853PRO Hydraulic Saw
OPERATOR’S MANUAL
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
853PRO OPERATOR’S MANUAL
TABLE OF CONTENTS
SYMBOLS & LABELS
4
SAFETY
5
7
TECHNICAL SPECIFICATIONS
SET-UP
8
OPERATION
10
12
14
15
MAINTENANCE
TROUBLESHOOTING
REFERENCE
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
3
SYMBOLS & LABELS
853PRO OPERATOR’S MANUAL
THE FOLLOWING SYMBOLS AND DEFINITIONS ARE FOUND THROUGHOUT THIS MANUAL
AND ARE DESIGNED TO MAKE YOU AWARE OF POTENTIAL HAZARDS OR UNSAFE
PRACTICES.
A potentially hazardous situation exists which, if not avoided,
could result in death or serious injury.
WARNING
A potentially hazardous situation exists which, if not avoided,
may result in minor or moderate injury or property damage.
CAUTION
A potential situation exists which, if not avoided, may result in
product or property damage.
IMPORTANT
THE FOLLOWING SYMBOLS & LABELS MAY BE FOUND IN THIS MANUAL OR ON THE SAW
Read the operator’s manual carefully and understand the
contents before you use this equipment.
Always use:
• Protective helmet
• Ear protection
• Protective glasses or full face protection
Wear hand protection
� WARNING
• Inserting the tool into a pre-cut slot that is
• Do not exceed the hydraulic flow
narrower than the chain may cause binding
recommended for your saw model: 8 gpm,
and rapid push-back of the tool toward the
(30 lpm) or 12 gpm (45 lpm) at 2,500 psi
(172.5 bar) hydraulic pressure
• Minimum water pressure 20 psi (1.5 bar)
• Weight 23 lbs (10.4 kg) w/out bar and chain
operator
• Always operate tool with solid footing and
firm hand grip
• Contact at a hydraulic leak or burst can
cause oil injection into the body
READ OPERATIONS & MAINTENANCE MANUAL BEFORE USE OF TOOL.
FAILURE TO OBSERVE THESE PRECAUTIONS CAN RESULT IN SERIOUS
PERSONAL INJURY
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
4
853PRO OPERATOR’S MANUAL
SAFETY
THE FOLLOWING SYMBOL APPLIES TO ALL THE ITEMS LISTED ON THIS PAGE
A potentially hazardous situation exists which, if not avoided,
WARNING
could result in death or serious injury.
Diamond chain breakage can result in high-speed ejection of parts, which can result in death
or serious personal injury to operators or bystanders. The items listed below are critical to
minimizing the risk of diamond chain breakage and injury.
• DO NOT operate a diamond chainsaw with a damaged, modified, broken or missing side
cover, bottom guard or guard flap. The side cover, bottom guard and guard flap provides
protection against contact with moving parts, ejected debris, broken diamond chain,
thrown water and concrete slurry.
• DO NOT operate saw with loose, missing damaged or improperly repaired parts.
• DO NOT exceed the hydraulic flow for your saw model: 8 gpm (30 lpm) or 12 gpm (45 lpm)
at 2,500 psi (172.5 bar) hydraulic pressure.
• DO NOT install or run the chain backwards. The bumper should lead the segment into the
cut.
Bumper
• DO NOT run the saw backwards. The chain should travel away from the operator on the
top of the bar and return on the bottom of the bar.
• DO NOT insert the diamond chainsaw into a slot narrower than the chain segments.
Rapid pushback might occur. Ref: Most diamond segements are .225 (5.72 mm) wide.
• DO NOT use the 853PRO side cover as a replacement cover for another saw.
• DO NOT run the saw upside-down. Concrete debris can fly back into the operator’s face.
• NEVER cut ductile iron pipe with the saw. Segment loss or diamond chain breakage may
occur.
• DO NOT use your hands to search for hydraulic leaks. Hydraulic fluid escaping under
pressure can penetrate skin. If any hydraulic flud is injected into skin seek medical
attention immediately.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
5
SAFETY
853PRO OPERATOR’S MANUAL
THE FOLLOWING SYMBOL APPLIES TO ALL ITEMS LISTED ON THIS PAGE
A potentially hazardous situation exists which, if not avoided,
CAUTION
may result in minor or moderate injury or property damage.
• Always turn the saw OFF when performing maintenance on the saw including diamond
chain tensioning.
• Never use equipment that is not functioning properly. Have the saw repaired by qualified
service personnel.
• Diamond chains require a minimum water pressure of 20 psi (1.5 bar). Insufficient water
supply may result in excessive wear to the diamond chain, which can lead to loss of
strength and diamond chain breakage.
• Never start the saw unless the guide bar, diamond chain and side cover are properly
installed.
GENERAL SAFETY PRECAUTIONS
• Always wear protective clothing, including hard hat, eye protection, hearing protection, and
gloves.
• Avoid loose fitting clothing.
• Perform safety checks before starting each day.
• Always operate tool with solid footing and with both hands on cut-off saw.
• Remove or control slurry to prevent slippery conditions while cutting.
• Be sure there are no obstructions (plumbing, electrical conduit, air ducts) and no unnecessary
people present.
• Set up a well-marked safety zone with a roped boundary and clear signs.
• Provide adequate ventilation when working in an enclosed area. Breathing exhaust gases is
dangerous.
• To avoid electrocution, check for live electrical wiring near cutting area.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
6
853PRO OPERATOR’S MANUAL
TECHNICAL SPECIFICATIONS
853PRO 8 gpm (30 lpm)
23 lbs (10.4 kg)
853PRO 12 gpm (45 lpm)
23 lbs (10.4 kg)
Weight w/out bar and chain
Length
Height
Width
23 inches (58.5 cm)
10.5 inches (26.5 cm)
9.5 inches (24 cm)
23 inches (58.5 cm)
10.5 inches (26.5 cm)
9.5 inches (24 cm)
Hydraulic Supply
8 gpm (30 lpm) @ 2,500 psi (172.5 bar)
Mobil DTE 13M or equivalent
Minimum: 20 psi (1.5 bar)
12 gpm (lpm) @ 2,500 psi (172.5 bar)
Mobil DTE 13M or equivalent
Minimum: 20 psi (1.5 bar)
1 gpm (4 lpm) minimum
Hydraulic Fluid
Requirements (Type)
Water Pressure
Water Flow
Operating Speed
Noise Level
Vibration
1 gpm (4 lpm) minimum
5,700 rpm (avg. free running)
4,800 sfm (avg. free running chain)
5,300 rpm (avg. free running)
4,500 sfm (avg. free running chain)
88 dB @ 3 ft (1 m)
88 dB @ 3 ft (1 m)
4 m/sec² (front handle)
Ref. ISO standard no. 7505
4 m/sec² (front handle)
Ref. ISO standard no. 7505
Torque
130 in-lbs (176 Nm)
11.5 hp (8.6 kW)
207 in-lbs (280 Nm)
17.5 hp (13 kW)
Horsepower
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
7
SET-UP
853PRO OPERATOR’S MANUAL
GUIDE BAR AND DIAMOND CHAIN INSTALLATION
STEP 4
STEP 1
Mount the chain on the bar starting
at the drive sprocket & continue
over the bar nose.
Loosen the side cover nuts and
remove the side cover.
Install the chain correctly. The
bumper must always lead the
segment into the cut as shown here.
STEP 2
Place the bar onto the studs and the
chain adjustment pin.
STEP 3
STEP 5
Turn the chain-tensioning screw
CCW until the bar comes into
contact with the drive sprocket.
Make sure all of the drive links are
inside the bar groove, then pre-
tension the chain.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
8
853PRO OPERATOR’S MANUAL
SET-UP
GUIDE BAR AND DIAMOND CHAIN INSTALLATION
STEP 8
STEP 6
Tension the chain. Do not over
tension the diamond chain. Loss
of power will result. It is normal for
the drivelinks to hang underneath
the guide bar. The diamond chain
should be snug but be able to be
pulled around the guide bar by
hand.
Install the bar clamp plate over the
bar studs.
STEP 7
Install the side cover over the bar
studs and install side cover nuts.
Finger tighten only.
STEP 9
Lift up on the nose of the bar and
firmly tighten the side cover nuts. To
prevent chain tensioner breakage,
be sure the side cover nuts are
tightened to approximately 20 ft-lbs
(27 Nm).
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
9
OPERATION
853PRO OPERATOR’S MANUAL
PRE-CUT CHECKLIST
• Proper Diamond Chain Tension: The diamond chain should be tight but easily pulled around the
guide bar by hand.
• Ensure all safety devices are properly mounted and functional and that all controls are in proper
working order.
• Be sure there are no obstructions (plumbing, electrical conduit, air ducts).
• Always wear protective clothing, including hard hat, eye protection, hearing protection, non-slip
safety boots, gloves, and avoid wearing loose fitting clothing.
• Adequate Water Supply and Pressure
1 gpm (4 lpm) recommended flow
Minimum water pressure 20 psi (1.5 bar)
Note: The single most important factor an operator can control to increase chain life is to
use adequate water pressure. Insufficient water supply will result in excessive wear to the
chain, which can lead to loss of strength and chain breakage.
• Proper Hydraulic Supply to the saw
Maximum Flow 8 gpm (30 lpm) or 12 gpm (45 lpm), depending on saw model
Maximum Hydraulic Pressure 2,500 psi (172.5 bar)
PLANNING THE CUT
• Outline the cut with a permanent marker for a visual cutting guide.
• Avoid pinching the guide bar and diamond chain. Always cut the bottom of an opening first, then
top, and then the sides. Save the easiest cut for last.
• For the straightest cuts use the “Step Cut” method. First score the entire cut line approximately
a 1/2 inch (12 mm) deep using the nose of the guide bar. Next, deepen the cut by about 2 inches
(50 mm). Then plunge all the way through and complete the cut using the WallWalker®.
• Be sure cut concrete cannot fall and injure operator or bystanders. Concrete is very heavy, one
cubic foot = 12 in x 12 in x 12 in = 150 lbs (30 cm x 30 cm x 30 cm = 68 kg).
• Check for live electrical wiring near the cutting area or in the concrete to avoid electrocution.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
10
853PRO OPERATOR’S MANUAL
CUTTING TIPS
OPERATION
• To start a cut, hold trigger on full throttle and slowly plunge the nose of the guide bar straight into
the wall. Use the fixed WallWalker® as a pivot point and pull up on the rear handle to rotate the
guide bar into the cut.
• Always operate the saw at full throttle. Apply enough feed force so that the free running RPM
drops 20 to 30%. If too much force is applied, the saw will lug or stall. The diamond chain will not
have enough speed to cut effectively. If too little feed force is applied, the diamonds will skid and
glaze over.
• For straighter cuts use the “Step Cut” method. First score the entire cut line with the nose of the
guide bar approximately 1/2 inch (12 mm) to 1 inch (25 mm) deep. Next, deepen the cut by about
2 inches (50 mm). This groove will help guide the guide bar for a straight cut. Then plunge all the
way through and complete the cut using the WallWalker®.
• Use the WallWalker® to help cut more efficiently and reduce operator fatigue. The WallWalker®
is a fulcrum that converts inward force to downward force and will develop a 4-to-1 mechanical
advantage. To use correctly, plunge into the wall and simply engage the point of the WallWalker®
into the cut and push straight in. The WallWalker® will force the saw to feed down.
• Apply upward force on the trigger handle to keep the WallWalker® engaged properly, otherwise
the WallWalker® pick will skid, which will reduce the effectiveness. As the saw begins to rotate up,
feed force is developed down the line of the intended cut. Once the saw is fully rotated upwards,
pull the saw out of the cut a few inches and re-engage the WallWalker® to the wall and repeat.
• When cutting rebar, slowly rock the saw so that you’re always cutting concrete as well as steel.
This will help keep the diamonds exposed. Also, expect less diamond chain life when cutting
rebar.
• Expect more diamond chain stretch and guide bar wear when making “nose buried” cuts for
extended periods of time, as the diamond chain does not have a chance to throw the slurry away
from the nose of the guide bar.
• If the saw begins to cut consistently crooked, turn the guide bar over and use the other side.
Dress worn rails with belt sander.
Note: The normal life of a guide bar is two to three diamond chains. Rebar can shorten
guide bar life.
• When using a new diamond chain, you can increase the cutting speed by opening up the
diamonds by making a few cuts in an abrasive material such as a cinder block.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
11
MAINTENANCE
853PRO OPERATOR’S MANUAL
SYSTEM CLEAN-UP
• After cutting, run the saw for at least 15 seconds with the water on to flush slurry and debris from
diamond chain, guide bar and drive sprocket.
• Wash concrete slurry from saw assembly.
• Avoid getting any water in the carburetor or exhaust system. If water enters exhaust port, point
the guide bar tip down and pull the starter handle several times to expel water from muffler.
• Remove guide bar and diamond chain. Flush out the chain tensioner with high water pressure
and lube with grease.
• After cleaning the saw, spray the entire saw body, diamond chain, guide bar, and drive sprocket
with lightweight oil. Using lightweight oil on the saw will minimize rust and help reduce slurry
build up.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
12
853PRO OPERATOR’S MANUAL
MAINTENANCE
DRIVE SPROCKET REMOVAL
• STEP 1 – Prevent the sprocket from rotating by inserting the
scrench or screwdriver through the holes in the sprocket and
the hole in the saw body.
• STEP 2 – Loosen the Trantorque® using a 7/8 in box end
wrench.
NOTE: Slurry will accumulate inside the Trantorque®
adaptor while cutting. This can fill expansion spaces
and make it difficult to remove. To faciliate removal,
turn the hex nut counterclockwise approximately 1/8
turn, and then turn it clockwise slightly, so the hexnut
is loose. Then lightly tap the end of the ring inside the
hex nut several times with your box wrench. (This will
loosen the slurry and allow the components to slide for
removal). Continue to turn the hex nut counterclockwise
to free the sprocket and Trantorque®.
DRIVE SPROCKET INSTALLATION
• STEP 1 – Clean the drive shaft and Trantorque® surfaces
well before installation (Isopropyl alcohol is reccommended,
to remove grease or hydraulic fluid).
Note: Do not lubricate Trantorque® or shaft as slippage
may occur.
• STEP 2 – Slide the Trantorque® shaft adaptor onto drive
shaft until it bottoms on the shaft. Note: Do not lubricate
Trantorque® or shaft as slippage may occur.
• STEP 3 – Slide drive sprocket onto the Trantorque® until it
hits the bottom of the shaft.
• STEP 4 – While holding the sprocket and Trantorque® as
close to the frame of the saw as possible, finger tighten
Trantorque® shaft adaptor.
• STEP 5 – Stop the sprocket from rotating by inserting a
scrench or screwdriver through the holes in the sprocket and
the hole in the saw body.
• STEP 6 – Tighten the Trantorque® shaft adapter with a torque
wrench and a 7/8 in socket to 200 in-lbs (22.6 Nm). When a
torque wrench is not available, use a 7/8 in box end wrench
and tighten one-half turn past finger tight.
Note: Do not turn around or reverse the direction of the
drive sprocket to extend sprocket tooth life. Damage to
chain or drive links may occur.
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
13
TROUBLESHOOTING
TROUBLESHOOTING
853PRO OPERATOR’S MANUAL
• SLOW DIAMOND CHAIN SPEED – Be sure the powerpack is providing the correct hydraulic
pressure and flow depending on your saw model (8 gpm / 30 lpm or 12 gpm / 45 lpm at
2,500 psi / 172.5 bar).
• POOR CUTTING SPEED – The diamonds may be glazed over. Make a few cuts in an abrasive
material such as a cinder block to expose the diamonds.
• PREMATURE CHAIN STRETCH – Not enough water pressure. The minimum water pressure
is 20 psi (1.5 bar). Insufficient water supply will result in excessive wear on the chain, which can
lead to loss of strength and chain breakage.
• CHAIN TENSIONER BREAKAGE – Side cover nuts are not tight enough.
Torque to 20 ft-lbs (27 Nm).
• WATER NOT FLOWING – Water hose is kinked or supply is not turned on.
• MOTOR WON'T TURN – Hydraulics are hooked up backwards or powerpack is set on reverse
flow.
Further questions?
Call 800.321.1240
or
visit our website at:
icsbestway.com
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
14
853PRO OPERATOR’S MANUAL
APPROXIMATE CUTTING RATES
REFERENCE
Material
Cutting Rate
Concrete – 6 in (15 cm)
Red Brick – 6 in (15 cm)
Rebar – #4 (12 mm)
5 lineal in/min (12 cm/min)
10 lineal in/min (25 cm/min)
10–20 seconds through each piece
INCH-FOOT DEFINITION
An in-ft is a measure of how much material is to be cut.
An in-ft is defined as: depth in inches times length in feet.
Note: 129 in-ft = 1 m2
Example: How many in-ft are in this doorway?
1. Determine the depth of the cut in inches.
For this example, 8 inches.
2. Determine the length of the cut in feet.
3+7+3+7=20 feet
3. Multiply the two numbers
8 in x 20 ft = 160 in-ft
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
15
REFERENCE
853PRO OPERATOR’S MANUAL
PERFORMANCE LOSS VS. HYDRAULIC HOSE LENGTH
ASSUMPTIONS:
• 8 gpm (30 lpm) or 12 gpm (45 l/min) flow at 2,500 psi (172.5 bar)
• Zero elevation change
• 2 pairs of flush-face fittings per hose
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
16
853PRO OPERATOR'S MANUAL
ICS, Blount Inc.
4909 SE International Way
Portland, OR 97222
Tel 800.321.1240 Fax 503.653.4393
icsbestway.com
© 2008 ICS, Blount International Inc. Specifications are subject to change without notice. REV0708 F/N 71904
|