosierras están concebidas para
ATENCIÓN! La reculada se puede
usar con dos manos.
producir cuando la punta de la espada
!
toca en un objeto o cuando la madera se
No utilice una motosierra si está fatigado.
cierra y agarra la cadena de la motosierra
Use calzado, ropas ceñidas, guantes protectores y
en el corte.
protecciones de ojos, auriculares y de cabeza.
En algunos casos el contacto de la punta
de la espada puede causar una reacción
de inversión rapidísima que hace rebotar
la espada hacia arriba y atrás hacia el
operador.
Proceda con cuidado al manipular combustible. Aparte la
motosierra a como mínimo 3 metros del lugar de
repostaje antes de poner en marcha el motor.
No permita la presencia de otras personas cerca de la
motosierra al ponerla en marcha o al cortar. Mantenga a
los espectadores y animales fuera de la zona de trabajo.
El agarre de la cadena de la motosierra a
lo largo de la parte superior de la espada
puede empujar la espada rápidamente
hacia atrás, contra el operador.
No empiece a cortar sin tener la zona de trabajo esté
despejada, los pies firmemente en el suelo y una ruta de
retirada del árbol abatido.
Mantenga todas las partes de su cuerpo apartadas de
cadena de la motosierra cuando funciona el motor.
Cualquiera de estas reacciones puede
hacerle perder el control de la
motosierra, con el riesgo consiguiente
de daños personales graves.
Antes de poner en marcha el motor, compruebe que la
cadena de la motosierra no toca en nada.
Transporte la motosierra con el motor parado, la espada
y la cadena en la parte trasera y el silenciador apartado
de su cuerpo.
No confíe exclusivamente en los
dispositivos de seguridad de su
motosierra. Usted, como usuario de
motosierra, debe tomar varias medidas
para que sus trabajos de corte no
comporten riesgo de accidentes y daños
personales.
No utilice una motosierra que esté dañada, incorrectamente
ajustada o que no esté armada completamente y de forma
segura. Compruebe que la cadena de la motosierra deja de
moverse cuando se suelta el acelerador.
Pare el motor antes de colocar la motosierra en el suelo.
Proceda con suma precaución al cortar arbustos y arbolitos
pequeños porque podría agarrarse material fino en la cadena
y ser lanzado contra usted o hacerle perder el equilibrio.
Con una comprensión básica del efecto de reculada,
usted puede reducir o eliminar el factor sorpresa. La
sorpresa súbita contribuye a los accidentes.
Cuando corte una rama tensada, preste atención al
retorno para que no le golpee cuando se suelta la tensión
en las fibras de madera.
Agarre firmemente la motosierra con ambas manos, con
la mano derecha en la empuñadura trasera y la mano
izquierda en la empuñadura delantera, cuando el motor
está en marcha. Agarre fuerte con los pulgares y dedos
envolviendo las empuñaduras de la motosierra. Un
agarre firme le ayudará a reducir la reculada y mantener
el control de la motosierra. No suelte las empuñaduras.
Mantenga las empuñaduras secas, limpias y libres de
aceite o mezcla de combustible.
Utilice la motosierra solamente en áreas bien ventiladas.
No utilice una motosierra en un árbol si no ha sido
especialmente formado para ello.
Asegúrese de que no hay obstáculos en la zona en que
está cortando. No permita que la punta de la espada
entre en contacto con troncos, ramas ni ningún otro
obstáculo que pudiera tocarse cuando se utiliza la
motosierra.
No utilice una motosierra por encima de la altura del hombro.
Todos los trabajos de servicio de una motosierra, excepto
los que se indican en las instrucciones de seguridad y
mantenimiento del manual del operador/propietario, deben
ser realizados por técnicos de servicio de motosierras
competentes. (Por ejemplo, si se utilizan herramientas
inadecuadas para desmontar el volante o si se usa una
herramienta inadecuada para sujetar el volante cuando se
desmonta el embrague, pueden producirse daños
Corte con velocidades altas del motor.
No extienda demasiado ni corte por encima de la altura
del hombro.
Siga las instrucciones de afilado y mantenimiento del
fabricante de la cadena.
estructurales en el volante que causen la rotura del mismo.)
Para transportar la motosierra, utilice la protección de
espada adecuada.
Utilice solamente las espadas y cadenas de repuesto
especificadas por el fabricante o equivalentes.
Aclaración: Este anexo está destinado principalmente al
consumidor o usuario ocasional.
115 13 80-96 Rev.3 2008-12-17
Spanish – 87
Download from Www.Somanuals.com. All Manuals Search And Download.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
´®z+SF)¶6¢¨
´®z+SF)¶6¢¨
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
1151380-96
´®z+SF)¶6¢¨
´®z+SF)¶6¢¨
2008-12-17
115 13 80-96 Rev.3 2008-12-17
Download from Www.Somanuals.com. All Manuals Search And Download.
|