Operator′s manual
T536 LiXP
Please read the operator’s manual carefully and make sure you understand the instructions before using the machine.
English
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY TO SYMBOLS
Environmental marking. Symbols on the
Symbols on the machine:
Translation of the original Swedish operating instruction.
product or its packaging indicate that this
product cannot be handled as domestic
waste. It must instead be submitted to an
appropriate recycling station for the
recovery of electrical and electronic
equipment.
WARNING! Chain saws can be
dangerous! Careless or incorrect use can
result in serious or fatal injury to the
operator or others.
Please read the operator’s manual
carefully and make sure you understand
the instructions before using the machine.
Direct current
Do not expose to rain.
Always wear:
•
•
•
Approved protective helmet
Approved hearing protection
Protective goggles or a visor
Other symbols/decals on the machine refer to special
certification requirements for certain markets.
Symbols on the battery and/or on
the battery charger:
This product is in accordance with
applicable EC directives.
This product must be
deposited at an
appropriate recycling
facility.
Noise emission to the environment
according to the European Community’s
Directive. The machine’s emission is
specified in the Technical data chapter
and on the label.
Li-ion
Fail-safe transformer
Use appropriate protections for foot-leg
and hand-arm.
WARNING! Kickback may occur when
the nose or tip of the guide bar touches
an object, and cause a lightning fast
reverse reaction, kicking the guide bar up
and towards the operator. May cause
serious personal injury.
Use and store battery charger only
indoors.
Double insulation
This saw should only be used by
persons who are specially trained
in tree maintenance work. See
operator’s manual!
Direction of rotation of the saw
chain and maximum length of
the guide bar.
L-Max
356 mm / 14"
Chain brake, activated (right)
Chain brake, not activated (left)
Chain oil fill.
2 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
KEY TO SYMBOLS
You will find the following decals on your machine, battery
and battery charger.
Symbols in the operator’s
manual:
Deactivate the machine by pressing
the start/stop button on the keypad.
CAUTION! In order to prevent
unintentional starting, the battery
must be removed from the machine
when assembling, checking and/or
performing maintenance.
Always remove the battery from the
machine when assembling, checking
and/or performing maintenace.
Li-ion
Always wear approved protective
gloves.
Regular cleaning is required.
Visual check.
The chain brake must be engaged
when the chain saw is started.
WARNING! Kickback may occur when
the nose or tip of the guide bar touches
an object, and cause a lightning fast
reverse reaction, kicking the guide bar
up and towards the operator. May cause
serious personal injury.
English – 3
Download from Www.Somanuals.com. All Manuals Search And Download.
CONTENTS
Contents
KEY TO SYMBOLS
Symbols on the battery and/or on the battery
CONTENTS
INTRODUCTION
WHAT IS WHAT?
What is what on the chain saw? ........................... 6
GENERAL SAFETY PRECAUTIONS
Important .............................................................. 9
ASSEMBLY
BATTERY HANDLING
Disposal of the battery, battery charger and
STARTING AND STOPPING
WORKING TECHNIQUES
MAINTENANCE
Checking, maintaining and servicing chain saw
TECHNICAL DATA
4 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
INTRODUCTION
Dear Customer,
Congratulations on your choice to buy a Husqvarna product! Husqvarna is based on a tradition that dates back to 1689,
when the Swedish King Karl XI ordered the construction of a factory on the banks of the Husqvarna River, for production
of muskets. The location was logical, since water power was harnessed from the Huskvarna River to create the water-
powered plant. During the more than 300 years in existence, the Husqvarna factory has produced a lot of different
products, from wood stoves to modern kitchen appliances, sewing machines, bicycles, motorcycles etc. In 1956, the first
motor driven lawn mowers appeared, followed by chain saws in 1959, and it is within this area Husqvarna is working
today.
Today Husqvarna is one of the leading manufacturers in the world of forest and garden products, with quality as our
highest priority. The business concept is to develop, manufacture and market motor-driven products for forestry and
gardening, as well as for the building and construction industry. Husqvarna′s aim is also to be at the front edge for
ergonomics, usability, security and environmental protection. That is the reason why we have developed many different
features to add to our products within these areas.
We are convinced that you will appreciate with great satisfaction the quality and performance of our product for a very
long time to come. The purchase of one of our products gives you access to professional help with repairs and service
whenever this may be necessary. If the retailer who sells your machine is not one of our authorised dealers, ask for the
address of your nearest service workshop.
It is our wish that you will be satisfied with your product and that it will be your companion for a long time. Think of this
operator′s manual as a valuable document. By following its content (usage, service, maintenance, etc), the life span and
the second-hand value of the machine can be extended. If you sell this machine, make sure that the operator′s manual
is passed on to the buyer.
Thank you for using a Husqvarna product.
Husqvarna AB has a policy of continuous product development and therefore reserves the right to modify the design and
appearance of products without prior notice.
English – 5
Download from Www.Somanuals.com. All Manuals Search And Download.
WHAT IS WHAT?
13
14
3
4
5
1
2
15
6
7
21 20
19
18
17
16
12
11
22
10
23
24
9
8
25
28
29
30
27
32
31
33
26
What is what on the chain saw?
1
2
3
4
5
6
7
8
9
Front hand guard
Keypad
18 Guide bar
19 Chain catcher
SavE button
20 Chain tensioning screw
21 Drive sprocket cover
22 Guide bar cover
23 Charging LED
Warning indicator
Activate and deactivate button
Information and warning decal
Top handle
24 Warning indicator
25 Power cord
Belt eyelet
Rope eyelet
26 Battery charger
27 Combination spanner
28 Button, battery status
29 Battery status
10 Fan housing
11 Chain oil tank
12 Front handle
13 Power trigger lockout
14 Power trigger
15 Spike bumper
16 Bar tip sprocket
17 Saw chain
30 Warning indicator
31 Battery release buttons
32 Battery
33 Operator′s manual
6 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
moment of inattention while operating power tools
may result in serious personal injury.
General power tool safety
warnings
•
Use personal protective equipment. Always wear
eye protection. Protective equipment such as dust
mask, non-skid safety shoes, hard hat, or hearing
protection used for appropriate conditions will reduce
personal injuries.
WARNING! Read all safety warnings and
all instructions. Failure to follow the
warnings and instructions may result in
electric shock, fire and/or serious injury.
!
•
Prevent unintentional starting. Ensure the switch
is in the OFF-position before connecting to power
source and/or battery pack, picking up or carrying
the tool. Carrying power tools with your finger on the
switch or energising power tools that have the switch
on invites accidents.
IMPORTANT! Save all warnings and instructions for
future reference. The term ”power tool” in the warnings
refers to your mains-operated (corded) power tool or
battery-operated (cordless) power tool.
•
Remove any adjusting key or wrench before
turning the power tool on. A wrench or a key left
attached to a rotating part of the power tool may result
in personal injury.
Work area safety
•
Keep work area clean and well lit. Cluttered or dark
areas invite accidents.
•
•
Do not overreach. Keep proper footing and
balance at all times. This enables better control of
the power tool in unexpected situations.
•
Do not operate power tools in explosive
atmospheres, such as in the presence of
flammable liquids, gases or dust. Power tools
create sparks which may ignite the dust or fumes.
Dress properly. Do not wear loose clothing or
jewellery. Keep your hair, clothing and gloves
away from moving parts. Loose clothes, jewellery or
long hair can be caught in moving parts.
•
Keep children and bystanders away while
operating a power tool. Distractions can cause you
to lose control.
•
•
If devices are provided for the connection of dust
extraction and collection facilities, ensure these
are connected and properly used. Use of dust
collection can reduce dust-related hazards.
Electrical safety
•
•
Power tool plugs must match the outlet. Never
modify the plug in any way. Do not use any
adapter plugs with earthed (grounded) power
tools. Unmodified plugs and matching outlets will
reduce the risk of electric shock.
The vibration emission during actual use of the power
tool can differ from the declared total value depending
on the ways in which the tool is used. Operators
should identify safety measures to protect themselves
that are based on an estimation of exposure in the
actual conditions of use (taking account of all parts of
the operating cycle such as the times when the tool is
switched off and when it is running idle in addition to
the trigger).
Avoid body contact with earthed or grounded
surfaces, such as pipes, radiators, ranges and
refrigerators. There is an increased risk of electric
shock if your body is earthed or grounded.
•
•
Do not expose power tools to rain or wet
conditions. Water entering a power tool will increase
the risk of electric shock.
Power tool use and care
•
•
•
Do not force the power tool. Use the correct power
tool for your application. The correct power tool will
do the job better and safer at the rate for which it was
designed.
Do not abuse the cord. Never use the cord for
carrying, pulling or unplugging the power tool.
Keep cord away from heat, oil, sharp edges or
moving parts. Damaged or entangled cords increase
the risk of electric shock.
Do not use the power tool if the switch does not
turn it on and off. Any power tool that cannot be
controlled with the switch is dangerous and must be
repaired.
•
•
When operating a power tool outdoors, use an
extension cord suitable for outdoor use. Use of a
cord suitable for outdoor use reduces the risk of
electric shock.
Disconnect the plug from the power source and/or
the battery pack from the power tool before
making any adjustments, changing accessories,
or storing power tools. Such preventive safety
measures reduce the risk of starting the power tool
accidentally.
If operating a power tool in a damp location is
unaviodable, use a residual current device (RCD)
protected supply. Use of an RCD reduces the risk of
electric shock.
Personal safety
•
Store idle power tools out of the reach of children
and do not allow persons unfamiliar with the
power tool or these instructions to operate the
power tool. Power tools are dangerous in the hands
of untrained users.
•
Stay alert, watch what you are doing and use
common sense when operating a power tool. Do
not use a power tool while you are tired or under
the influence of drugs, alcohol or medication. A
English – 7
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
Maintain power tools. Check for misalignment or
wire may make exposed metal parts of the power tool
” live” and could give the operator an electric shock.
binding of moving parts, breakage of parts and
any other condition that may affect the power
tool´s operation. If damaged, have the power tool
repaired before use. Many accidents are caused by
poorly maintained power tools.
•
Wear safety glasses and hearing protection.
Further protective equipment for head, hands,
legs and feet is recommended. Adequate protective
clothing will reduce personal injury by flying debris or
accidental contact with the saw chain.
•
•
Keep cutting tools sharp and clean. Properly
maintained cutting tools with sharp cutting edges are
less likely to bind and are easier to control.
•
Always keep proper footing and operate the chain
saw only when standing on fixed, secure and level
surface. Slippery or unstable surfaces such as
ladders may cause a loss of balance or control of the
chain saw.
Use the power tool, accessories and tool bits etc.
in accordance with these instructions, taking into
account the working conditions and the work to
be performed. Use of the power tool for operations
different from those intended could result in a
hazardous situation.
•
•
•
When cutting a limb that is under tension be alert
for spring back. When the tension in the wood fibres
is released the spring loaded limb may strike the
operator and/or throw the chain saw out of control.
Battery tool use and care
Use extreme caution when cutting brush and
saplings. The slender material may catch the saw
chain and be whipped forward toward you or pull you
off balance.
•
Recharge only with the charger specified by the
manufacturer. A charger that is suitable for one type
of battery pack may create a risk of fire when used
with another battery pack.
Carry the chain saw by the handle with the chain
saw switched off and away from your body.When
transporting or storing the chain saw always fit
the guide bar cover. Proper handling of the chain
saw will reduce the likelihood of accidental contact
with the moving saw chain.
•
•
Use power tools only with specifically designated
battery packs. Use of any other battery packs may
create a risk of injury and fire.
When a battery pack is not in use, keep it away
from other metal objects, like paper clips, coins,
keys, nails, screws or other small metal objects,
that can make a connection from one terminal to
another. Shorting the battery terminals together may
cause burns or a fire.
•
Follow the instruction for lubricating, chain
tensioning and changing accessories. Improperly
tensioned or lubricated saw chain may either brake or
increase the chance of kickback.
•
Under abusive conditions, liquid may be ejected
from the battery; avoid contact. If contact
accidentally occurs, flush with water. If liquid
contacts eyes, additionally seek medical help.
Liquid ejected from the battery may cause irritations
or burns.
•
•
Keep handles dry, clean and free from oil and
grease. Greasy, oily handles are slippery causing
loss of control.
Cut wood only. Do not use chain saw for purposes
not intended. For example: do not use chain saw
for cutting plastic, masonry or nonwood building
materials. Use of the chain saw for operations
different than intendedcould result in a hazardous
situation.
Service
•
Have your power tool serviced by a qualified
repair person using only identical replacement
parts.This will ensure that the safety of the power tool
is maintained.
Causes and operator prevention of
kickback
Chain saw safety warnings
Kickback may occur when the nose or tip of the guide bar
touches an object, or when the wood closes in and
pinches the saw chain in the cut. Tip contact in some
cases may cause a sudden reverse reaction, kicking the
guide bar up and back towards the operator. Pinching the
saw chain along the top of the guide bar may push the
guide bar rapidly back towards the operator. Either of
these reactions may cause you to lose control of the saw
which could result in serious personal injury. Do not rely
exclusively upon the safety devises built into your saw. As
a chain saw user, you should take several steps to keep
your cutting jobs free from accident or injury. Kickback is
a result of tool misuse and/or incorrect operating
procedures or conditions and can be avoided by taking
proper precautions as given below:
•
Keep all parts of the body away from the saw chain
when the chain saw is operating. Before you start
the chain saw, make sure the saw chain is not
contacting anything. A moment of inattention while
operating chain saws may cause entanglement of you
clothing or body with the saw chain.
•
•
Always hold the chain saw with your right hand on
the rear handle and your left hand on the front
handle. Holding the chain saw with a reversed hand
configuration increases the risk of personal injury and
should never be done.
Hold the power tool by insulated gripping surface
only, because the saw chain may contact hidden
wiring or its own cord. Saw chain contacting a ”live”
8 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
•
Maintain a firm grip, with thumbs and fingers
WARNING! This machine produces an
electromagnetic field during operation.
This field may under some
circumstances interfere with active or
passive medical implants.To reduce the
risk of serious or fatal injury, we
recommend persons with medical
implants to consult their physician and
the medical implant manufacturer before
operating this machine.
encircling the chain saw handles, with both hands
on the saw and position your body and arm to
allow you to resist kickback forces. Kickback forces
can be controlled by the operator, if proper
!
precautions are taken. Do not let go of the chain saw.
Do not overreach and do not cut above shoulder
height. This helps prevent unintended tip contact and
enables better control of the chain saw in unexpected
situations.
•
•
Only use replacement bars and chains specified
by the manufacturer. Incorrect replacement bars and
chains may cause chain breakage and/or kickback.
Important
IMPORTANT!
Follow the manufacturer’s sharpening and
maintenance instructions for the saw chain.
Decreasing the depth gauge height can lead to
increased kickback.
This chain saw for tree service is designed for pruning
and dismantling standing tree crowns.
You should only use the saw with the bar and chain
combinations we recommend in the chapter Technical
data.
Before using a new chain saw
Never use the machine if you are fatigued, while under
the influence of alcohol or drugs, medication or anything
that could affect your vision, alertness, coordination or
judgement.
•
Please read this manual carefully.
•
Fully charge the battery before using it the first time.
See instructions under the heading Charging the
battery.
Wear personal protective equipment. See instructions
under the ”Personal protective equipment” heading.
•
•
Fill with chain oil. See instructions under the heading
Filling with chain oil.
Do not modify this product or use it if it appears to have
been modified by others.
Do not use the chain saw until sufficient chain oil has
reached the chain.See instructions under the heading
Lubricating cutting equipment.
Never use a machine, battery or battery charger that is
faulty. Carry out the checks, maintenance and service
instructions described in this manual. Some
maintenance and service measures must be carried out
by trained and qualified specialists. See instructions
under the heading Maintenance.
•
•
Check that the cutting equipment is correctly fitted and
adjusted. See instructions under the heading
Assembly.
Long-term exposure to noise can result in permanent
hearing impairment. So always use approved hearing
protection.
Never use any accessories other than those
recommended in this manual. See instructions under
the headings Cutting equipment and Technical data.
WARNING! Under no circumstances may
CAUTION! Always wear protective glasses or a face
visor to reduce the risk of injury from thrown objects. A
chain saw is capable of throwing objects, such as wood
chips, small pieces of wood, etc, at great force.This can
result in serious injury, especially to the eyes.
the design of the machine be modified
without the permission of the
manufacturer. Always use original
accessories. Non-authorized
!
modifications and/or accessories can
result in serious personal injury or the
death of the operator or others.
WARNING! Faulty cutting equipment or
the wrong combination of bar and saw
!
chain increases the risk of kickback!
Only use the bar/saw chain combinations
we recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
WARNING! A chain saw is a dangerous
tool if used carelessly or incorrectly and
!
can cause serious, even fatal injuries. It
is very important that you read and
understand the contents of this
operator’s manual.
Always use common sense
It is not possible to cover every conceivable situation you
can face when using a chain saw. Always exercise care
and use your common sense. Avoid all situations which
you consider to be beyond your capability. If you still feel
uncertain about operating procedures after reading these
instructions, you should consult an expert before
WARNING! Long term inhalation of chain
oil mist and dust from sawdust can
represent a health risk.
!
continuing. Do not hesitate to contact your dealer or us if
English – 9
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
you have any questions about the use of the chain saw.
Generally clothes should be close-fitting without
We will willingly be of service and provide you with advice
as well as help you to use your chain saw both efficiently
and safely.
restricting your freedom of movement.
IMPORTANT! Sparks can come from the bar and chain
or other sources. Always have fire extinguishing tools
available if you should need them. Help prevent forest
fires.
This top handle chainsaw is designed specifically for tree
surgery and maintenance in the tree. Due to the special
compact handle design (closely spaced handles), there is
an increased risk of losing control. For this reason these
special chainsaws should be used only for work in a tree
by persons who are trained in special cutting and working
techniques and who are properly secured (lift bucket,
ropes, safety harness). Regular chainsaws (with wider
spaced handles) are recommended for all other cutting
work at ground level.
Work is constantly in progress to improve the design and
technology - improvements that increase your safety and
efficiency. Visit your dealer regularly to see whether you
can benefit from new features that have been introduced.
Personal protective equipment
WARNING! Working in a tree requires the
WARNING! Most chain saw accidents
use of special cutting and working
!
happen when the chain touches the
techniques which must be observed in
order to reduce the increased risk of
personal injury. Never work in a tree
unless you have received specific,
professional training for such work,
including training in the use of safety
and other climbing equipment, such as
harnesses, ropes, belts, climbing irons,
snap hooks, carabiners, etc.
!
operator.You must use approved
personal protective equipment whenever
you use the machine. Personal protective
equipment cannot eliminate the risk of
injury but it will reduce the degree of
injury if an accident does happen. Ask
your dealer for help in choosing the right
equipment.
′
Machine s safety equipment
In this section the machine’s safety features and their
function are explained. For inspection and maintenance
see instructions under the heading Checking, maintaining
and servicing chain saw safety equipment. See
instructions under the heading, What is what?, to find
where these parts are located on your machine.
The life span of the machine can be reduced and the risk
of accidents can increase if machine maintenance is not
carried out correctly and if service and/or repairs are not
carried out professionally. If you need further information
please contact your nearest service workshop.
•
•
•
•
•
•
•
Approved protective helmet
Hearing protection
Protective goggles or a visor
Gloves with saw protection
Trousers with saw protection
Use appropriate protections for arm.
WARNING! Never use a machine with
defective safety components. Safety
equipment must be inspected and
maintained. See instructions under the
heading Checking, maintaining and
servicing chain saw safety equipment. If
your machine does not pass all the
checks, take the saw to a servicing
dealer for repair.
Boots with saw protection, steel toe-cap and non-slip
sole
•
•
Always have a first aid kit nearby.
Fire Extinguisher and Shovel
10 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
The brake is applied when the front hand guard (B) is
pushed forwards.
Keypad
Make sure the machine is switched on or off when the
activate/deactivate button (1) is pressed and held (>1
sec.). The green LED (2) is lit or turned off.
B
The warning indicator (3) flashes if the chain brake is
activated or if there is a risk of overload. The overload
protection temporarily deactivates the machine.When the
machine is restored to normal temperature it is again
ready for use. Solid light indicates need for service.
•
•
This movement activates a spring-loaded mechanism
that stops the drive sprocket.
(3)
The front hand guard is not designed solely to activate
the chain brake. Another important feature is that it
reduces the risk of your left hand hitting the chain if
you lose grip of the front handle.
(2)
(1)
Automatic switch off functionality
The machine is equipped with an automatic shutdown
feature that deactivates the machine if not used. The
machine will deactivate after 2 minutes.
•
Use the chain brake as a ”parking brake” when
starting and when moving over short distances, to
reduce the risk of moving chain accidentally hitting
your leg or anyone or anything close by.
Chain brake and front hand guard
Your chain saw is equipped with a chain brake that is
designed to stop the chain if you get a kickback.The chain
brake reduces the risk of accidents, but only you can
prevent them.
Take care when using your saw and make sure the
kickback zone of the bar never touches any object.
•
To release the chain brake pull the front hand guard
backwards, towards the front handle.
•
The chain brake (A) can either be activated manually
(by your left hand) or automatically by the inertia
release mechanism.
•
Kickback can be very sudden and violent. Most
kickbacks are minor and do not always activate the
chain brake. If this happens you should hold the chain
saw firmly and not let go.
A
English – 11
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
The way the chain brake is activated, either manually
There are also certain positions in which your hand
cannot reach the front hand guard to activate the chain
brake; for example, when the saw chain is held in felling
position.
or automatically by the inertia release mechanism,
depends on the force of the kickback and the position
of the chain saw in relation to the object that the
kickback zone of the bar strikes.
Will my inertia activated chain brake
always activate during kickback in the
event of a kickback?
If you get a violent kickback while the kickback zone of
the bar is farthest away from you the chain brake is
designed to be activated by the inertia in the kickback
direction.
No. First your brake must be in working order. Second the
kickback must be strong enough to activate the chain
brake. If the chain brake is too sensitive it would activate
all the time which would be a nuisance.
Will my chain brake always protect me
from injury in the event of a kickback?
No. First, the chain brake must be in working order to
provide the intended protection. Second, it must be
activated during the kickback as described above to stop
the saw chain.Third, the chain brake may be activated but
if the bar is too close to you the brake might not have
enough time to slow down and stop the chain before the
chain saw hits you.
If the kickback is less violent or the kickback zone of
the bar is closer to you the chain brake will be
activated manually by the movement of your left hand.
Only you and proper working technique can eliminate
kickback and its danger.
Throttle lockout
The power trigger lockout is designed to prevent
accidental operation of the power trigger.When you press
the power trigger lockout (A) (i.e when you grasp the
handle) it releases the power trigger (B). When you
release the handle the power trigger and the power trigger
lockout both move back to their original positions.
•
In the felling position the left hand is in a position that
makes manual activation of the chain brake
impossible. With this type of grip, that is when the left
hand is placed so that it cannot affect the movement
of the front hand guard, the chain brake can only be
activated by the inertia action.
A
B
Chain catcher
Will my hand always activate the chain
brake during a kickback?
The chain catcher is designed to catch the chain if it snaps
or jumps off. This should not happen if the chain is
properly tensioned (see instructions under the heading
Assembly) and if the bar and chain are properly serviced
No. It takes a certain force to move the hand guard
forward. If your hand only lightly touches the front guard
or slips over it, the force may not be enough to trigger the
chain brake.You should also maintain a firm grip of the
chain saw handles while working. If you do and
experience a kickback, your hand may never leave the
front handle and will not activate the chain brake, or the
chain brake will only activate after the saw has swung
around a considerable distance. In such instances, the
chain brake might not have enough time to stop the saw
chain before it touches you.
12 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
and maintained (see instructions under the heading
battery must not be used as a power source for other
General working instructions).
devices.
WARNING! Protect the battery from
direct sunlight, heat or open flame.There
is a risk the battery may explode if it is
thrown into an open fire.There is a risk of
burns and/or chemical burns.
Vibrations
Cutting hardwoods (most broadleaf trees) creates more
vibration than cutting softwoods (most conifers). Cutting
with cutting equipment that is blunt or faulty (wrong type
or badly sharpened) will increase the vibration level.
WARNING! Avoid all skin contact with
battery acid. Battery acid may cause skin
irritation, burns or corrosive injuries. If
you get acid in your eyes, do not rub but
flush your eyes with plenty of water for at
least 15 minutes. See a doctor.You must
wash any exposed skin with copious
amounts of water and soap in case of
incidental contact.
WARNING! Overexposure to vibration
can lead to circulatory damage or nerve
!
damage in people who have impaired
circulation. Contact your doctor if you
experience symptoms of overexposure
to vibration. Such symptoms include
numbness, loss of feeling, tingling,
pricking, pain, loss of strength, changes
in skin colour or condition.These
symptoms normally appear in the
fingers, hands or wrists.These
WARNING! Never connect the battery
terminal to keys, coins, screws or other
metal as this may short-circuit the
battery. Never insert objects into the
battery's air vents.
Unused batteries must be kept away from
metal objects such as nails, coins,
jewellery. Do not try to disassemble or
crush the battery
symptoms may be increased in cold
temperatures.
•
•
•
Use the battery in surroundings where temperatures
are between -10 °C and 40 °C.
Battery and battery charger
This section describes the battery and battery charger
safety for your battery product.
Do not expose the battery to microwaves or high
pressure.
Never clean the battery or the battery charger with
water. See also instructions under the Maintenance
heading.
Only use Husqvarna original batteries for Husqvarna
products and only charge them in an original battery
charger from Husqvarna. The batteries are software
encrypted.
•
•
Store the battery out of reach of children.
Protect the battery from rain and wet conditions.
Battery safety
The rechargeable Husqvarna batteries, BLi, are
exclusively used as a power supply for the relevant
Husqvarna cordless appliances. To avoid injury, the
English – 13
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Use the battery charger only when the surrounding
Battery charger safety
temperature is between 5 °C and 40 °C. Use the charger
in an environment which is well ventilated, dry and free
from dust.
Only use Chargers, Husqvarna QC, for charging the
Husqvarna replacement batteries, BLi.
Cutting equipment
This section describes how to choose and maintain your
cutting equipment in order to:
•
•
Reduce the risk of kickback.
Reduce the risk of the saw chain breaking or jumping
off the bar.
WARNING! Minimise the risk of electric
shock or short circuit as follows:
•
•
•
Obtain optimal cutting performance.
Extend the life of cutting equipment.
Avoid increasing vibration levels.
!
Never insert any object into the charger’s
cooling slots.
General rules
Do not try to dismantle the battery
charger.
•
Only use cutting equipment recommended by us!
See instructions under the heading Technical data.
Never connect the charger terminals to
metal objects as this can short circuit the
battery charger.
Use approved and intact wall sockets.
•
Keep the chain’s cutting teeth properly
•
•
•
Regularly check that the battery charger connection
wire is intact and that there are no cracks in it.
sharpened! Follow our instructions and use the
recommended file gauge. A damaged or badly
sharpened chain increases the risk of accidents.
Never carry the battery charger using the cord and
never pull out the plug by pulling the cord.
Keep all cables and extension leads away from water,
oil and sharp edges. Make sure the cable is not
jammed in doors, fences or the like. Otherwise it can
cause the charger to become live.
•
Maintain the correct depth gauge setting! Follow
our instructions and use the recommended depth
gauge clearance. Too large a clearance increases
the risk of kickback.
WARNING! Do not use the battery
charger close to corrosive or flammable
!
materials. Do not cover the battery
charger. Pull out the plug to the battery
charger in the event of smoke or fire.
Remember the risk of fire.
Do not use:
a faulty or damaged battery charger or never use a
faulty, damaged or deformed battery.
•
•
Keep the chain properly tensioned! If the chain is
slack it is more likely to jump off and lead to increased
wear on the bar, chain and drive sprocket.
•
Keep cutting equipment well lubricated and
properly maintained! A poorly lubricated chain is
more likely to break and lead to increased wear on the
bar, chain and drive sprocket.
Do not charge:
•
non-rechargeable batteries in the battery charger or
use them in the machine.
•
•
•
the battery in the battery charger outdoors.
the battery in the rain or in wet conditions.
the battery in direct sunlight.
14 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
•
•
Number of drive links. The number of drive links is
determined by the length of the bar, the chain pitch
and the number of teeth on the bar tip sprocket.
Cutting equipment designed to reduce
kickback
WARNING! Faulty cutting equipment or
the wrong combination of bar and saw
!
chain increases the risk of kickback!
Only use the bar/saw chain combinations
we recommend, and follow the filing
instructions. See instructions under the
heading Technical data.
Bar groove width (inches/mm). The groove in the bar
must match the width of the chain drive links.
The only way to avoid kickback is to make sure that the
kickback zone of the bar never touches anything.
By using cutting equipment with ”built-in” kickback
reduction and keeping the chain sharp and well-
maintained you can reduce the effects of kickback.
Guide bar
The smaller the tip radius the lower the chance of
kickback.
Chain oil hole and hole for chain tensioner. The bar
must be matched to the chain saw design.
Saw chain
A chain is made up of a number of links, which are
available in standard and low-kickback versions.
Saw chain
IMPORTANT! No saw chain design eliminates the
danger of kickback.
•
•
•
Chain pitch (inches)
WARNING! Any contact with a rotating
saw chain can cause extremely serious
injuries.
!
Drive link width (mm/inches)
Number of drive links.
Some terms that describe the bar and chain
To maintain the safety features of the cutting equipment,
you should replace a worn or damaged bar or chain with
a bar and chain combinations recommended by
Husqvarna. See instructions under the heading Technical
Data for a list of replacement bar and chain combinations
we recommend.
Guide bar
•
Length (inches/cm)
•
Number of teeth on bar tip sprocket (T).
Sharpening your chain and adjusting
depth gauge setting
General information on sharpening cutting teeth
•
Chain pitch (inches). The spacing between the drive
links of the chain must match the spacing of the teeth
on the bar tip sprocket and drive sprocket.
•
Never use a blunt chain. When the chain is blunt you
have to exert more pressure to force the bar through
the wood and the chips will be very small. If the chain
is very blunt it will produce wood powder and no chips
or shavings.
English – 15
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
•
A sharp chain eats its way through the wood and
produces long, thick chips or shavings.
gauge. This will help you obtain the maximum kickback
reduction and cutting performance from your chain.
See instructions under the heading Technical data for
information about sharpening your chain.
•
The cutting part of the chain is called the cutter and
consists of a cutting tooth (A) and the depth gauge
(B). The cutters cutting depth is determined by the
difference in height between the two (depth gauge
setting).
WARNING! Departure from the
sharpening instructions considerably
increases the risk of kickback.
!
Sharpening cutting teeth
Li-ion
To sharpen cutting teeth you will need a round file and a
file gauge. See instructions under the heading Technical
data for information on the size of file and gauge that are
recommended for the chain fitted to your chain saw.
When you sharpen a cutting tooth there are four important
factors to remember.
1
Filing angle
•
•
Check that the chain is correctly tensioned. A slack
chain will move sideways, making it more difficult to
sharpen correctly.
2
Cutting angle
3
4
File position
Always file cutting teeth from the inside face. Reduce
the pressure on the return stroke. File all the teeth on
one side first, then turn the chain saw over and file the
teeth on the other side.
Round file diameter
It is very difficult to sharpen a chain correctly without the
right equipment. We recommend that you use our file
•
File all the teeth to the same length. When the length
of the cutting teeth is reduced to 4 mm (5/32") the
chain is worn out and should be replaced.
16 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
General advice on adjusting depth gauge setting
Tensioning the chain
•
When you sharpen the cutting tooth (A) the depth
gauge setting (C) will decrease. To maintain optimal
cutting performance the depth gauge (B) has to be
filed down to achieve the recommended depth gauge
setting. See instructions under the heading Technical
data to find the correct depth gauge setting for your
particular chain.
Li-ion
WARNING! A slack chain may jump off
and cause serious or even fatal injury.
!
!
WARNING! Always remove the battery
before any assembly, maintenance and/
or checking is done on the machine.
The more you use a chain the longer it becomes. It is
therefore important to adjust the chain regularly to take up
the slack.
WARNING! The risk of kickback is
increased if the depth gauge setting is
too large!
!
Check the chain tension every time you refill with saw
chain oil. NOTE! A new chain has a running-in period
during which you should check the tension more
frequently.
Adjustment of depth gauge setting
Li-ion
Tension the chain as tightly as possible, but not so tight
that you cannot pull it round freely by hand.
•
•
The cutting teeth should be newly sharpened before
adjusting the depth gauge setting. We recommend
that you adjust the depth gauge setting every third
time you sharpen the cutting teeth. NOTE! This
recommendation assumes that the length of the
cutting teeth is not reduced excessively.
You will need a flat file and a depth gauge tool. We
recommend that you use our depth gauge tool to
acheive the correct depth gauge setting and bevel for
the depth gauge.
•
Loosen the bar nut that holds the clutch cover and
chain brake. Use the combination spanner.
•
Place the depth gauge tool over the chain. Detailed
information regarding the use of the depth gauge tool,
will be found on the package for the depth gauge tool.
Use the flat file to file off the tip of the depth gauge that
protrudes through the depth gauge tool. The depth
gauge setting is correct when you no longer feel
resistance as you draw the file along the depth gauge
tool.
•
Raise the tip of the bar and stretch the chain by
tightening the chain tensioning screw using the
combination spanner. Tighten the chain until it does
not sag from the underside of the bar.
•
Use the combination spanner to tighten the bar nut
while holding up the tip of the bar. Check that you can
English – 17
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
pull the saw chain round freely by hand, and that there
Checking chain lubrication
is no slack on the underside of the bar.
•
Check the chain lubrication every third battery charge.
See instructions under the heading Lubricating the
bar tip sprocket. See instructions under the heading
Lubricating the bar tip sprocket.
Aim the tip of the bar at a light coloured surface about
20 cm (8 inches) away. After 1 minute running at 3/4
throttle you should see a distinct line of oil on the light
surface.
The position of the chain tensioning screw on our chain
saws varies from model to model. See instructions under
the heading What is what? to find out where it is on your
model.
Lubricating cutting equipment
WARNING! Poor lubrication of cutting
equipment may cause the chain to snap,
which could lead to serious, even fatal
injuries.
!
Chain oil
Chain oil must demonstrate good adhesion to the chain
and also maintain its flow characteristics regardless of
whether it is warm summer or cold winter weather.
If the chain lubrication is not working:
Never use waste oil! Using waste oil can be dangerous
to you and damage the machine and environment.
•
Check that the oil channel in the bar is not obstructed.
Clean if necessary.
IMPORTANT! When using vegetable based saw chain
oil, dismantle and clean the groove in the bar and saw
chain before long-term storage.Otherwise there is a risk
of the saw chain oil oxidizing, which will result in the saw
chain becoming stiff and the bar tip sprocket jamming.
Filling with chain oil
•
Check that the groove in the edge of the bar is clean.
Clean if necessary.
•
All our chain saws have an automatic chain lubrication
system. On some models the oil flow is also
adjustable.
•
Check that the bar tip sprocket turns freely and that
the lubricating hole in the tip sprocket is not blocked.
Clean and lubricate if necessary.
•
The saw chain oil tank is designed to last aproximately
three battery charges. However, this safety feature
requires that you use the right sort of chain oil (if the
chain oil is to thin it will last shorter time).
•
•
•
Never use waste oil. This results in damage to the oil
pump, the bar and the chain.
It is important to use oil of the right grade (suitable
viscosity range) to suit the air temperature.
If the chain lubrication system is still not working after
carrying out the above checks and associated measures
you should contact your service agent.
In temperatures below 0°C (32°F) some oils become
too viscous.This can overload the oil pump and result
in damage to the oil pump components.
•
Contact your service agent when choosing chain oil.
18 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
GENERAL SAFETY PRECAUTIONS
Chain drive sprocket
•
Whether the tip of the bar is uneven or badly worn. If
a hollow forms on the underside of the bar tip this is
due to running with a slack chain.
Li-ion
The drive system is fitted with a drive sprocket.
•
To prolong the life of the bar you should turn it over
daily.
Regularly check the degree of wear on the drive sprocket.
Replace if wear is excessive.
WARNING! Most chain saw accidents
happen when the chain touches the
operator.
Checking wear on cutting equipment
Li-ion
Wear personal protective equipment. See
instructions under the ”Personal
protective equipment” heading.
Check the chain daily for:
Do not tackle any job that you feel you
are not adequately trained for. See
instructions under the headings
Personal protective equipment, How to
avoid kickback, Cutting equipment and
General working instructions.
•
•
•
Visible cracks in rivets and links.
Whether the chain is stiff.
Avoid situations where there is a risk of
kickback. See instructions under the
Whether rivets and links are badly worn.
Replace the saw chain if it exhibits any of the points
above.
′
heading Machine s safety equipment.
Use the recommended protective
equipment and check its condition. See
instructions under the headings
Technical data and General safety
precautions.
We recommend you compare the existing chain with a
new chain to decide how badly the existing chain is worn.
When the length of the cutting teeth has worn down to
only 4 mm the chain must be replaced.
Guide bar
Check that all the chain saw safety
features are working. See instructions
under the headings General working
instructions and General safety
precautions.
Li-ion
Check regularly:
Never use a chain saw by holding it with
one hand. A chain saw is not safely
controlled with one hand. Always have a
secure, firm grip around the handles with
both hands.
•
Whether there are burrs on the edges of the bar.
Remove these with a file if necessary.
•
Whether the groove in the bar has become badly
worn. Replace the bar if necessary.
English – 19
Download from Www.Somanuals.com. All Manuals Search And Download.
ASSEMBLY
sprocket and that the saw chain is in the groove in the
guide bar. Tighten the bar nut finger-tight.
Fitting the bar and chain
Li-ion
WARNING! Always remove the battery
before any assembly, maintenance and/
or checking is done on the machine.
!
!
WARNING! Always wear gloves, when
working with the chain.
•
•
Tension the chain by turning the chain tensioning
screw clockwise using the combination spanner. The
chain should be tensioned until it does not sag from
the underside of the bar. See instructions under the
heading Tensioning the chain.
•
Check that the chain brake is in disengaged position
by moving the front hand guard towards the front
handle.
The chain is correctly tensioned when there is no
slack on the underside of the bar, and it can still be
turned easily by hand. Tighten the bar nut with the
combination spanner while holding up the tip of the
bar.
•
Unscrew the bar nut and remove the drive sprocket
cover. Remove the transportation guard (A).
•
When fitting a new chain, the chain tension has to be
checked frequently until the chain is run-in. Check the
chain tension regularly. A correctly tensioned chain
ensures good cutting performance and long life.
A
•
Fit the bar over the bar bolt. Place the bar in its
rearmost position. Place the chain over the drive
sprocket and in the groove on the bar.Begin on the top
side of the bar.
Fitting a spike bumper
To fit a spike bumper – contact your service agent.
•
•
Make sure that the edges of the cutting links are facing
forward on the top edge of the bar.
Fit the drive sprocket cover and locate the chain
adjuster pin in the cut-out in the guide bar. Check that
the drive links of the saw chain fit correctly on the drive
20 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY HANDLING
Connect the battery to the battery charger
Battery status
Regularly check that the battery charger and the battery
are intact. See also instructions under the Maintenance
heading.
The display shows the battery capacity and if there are
any problems with the battery. The battery capacity is
displayed for 5 seconds after the machine is switched off
or the battery indicator button is pressed. The warning
symbol on the battery is lit when an error has occurred.
See fault codes.
The battery must be charged before using it the first time.
The battery is only 30% charged when delivered.
•
Put the battery in the battery charger. Make sure that
the battery is connected to the battery charger.
1
2
3
4
LED lights
Battery status
All LEDs are lit
Fully charged (75-100%).
The battery is 50%-75%
charged.
•
The green charging light on the charger is lit when the
battery is connected to the battery charger.
LED 1, LED 2, LED 3 are lit.
LED 1, LED 2 are lit.
LED 1 is lit.
The battery is 25%-50%
charged.
The battery is 0%-25%
charged.
The battery is empty.
Charge the battery.
LED 1 flashes
•
When all LEDs are lit the battery is fully charged.
Battery charger
2
1
4
3
WARNING! Risk of electric shock and
short circuiting. Use approved and intact
wall sockets. Make sure that the cable is
not damaged. Replace cable if it appears
to be damaged in any way.
!
•
•
Pull out the plug. Never jerk the power supply cable to
disconnect it from the wall socket.
Connect the battery charger
•
Connect the battery charger to the voltage and
frequency specified on the rating plate.Put the electric
plug in a earthed socket-outlet. The LED on the
battery charger flashes green once.
Remove the battery from the battery charger.
Charging status
Lithium-ion batteries can be charged at whatever
charging level.The charging process can be cancelled or
started whatever the battery’s charge level is. A fully
charged battery will not lose its charge even when the
battery is left in the charger. Remove a fully charged
battery from the battery charger.
2
1
4
3
•
The battery will not be charged if the battery
temperature is over 50 °C. In that case the battery
charger will actively cool down the battery.
English – 21
Download from Www.Somanuals.com. All Manuals Search And Download.
BATTERY HANDLING
Disposal of the battery, battery
LED display
Charging status
charger and machine
The battery is 0%-
25% charged.
LED 1 flashes
Symbols on the product or its packaging indicate that this
product cannot be handled as domestic waste. It must
instead be submitted to an appropriate recycling station
for the recovery of electrical and electronic equipment.
The battery is 25%-
50% charged.
LED 1 is lit, LED 2 flashes.
The battery is 50%-
75% charged.
LED 1, LED 2 are lit, LED 3 flashes
By ensuring that this product is taken care of correctly, you
can help to counteract the potential negative impact on
the environment and people that can otherwise result
through the incorrect waste management of this product.
For more detailed information about recycling this
product, contact your municipality, your domestic waste
service or the shop from where you purchased the
product.
LED 1, LED 2, LED 3 are lit, LED 4 Battery is 75%-
flashes
100% charged
When all the LEDs
LED 1, LED 2, LED 3, LED 4 are lit. are lit on the battery,
it is fully charged.
Transport and storage
•
The contained lithium-ion-batteries are subject to the
Dangerous Goods Legislation requirements.
•
For commercial transports e.g. by third parties,
forwarding agents, special requirement on packing
and labeling must be observed.
Li-ion
•
•
For preparation of the item being shipped, consulting
an expert for hazardous material is required. Please
also observe possibly more detailed national
regulations.
Tape or mask off open contacts and pack up the
batteriy in such a manner that it cannot move around
in the packing.
•
•
Always remove the battery for storage or transport.
Store the battery and the battery charger in a dry,
moisture-free and frost-free space.
•
•
Do not store the battery in places where static
electricity can occur.Never store the battery in a metal
box.
Store the battery and the battery charger where the
temperature is between 5 °C and 45 °C and never in
direct sunlight.
•
•
Store the battery charger only in an enclosed and dry
space.
Be sure to store the battery separate from the battery
charger. Store the equipment in a lockable area so
that it is out of reach of children and unauthorized
persons.
•
•
Ensure the machine is cleaned and that a complete
service is carried out before long-term storage.
The guide bar cover must always be fitted to the
cutting attachment when the machine is being
transported or in storage, in order to prevent accident
contact with the sharp chain. Even a non-moving
chain can cause serious cuts to yourself or persons
you bump into with an exposed chain.
•
Secure the machine during transport.
22 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
•
Always hold the saw with both hands. The right hand
Starting and stopping
should be on the top handle, and the left hand on the
front handle. All people, whether right or left handed,
should use this grip. Use a firm grip with thumbs and
fingers encircling the chain saw handles.
WARNING! Note the following before
starting:
!
Never start a chain saw unless the bar,
chain and all covers are fitted correctly.
Otherwise the drive sprocket can come
loose and cause personal injuries.
Make sure you have a secure footing and
that the chain cannot touch anything.
If you need to start the chain saw in the
tree, see instructions under the heading
Starting the saw in the tree, under the
section Working techniques.
Starting
•
Insert the battery in the machine. The battery should
Keep people and animals well away from
the working area.
slide easily into the battery holder on the machine. If
the battery does not slide in easily, it is not being
inserted correctly.
•
•
•
Before inserting the battery into the machine, always
check to see that the power trigger actuates properly
and returnes to the ”OFF” position when released. To
prevent the power trigger from being accidentally
pulled, a power trigger lockout is provided.
Never start a chain saw unless the bar, chain and all
covers are fitted correctly. See instructions under the
heading Assembly.
•
Press on the lower part of the battery and push it in as
far as it will go into the battery compartment. Make
sure the latches snap in place properly.
Observe your surroundings and make sure that there
is no risk of people or animals coming into contact with
the cutting equipment.
•
Press and hold the start button (>1 sec.) until the
green LED is lit.
English – 23
Download from Www.Somanuals.com. All Manuals Search And Download.
STARTING AND STOPPING
Stopping
The machine is deactivated by pressing the start/stopp
button on the keypad (green LED off).
Note! To avoid involuntary start up, the battery must
always be removed when the machine is not in use or is
unsupervised.To remove the battery, withdraw it from the
machine while pressing the battery release buttons on the
battery.
24 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Before use:
General working instructions
1
IMPORTANT!
3
9
2
This section describes basic safety rules for using a
chain saw. This information is never a substitute for
professional skills and experience. If you get into a
situation where you feel unsafe, stop and seek expert
advice. Contact your chain saw dealer, service agent or
an experienced chain saw user. Do not attempt any task
that you feel unsure of!
4
7
8
5
6
Before using a chain saw you must understand the
effects of kickback and how to avoid them. See
instructions under the heading How to avoid kickback.
1
2
3
Check that the chain brake works correctly and is not
damaged.
Check that the power trigger lockout works correctly
and is not damaged.
Before using a chain saw you must understand the
difference between cutting with the top and bottom
edges of the bar. See instructions under the headings
How to avoid kickback and Machine’s safety equipment.
Check that the keypad works correctly and is not
damaged.
4
5
Check that all handles are free from oil.
Wear personal protective equipment. See instructions
under the ”Personal protective equipment” heading.
Check that all parts of the chain saw are tightened
correctly and that they are not damaged or missing.
6
Check that the chain catcher is in place and not
damaged.
During tree maintenance work above ground level the
chain saw must be secured. Secure the chain saw by
attaching a safety line to the rope eyelet on the chain saw.
7
8
Check the chain tension.
Check that the battery is fully charged and securely
attached in the chain saw.
9
Check that the saw chain stops moving when the
power trigger is released.
SavE
The machine is equipped with a power saving function
(savE). This function is activated by pressing the savE
button on the keypad. With savE activated the runtime of
the machine is prolonged as the chain speed is reduced.
Basic safety rules
1
•
Look around you:
To ensure that people, animals or other things cannot
affect your control of the machine.
•
To make sure that none of the above might come
within reach of your saw or be injured by falling trees.
Note! Using the machine with SavE activated only
reduces the chain speed not the cutting power of the
machine.
CAUTION! Follow the instructions above, but do not use a
chain saw in a situation where you cannot call for help in
case of an accident.
2
All tree maintenance work above ground level must be
carried out by two or more persons with the right
training (see instructions under the heading
Important). At least one person should be on the
English – 25
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
ground to carry out safe rescue procedures and/or get
help should an emergency arise.
saw with the bar and chain pointing backwards. Fit a
guard to the bar before transporting the chain saw or
carrying it for any distance.
3
4
5
During tree maintenance work above ground level, the
working area should always be secured and marked
out with signs, tape or the like. The person(s) on the
ground should always inform the person(s) working
above before they enter the secure working area.
Do not use the machine in bad weather, such as
dense fog, heavy rain, strong wind, intense cold, etc.
Working in bad weather is tiring and often brings
added risks, such as icy ground, lightning,
unpredictable felling direction, etc.
Take great care when removing small branches and
avoid cutting bushes (i.e.cutting many small branches
at the same time). Small branches can be grabbed by
the chain and thrown back at you, causing serious
injury.
9
When you put the chain saw on the ground, lock the
saw chain using the chain brake and ensure you have
a constant view of the machine. Deactivate the
machine and remove the battery before leaving your
chain saw for any length of time.
General rules
1
If you understand what kickback is and how it happens
then you can reduce or eliminate the element of
surprise. By being prepared you reduce the risk.
Kickback is usually quite mild, but it can sometimes be
very sudden and violent.
6
Make sure you can move and stand safely. Check the
area around you for possible obstacles (roots, rocks,
branches, ditches, etc.) in case you have to move
suddenly. Take great care when working on sloping
ground.
2
Always hold the chain saw firmly with your right hand
on the top handle and your left hand on the front
handle. Wrap your fingers and thumbs around the
handles.You should use this grip whether you are
right-handed or left-handed. This grip minimises the
effect of kickback and lets you keep the chain saw
under control. Do not let go of the handles!
7
Take great care when cutting a tree that is in tension.
A tree that is in tension may spring back to its normal
position before or after being cut. If you position
yourself incorrectly or make the cut in the wrong place
the tree may hit you or the machine and cause you to
lose control. Both situations can cause serious
personal injury.
3
Most kickback accidents happen during limbing.Make
sure you are standing firmly and that there is nothing
in the way that might make you trip or lose your
balance.
Lack of concentration can lead to kickback if the
kickback zone of the bar accidentally touches a
branch, nearby tree or some other object.
WARNING! Sometimes chips get stuck in
the drive system causing the saw chain
!
to jam. Always deactivate the machine
and remove the battery before any
cleaning.
Have control over the workpiece. If the pieces you
intend to cut are small and light, they can jam in the
saw chain and be thrown towards you. Even if this
8
Before moving your chain saw deactivate it and lock
the saw chain using the chain brake. Carry the chain
26 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
does not need to be a danger, you may be surprised
8
Unless the user resists this pushing force there is a
and lose control of the saw. Never saw stacked logs or
branches without first separating them. Only saw one
log or one piece at a time. Remove the cut pieces to
keep your working area safe.
risk that the chain saw will move so far backwards that
only the kickback zone of the bar is in contact with the
tree, which will lead to a kickback.
4
Never use the chain saw above shoulder height
and try not to cut with the tip of the bar. Never use
the chain saw one-handed!
Cutting with the bottom edge of the bar, i.e. from the
top of the object downwards, is known as cutting on
the pull stroke. In this case the chain saw pulls itself
towards the tree and the front edge of the chain saw
body rests naturally on the trunk when cutting. Cutting
on the pull stroke gives the operator better control over
the chain saw and the position of the kickback zone.
5
6
Always use a fast cutting speed, i.e. full throttle.
9
Follow the instructions on sharpening and maintaining
your bar and chain. When you replace the bar and
chain use only combinations that are recommended
by us. See instructions under the headings Cutting
equipment and Technical data.
If you have to cut branches or the like that are above
shoulder height, a working platform or scaffold tower
is recommended.
Working with tree service chain-saws
from a rope and harness
This chapter sets out working practices to reduce the risk
of injury from tree service chainsaws when working at
height from a rope and harness. While it may form the
basis of guidance and training literature, it should not be
regarded as a substitute for formal training.
General requirements working at height
Operators of tree service chainsaws working at height
from a rope and harness should never work alone. A
competent ground worker trained in appropriate
emergency procedures should assist them.
Operators of tree service chainsaws for this work should
be trained in general safe climbing and work positioning
techniques and shall properly equipped with harnesses,
ropes, strops, karabiners and other equipment for
maintaining secure and safe working positions for both
themselves and the saw.
7
Take great care when you cut with the top edge of the
bar, i.e. when cutting from the underside of the object.
This is known as cutting on the push stroke.The chain
tries to push the chain saw back towards the user. If
the saw chain is jamming, the saw may be pushed
back at you.
Preparing to use the saw in the tree
The chain saw should be checked by the ground worker
and the chain brake should be engaged before it is sent
up to the operator in the tree. The chain saw should be
fitted with a suitable strop for attaching to the operator’s
harness:
English – 27
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
a) attach the rope around the rope eyelet on the rear of the
•
hip level when cutting horizontal sections.
saw.
•
solar plexus level when cutting vertical sections.
Where the operator is working close into vertical stems
with a low lateral forces on their work position, then a good
footing may be all that is needed to maintain a secure
work position. However as operators move away from the
stem, they will need to take steps to remove or counteract
the increasing lateral forces by, for example, a re-direct of
the main line via a supplementary anchor point or using
an adjustable strop direct from the harness to a
supplementary anchor point.
b) provide suitable karabiners to allow indirect (i.e. via the
strop) and direct attachment (i.e. at the attachment point
on the saw) of saw to the operators harness.
Gaining a good footing at the working position can be
assisted by use of a temporary foot stirrup created from
an endless sling.
Starting the saw in the tree
The chain brake should always be engaged when
lowering a machine onto its strop. The operator should
always check that the battery is fully charged before
undertaking critical cuts.
One-hand use of the chainsaw
CAUTION! The belt eyelet is not dimensioned for use with
a so-called safety rope. Use the rope eyelet for this
purpose.
Operators should never use a chain saw onehanded.
Operators should never:
c) ensure the saw is securely attached when it is being
sent up to the operator.
•
cut with the kickback zone at the tip of the chainsaw
guide bar
d) ensure the saw is secured to the harness before it is
disconnected from the means of ascent.
•
•
•
‘hold and cut’ sections.
attempt to catch falling sections.
The saw should only be attached to the recommended
attachment points on the harness. These may be at mid-
point (front or rear) or at the sides. Where possible
attaching the saw to centre rear mid-point will keep it clear
of climbing lines and support its weight centrally down the
operator’s spine.
Cut in the tree when he/she is only secured with one
rope, always use 2 secured lines.
•
check condition of harness, belt and ropes at regular
frequent intervals.
Freeing a trapped saw
When moving the saw from any attachment point to
another, operators should ensure it is secured in the new
position before releasing it from the previous attachment
point.
If the saw should become trapped during cutting,
operators should:
•
switch off the saw and attach it securely to the tree
inboard (i.e. towards the truck side) of the cut or to a
separate tool line.
Using the chainsaw in the tree
An analysis of accidents with these saws during tree
service operations shows the primary cause as being
inappropriate one-handed use of the saw. In the vast
majority of accidents, operators fail to adopt a secure
work position witch allows them to hold both handles of
the saw. This results in an increased risk of injury due to:
•
•
pull the saw from the kerf whilst lifting the branch as
necessary.
if necessary, use a handsaw or second chain saw to
release the trapped saw by cutting a minimum of 30
cm away from the trapped saw.
Whether a handsaw or a chainsaw is used to free a stuck
saw, the release cuts should always be outboard (toward
the tips of the branch), in order to prevent the saw being
taken with the section and further complicating the
situation.
•
•
not having a firm grip on the saw if it kicks back.
a lack of control of the saw such that it is more liable
to contact climbing lines and operators body
(particularly the left hand and arm)
•
loosing control from insecure work position resulting
in contact with the saw (unexpected movement during
operation of the saw)
Securing the work position for two-handed use
To allow the operator to hold the saw with both hands,
they should as general rule, aim for secure work position
where they are operating the saw at:
28 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Two factors decide whether the chain will jam or the object
Basic cutting technique
that you are cutting will split: the first is how the object is
supported before and after cutting, and the second is
whether it is in tension.
WARNING! Never use a chain saw by
holding it with one hand. A chain saw is
not safely controlled with one hand; you
can cut yourself. Always have a secure,
firm grip around the handles with both
hands.
!
In most cases you can avoid these problems by cutting in
two stages; from the top and from the bottom.You need to
support the object so that it will not trap the chain or split
during cutting.
General
WARNING! If the saw chain jams in the
cut: deactivate the machine! Do not try to
!
•
•
Always use full throttle when cutting!
pull the machine free. If you do you may
be injured by the saw chain when the
machine suddenly brakes free. Use a
lever to open up the cut and free the
machine.
Let go of the power trigger after every cut (running the
motor for too long at full power without any load, i.e.
without any resistance from the chain during cutting,
can lead to serious damage to the motor).
•
•
Cutting from above = Cutting on the pull stroke.
Cutting from below = Cutting on the push stroke.
The following instructions describe how to handle the
commonest situations you are likely to encounter when
using a chain saw.
Cutting on the push stroke increases the risk of kickback.
See instructions under the heading How to avoid
kickback.
Cutting
The log is lying on the ground. There is little risk of the
chain jamming or the object splitting. However there is a
risk that the chain will touch the ground when you finish
the cut.
Terms
Cutting = General term for cutting through wood.
Limbing = Cutting branches off a felled tree.
Splitting = When the object you are cutting breaks off
before the cut is complete.
There are five important factors you should consider
before making a cut:
Cut all the way through the log from above. Avoid letting
the chain touch the ground as you finish the cut. Maintain
full throttle but be prepared for what might happen.
1
Make sure the cutting equipment will not jam in the
cut.
- If it is possible (can you turn the log?) stop cutting about
2/3 of the way through the log.
2
3
Make sure the object you are cutting will not split.
Make sure the chain will not strike the ground or any
other object during or after cutting.
- Turn the log and finish the cut from the opposite side.
4
5
Is there a risk of kickback?
The log is supported at one end. There is a high risk
that it will split.
Do the conditions and surrounding terrain affect how
safely you can stand and move about?
English – 29
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Start by cutting from below (about 1/3 of the way through).
utility line, the utility company should be notified
immediately.
During tree maintenance work above ground level, the
working area must always be secured and marked out
with signs, tape or the like.
Felling direction
The aim is to fell the tree in a position where you can limb
and cross-cut the log as easily as possible.You want it to
fall in a location where you can stand and move about
safely.
- Finish by cutting from above so that the two cuts meet.
Once you have decided which way you want the tree to fall
you must judge which way the tree would fall naturally.
Several factors affect this:
The log is supported at both ends. There is a high risk
•
•
•
•
•
Lean of the tree
Bend
that the chain will jam.
Wind direction
Arrangement of branches
Obstacles within the reach of the tree: for example,
other trees, power lines, roads and buildings.
- Start by cutting from above (about 1/3 of the way
through).
•
•
Look for signs of damage and rot in the stem, this
makes it more probably that the tree will break and
start to fall before you expect it to.
Weight of snow
- Finish by cutting from below so that the two cuts meet.
Tree felling technique
WARNING! It takes a lot of experience to
fell a tree. Inexperienced users of chain
saws should not fell trees. Do not
attempt any task that you feel unsure of!
!
You may find you are forced to let the tree fall in its natural
direction because it is impossible or dangerous to try to
make it fall in the direction you first intended.
Another very important factor, which does not affect the
felling direction but does affect your safety, is to make sure
the tree has no damaged or dead branches that might
break off and hit you during felling.
Safe distance
The safe distance between a tree that is to be felled and
anyone else working nearby is at least 2 1/2 tree lengths.
Make sure that no-one else is in this ”risk zone” before or
during felling.
The main point to avoid is letting the tree fall onto another
tree. It is very dangerous to remove a trapped tree and
there is high accident risk. See instructions under the
heading Freeing a tree that has fallen badly.
WARNING! During critical felling
operations, hearing protectors should be
lifted immediately when sawing is
completed so that sounds and warning
signals can be heard.
Trees should not be felled in a manner that would
endanger any person, strike any utility line or cause any
property damage. If the tree does make contact with any
30 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Clearing the trunk and preparing your retreat
to fall (2). Stand on the right-hand side of the tree, behind
the saw, and cut with a pull stroke.
Delimb the stem up to shoulder height. It is safer to work
from the top down and to have the tree between you and
the saw.
1
2
Next make the bottom cut so that it finishes exactly at the
end of the top cut.
Remove any undergrowth from the base of the tree and
check the area for obstacles (stones, branches, holes,
etc.) so that you have a clear path of retreat when the tree
starts to fall.Your path of retreat should be roughly 135
degrees away from the intended felling direction.
The directional cuts should run 1/4 of the diameter
through the trunk and the angle between the top cut and
bottom cut should be 60° - 70°.
1
3
2
1
1
2
The line where the two cuts meet is called the directional
cut line. This line should be perfectly horizontal and at
right angles (90°) to the chosen felling direction.
1
2
3
Danger zone
Retreat path
Felling direction
Felling
WARNING! Unless you have special
training we advise you not to fell trees
with a diameter larger than the bar length
of your saw!
!
Felling cut
The felling cut is made from the opposite side of the trunk
and it must be perfectly horizontal. Try to take a correct
position so you are able to cut on the pull stroke.
Felling is done using three cuts. First you make the
directional cuts, which consist of the top cut and the
bottom cut, then you finish with the felling cut. By placing
these cuts correctly you can control the felling direction
very accurately.
Make the felling cut about 0-3 cm (0-1.5 inches) above the
bottom directional cut.
Directional cuts
To make the directional cut you begin with the top cut.Aim
using to the saw’s felling direction mark (1) toward a goal
further forward in the terrain, where you would like the tree
Set the spike bumper (if one is fitted) just behind the felling
hinge. Use full throttle and advance the chain/bar slowly
into the tree. Make sure the tree-top does not start to
English – 31
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
move in the opposite direction to your intended felling
direction.
There are methods for felling trees with a diameter larger
than the bar length. However these methods involve a
much greater risk that the kickback zone of the bar will
come into contact with the tree.
Finish the felling cut parallel with the directional cut line so
that the distance between them is at least 1/10 of the
trunk diameter.The uncut section of the trunk is called the
felling hinge.
WARNING! Unless you have special
training we advise you not to fell trees
with a diameter larger than the bar length
of your saw!
!
Freeing a tree that has fallen badly
Freeing a ”trapped tree”
It is very dangerous to remove a trapped tree and there is
high accident risk.
The felling hinge controls the direction that the tree falls in.
Never work in the risk zone of the hanging trapped tree.
All control over the felling direction is lost if the felling
hinge is too narrow or non-existent, or if the directional
cuts and felling cut are badly placed.
The safest method is to use a winch.
•
•
Tractor-mounted
Portable
Cutting trees and branches that are in tension
When the felling cut and directional cut are complete the
tree should start to fall by itself or with the aid of a felling
wedge or breaking bar.
Preparations:
Work out which side is in tension and where the point of
maximum tension is (i.e. where it would break if it was
bent even more).
We recommend that you use a bar that is longer than the
diameter of the tree, so that you can make the felling cut
and directional cuts with single cutting strokes. See the
Technical data section to find out which lengths of bar are
recommended for your saw.
Decide which is the safest way to release the tension and
whether you are able to do it safely. In complicated
situations the only safe method is to put aside your chain
saw and use a winch.
General advice:
Position yourself so that you will be clear of the tree or
branch when the tension is released.
32 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
WORKING TECHNIQUES
Make one or more cuts at or near the point of maximum
was being used when the kickback zone of the bar
tension. Make as many cuts of sufficient depth as
necessary to reduce the tension and make the tree or
branch break at the point of maximum tension.
touched the object.
Never cut straight through a tree or branch that is in
tension!
If you must cut across tree/limb, make two to three cuts,
one inch apart, one to two inches deep.
Kickback only occurs if the kickback zone of the bar
touches an object.
Continue to cut deeper until tree/limb bends and tension
is released.
Cut tree/limb from outside the bend, after tension has
been released.
Limbing
WARNING! A majority of kickback
accidents occur during limbing. Do not
How to avoid kickback
use the kickback zone of the guide bar.
Be extremely cautious and avoid
contacting the log, other limbs or objects
with the nose of the guide bar. Be
extremely cautious of limbs under
tension.They can spring back toward
you and cause loss of control resulting
in injury.
WARNING! Kickback can happen very
suddenly and violently; kicking the chain
!
saw, bar and chain back at the user. If
this happens when the chain is moving it
can cause very serious, even fatal
injuries. It is vital you understand what
causes kickback and that you can avoid
it by taking care and using the right
working technique.
When limbing thick branches you should use the same
approach as for cutting.
What is kickback?
Cut difficult branches piece by piece.
The word kickback is used to describe the sudden
reaction that causes the chain saw and bar to jump off an
object when the upper quadrant of the tip of the bar,
known as the kickback zone, touches an object.
Kickback always occurs in the cutting plane of the bar.
Normally the chain saw and bar are thrown backwards
and upwards towards the user. However, the chain saw
may move in a different direction depending on the way it
Make sure that you can stand and move about safely.
Work on the left side of the trunk. Work as close as
possible to the chain saw for maximum control.If possible,
let the weight of the chain saw rest on the trunk.
Keep the trunk between you and the chain saw as you
move along the trunk.
Cutting the trunk into logs
See instructions under the heading Basic cutting
technique.
English – 33
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
•
Grasp the chain saw firmly, wrapping your fingers and
thumbs around the handles.
General
The user must only carry out the maintenance and
service work described in this Operator's Manual. More
extensive work must be carried out by an authorized
service workshop.
Checking, maintaining and
servicing chain saw safety
equipment
•
Apply full power and activate the chain brake by tilting
your left wrist forward onto the front hand guard. Do
not let go of the front handle. The chain should stop
immediately.
Note! All service and repair work on the machine
demands special training. This is especially true of the
machine’s safety equipment. If your machine fails any of
the checks described below we recommend that you
take it to your service workshop.
WARNING! Always remove the battery
before any assembly, maintenance and/
or checking is done on the machine.
!
Power trigger lockout
IMPORTANT! Never clean the battery or the battery
charger with water. Strong cleaning agents can damage
the plastic.
•
Make sure that the power trigger is locked at the idle
setting when the power trigger lockout is released.
Chain brake and front hand guard
Checking the front hand guard
Li-ion
•
Make sure the front hand guard is not damaged and
that there are no visible defects such as cracks.
•
Press the power trigger lockout and make sure it
returns to its original position when released.
•
Move the front hand guard forwards and back to make
sure it moves freely and that it is securely anchored to
the machine.
•
Check that the power trigger and power trigger lockout
move freely and that the return springs work properly.
Checking the brake trigger
•
Activate the chain saw and apply full power. Release
the power trigger and check that the saw chain stops
and remains stationary.
•
Activate the chain saw. Make sure the saw chain does
not touch the ground or any other object. See the
instructions under the heading Start and stop.
34 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Chain catcher
Battery connectors
Li-ion
Li-ion
•
Check that the chain catcher is not damaged and is
firmly attached to the body of the chain saw.
Clean the battery and the machines battery compartment
with a soft brush after use. Make sure all cooling slots and
battery connectors are cleaned.
Cooling system
Keypad
•
Activate the chain saw (green LED on) and make sure
Li-ion
the chain saw deactivates when the start/stop button
is pressed (green LED off).
To keep the working temperature as low as possible the
machine is equipped with a cooling system.
The cooling system consists of:
1
2
•
Air intake (left side of the machine).
A fan on the motor.
Clean the cooling system with a brush once a week,
more often in demanding conditions. A dirty or
blocked cooling system results in overheating which
causes damage to the machine.
Lubricating the bar tip sprocket
Li-ion
•
Lubricate the bar tip sprocket each time you refill with
saw chain oil. Use the special grease gun and a good
quality bearing grease.
English – 35
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Battery
Li-ion
•
Make sure the battery is not damaged or deformed
and that there are no visible defects such as cracks.
Battery charger
Li-ion
•
Make sure the battery charger and the power supply
cord is not damaged or deformed and that there are
no visable defects such as cracks.
36 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Maintenance schedule
The following is a list of the maintenance steps that must be performed on the machine. Most of the items are described
in the Maintenance section.
Daily maintenance
Weekly maintenance
Monthly maintenance
Check the connections between the
battery and the machine and also
check the connection between battery
and the battery charger.
File off any burrs from the edges of
the bar.
Clean the outside of the machine.
Check that the components of the
power trigger work safely. (Power
trigger lockout and power trigger.)
Empty the oil tank and clean the
inside.
Clean the chain brake and check that
it operates safely. Make sure that the
chain catcher is undamaged, and
replace it if necessary.
Blow through the product and battery
cooling slots gently with compressed
air.
The bar should be turned daily for
more even wear. Check the
lubrication hole in the bar, to be sure it
is not clogged. Clean the bar groove.
If the bar has a sprocket tip, this
should be lubricated.
Check that the bar and chain are
getting sufficient oil.
Check the saw chain with regard to
visible cracks in the rivets and links,
whether the saw chain is stiff or
whether the rivets and links are
abnormally worn. Replace if
necessary.
Sharpen the chain and check its
tension and condition.Check the drive
sprocket for excessive wear and
replace if necessary.
Clean the machines air inlet.
Check that nuts and screws are tight.
Check that the keypad works correctly
and is not damaged.
English – 37
Download from Www.Somanuals.com. All Manuals Search And Download.
MAINTENANCE
Troubleshooting schedule
Keypad
Possible fault codes on the chain saw keypad.
Keypad
Possible faults
Possible action
Pull back the front hand guard to
release the chain brake.
Chain brake engaged.
Temperature deviation
Overload.
Allow the machine to cool down.
The cutting attachment is jammed.
Release the cutting attachment.
Warning indicator flashing.
The power trigger and the
activate button are pressed at
the same time.
Release the power trigger and the
machine is active.
Green activate LED flashing. Low battery voltage.
Charge the battery.
Warning indicator lit.
Service
Contact your service agent.
Battery
Troubleshooting the battery and/or the battery charger during charging.
LED display
Possible faults
Possible action
The battery is discharged.
Charge the battery
Use the battery in surroundings
where temperatures are between
-10 °C and 40 °C.
Temperature deviation
Over voltage
Warning indicator flashing.
Check that the mains voltage
corresponds with that stated on the
rating plate on the machine.
Remove the battery from the
battery charger.
Warning indicator lit.
Cell difference too much (1V) Contact your service agent.
Battery charger
LED display
Possible faults
Possible action
Use the battery charger only when
the surrounding temperature is
between 5 °C and 40 °C.
Warning indicator flashing.
Warning indicator lit.
Temperature deviation
Contact your service agent.
38 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Technical data
T536 LiXP
Engine
Type
BLDC (brushless) 36V
savE
Features
Low energy mode
Lubrication system
Type of oil pump
Oil tank capacity, litre
Weight
Automatic
0,20
Chain saw without battery, bar and chain, empty chain oil tank, kg 2,4
Noise emissions (see note 1)
Sound power level, measured dB (A)
Sound power level, guaranteed LWA dB (A)
Sound levels (see note 2)
104
106
Equivalent sound pressure level at the operator’s ear, dB(A)
Vibration levels (see note 3)
Front handle, m/s2
93
3,3
3,7
Rear handle, m/s2
Equivalent vibration levels (see note 4)
Front handle, m/s2
Rear handle, m/s2
2,0
2,4
Chain/bar
Recommended bar lengths, inch/cm
Usable cutting length, inch/cm
Type of drive sprocket/number of teeth
Maximum chain speed / (savE), m/s
10-14/25-35
9-13/23-33
Spur/6
20 (15)
Approved batteries for T536 LiXP.
Battery
BLi110
BLi150
Type
Lithium-Ion
Lithium-Ion
Battery capacity, Ah
Voltage, V
Weight, kg
3.0
36
4,2
36
1,2
1,3
35
Battery runtime, min, (free run) with SavE activated 35
Approved chargers for the specified batteries, BLi.
Battery charger
Mains Voltage, V
Frequency, Hz
Power,W
QC120
QC330
100-240
50-60
330
220-240
50-60
125
Note 1: Noise emissions in the environment measured as sound power (LWA) in conformity with EC directive 2000/14/
EC.
Note 2: Equivalent sound pressure level, according to ISO 22868, is calculated as the time-weighted energy total for
different sound pressure levels under various working conditions. Typical statistical dispersion for equivalent sound
pressure level is a standard deviation of 1 dB (A).
Note 3:Vibration level, according to EN 60745-2-13. Reported data for vibration level has a typical statistical dispersion
(standard deviation) of 1 m/s2. Declared vibration data from measurements when the machine is fitted with a bar length
and recommended chain type. If the machine is fitted with a different bar length, the vibration level may vary by max
1.5 m/s2.
Note 4: Equivalent vibration level is measured and calculated as for combustion engine powered chainsaws. These
figures are quoted to be able to compare vibration data regardless of type of engine.
English – 39
Download from Www.Somanuals.com. All Manuals Search And Download.
TECHNICAL DATA
Guide bar and saw chain combinations
The following cutting attachments are approved for the model Husqvarna T536 LiXP.
Guide bar
Max. nose
Saw chain
Length, drive
Length, inch
Pitch, inch
Gauge, mm
Type
radius
links (no.)
10
12
14
3/8
3/8
3/8
1,1
1,1
1,1
7T
40
9T
Husqvarna H38 45
52
9T
Saw chain filing and file gauges
EC Declaration of Conformity
(Applies to Europe only)
Husqvarna AB, SE-561 82 Huskvarna, Sweden, tel:+46-36-146500, declares under sole responsibility that the cordless
battery chainsaw HusqvarnaT536 LiXP from 2012’s serial numbers and onwards (the year is clearly stated in plain text
on the type plate with subsequent serial number), are in conformity with the requirements of the COUNCIL’S
DIRECTIVES:
- of May 17, 2006 ”relating to machinery” 2006/42/EC
- of December 15, 2004 ”relating to electromagnetic compatibility” 2004/108/EC.
- of December 12, 2006 ”relating to electrical equipment designed for use within certain voltage limits” 2006/95/EC.
- of September 6, 2006 ”on batteries and accumulators and waste batteries and accumulators” 2006/66/EC.
- of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC.
For information relating to noise emissions, see the Technical data chapter. The following standards have been applied:
EN 60745-1, EN 60745-2-13, EN ISO 11681-2, EN 60335-2-29, EN 62133, EN 55014, EN 55014-2.
Notified body: 0366,VDE-Prüf- und Zertifizierungsinstitut GmbH, Merianstraße 28, DE-63069 Offenbach (Am Main),
Germany, has carried out EC type examination in accordance with the machinery directive’s (2006/42/EC) article 12,
clause 3b.
In addition, SMP, Svensk Maskinprovning AB, Box 7035, SE-750 07 Uppsala, Sweden, has certified conformity with
annex V of the Council’s Directive of May 8, 2000 ”relating to the noise emissions in the environment” 2000/14/EC. The
certificates have the numbers: 01/162/001
The supplied chain saw conforms to the example that underwent EC type examination.
Huskvarna May 23, 2012
Bengt Frögelius, Development manager
(Authorized representative for Husqvarna AB and responsible for technical documentation.)
40 – English
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
1156445-26
´®z+XLT¶6°¨
´®z+XLT¶6°¨
2014-01-08
Download from Www.Somanuals.com. All Manuals Search And Download.
|