MODEL T23107
CHAIN SAW SHARPENER
OWNER'S MANuAL
Download from Www.Somanuals.com. All Manuals Search And Download.
This manual provides critical safety instructions on the proper setup,
operation, maintenance, and service of this machine/tool. Save this
document, refer to it often, and use it to instruct other operators.
Failure to read, understand and follow the instructions in this manual
may result in fire or serious personal injury—including amputation,
electrocution, or death.
The owner of this machine/tool is solely responsible for its safe use.
This responsibility includes but is not limited to proper installation in
a safe environment, personnel training and usage authorization,
proper inspection and maintenance, manual availability and compre-
hension, application of safety devices, cutting/sanding/grinding tool
integrity, and the usage of personal protective equipment.
The manufacturer will not be held liable for injury or property damage
from negligence, improper training, machine modifications or misuse.
Some dust created by power sanding, sawing, grinding, drilling, and
other construction activities contains chemicals known to the State
of California to cause cancer, birth defects or other reproductive
harm. Some examples of these chemicals are:
• Lead from lead-based paints.
• Crystalline silica from bricks, cement and other masonry products.
• Arsenic and chromium from chemically-treated lumber.
Your risk from these exposures varies, depending on how often you
do this type of work. To reduce your exposure to these chemicals:
Work in a well ventilated area, and work with approved safety equip-
ment, such as those dust masks that are specially designed to filter
out microscopic particles.
Download from Www.Somanuals.com. All Manuals Search And Download.
Specifications
Motor
Rpm’s
120V,60Hz
4200
Vise Capacity
Table/Vise Angles
Arbor Diameter
0.80"to 0.50"
35 Degrees Right to Left
7/8"
Wheel Dimensions
Overall Dimensions
Weight
4-1/4"Dia. X 1/8" Thick
9"W x 10"L x 12-1/8"H
4.85Lbs
Save This manual
You will need the manual for the safety warnings and precautions, assembly instructions,
operating and maintenance procedures, parts list and diagram. Keep the manual in a safe and
dry place for future reference.
Safety Warnings and Precautions
WARNING: When using tools, basic safety precautions should always be followed to
reduce the risk of personal injury and damage to equipment.
Read all instructions before using this tool !
Keep work area clean luttered areas invite injuries.
1,
. C
2.Observe work area conditions. Do not use machines or power tools in damp or wet locations. Don’t
expose to rain. Keep work area well lighted. Do not use electrically powered tools in the presence of
flammable gasses or liquids.
3.Keep children away. Children must never be allowed in the work area, Do not let them handle machines,
tools, or extension cords.
4.Store idle equipment. When not in use, tools must be stored in a dry location to inhibit rust. Always lock up
tools and keep out of reach of children.
5.Use the right tool for the job. Do not attempt to force a small tool or attachment to do the work of a larger
industrial tool. There are certain applications for which this tool was designed. It will do the job better and more
safely at the rate for which it was intended. Do not modify this tool and do not use this tool for a purpose for
which it was not intended.
6.Dress properly. Do not wear loose clothing or jewelry as they can be caught in moving parts.
Protective, electrically non-conductive clothes and no-skid footwear are recommended when working. Wear
restrictive hair covering to contain long hair
7.Use eye and ear protection. Always wear ANSI approved impact safety goggles. Wear a full face shield if
you are producing metal filings or wood chips.
8.Do not overreach. Keep proper footing and balance at all times. Do not reach over or across running
machines.
Page 2
Download from Www.Somanuals.com. All Manuals Search And Download.
9.Maintain tools with care. Keep tools sharp and clean for better and safer performance. Follow instructions
for lubricating and changing accessories. Inspect tool cords periodically and if damaged, have them repaired
by an authorized technician. The handles must be kept clean, dry, and free from oil and grease at all times.
10. Avoid unintentional starting. Be sure the switch is in the Off position when not in use and before
plugging in.
11.Stay alert. Watch what you are doing, use common sense. Do not operate any tool when you are tired.
12.Check for damaged parts. Before using any tool, any part that appears damaged should be carefully
checked to determine that it will operate properly and perform its intended function. Check for alignment and
blinding of moving parts; any broken parts or mounting fixtures; and any other condition that may affect proper
operation. Any part that is damaged should be properly repaired or replaced by a qualified technician. Do not
use the tool if any switch does not turn On and Off properly.
13.Guard against electric shock. Prevent body contact with grounded surfaces such as pipes, radiators,
ranges, and refrigerator enclosures.
14.Replacement parts and accessories. When servicing, use only identical replacement parts. Use of any
other parts will void the warranty. Only use accessories intended for use with tool.
15.Do not operate tool if under the influence of alcohol or drugs. Read warning labels on prescriptions to
determine if your judgment or reflexes are impaired while taking drugs. If there is any doubt, do not operate the
tool.
16.Use proper size and type extension cord. If an extension cord is required, it must be of the proper size
and type to supply the correct current to the tool without heating up. Otherwise, the extension cord could melt
and catch fire, or cause electrical damage to the tool. This tool requires use of an extension cord of 0 to 10
amps capability ( up to 50 feet ),with wire size rated at 18 AWG. Longer extension cords require larger size
wire. If you are using the tool outdoors, use an extension cord rated for outdoor use.
17.Maintenance. For your safety, maintenance should be performed regularly by a qualified technician.
18. Never use the Electric Chainsaw Sharpener around flammable materials.
19.This product contains lead, which is a chemical known to the State of California to cause cancer and birth
defects or other reproductive harm. (California Health & Safety Code 25249.2, et seq.)
Note: Performance of this tool (if powered by line voltage ) may vary depending on variations in local
line voltage. Extension cord usage may also affect tool performance.
Warning: The warnings, cautions, and instructions discussed in this instruction discussed in this
instruction manual cannot cover all possible conditions and situations that may occur. It must be
understood by the operator that common sense and caution are factors which cannot be built into this
product, but must be supplied by the operUnpacking.
Page 3
Download from Www.Somanuals.com. All Manuals Search And Download.
Additional Safety Warnings
Grinding Wheel Warnings
1.Do not use a grinding wheel if it is chipped, cracked, or worn. You can check if the wheel has cracks not
visible to the human eye by hanging it up by the central hole and tapping it with a non-metal object (ie:
screwdriver handle). If it is in good condition it will produce a metallic sound. A dull sound indicates a crack or
break.
2.Only use grinding wheels that fit the arbor (7/8"). Do not try to change or modify the mounting hole on a
grinding wheel to make it fit.
3.Do not over-tighten the grinder lock cap (#9). Hand tighten it only. Overtightening may cause the wheel to
break or disintegrate.
4.Never use the chain saw sharpener without the grinding wheel cover (#11) in place.
5.Always test the grinding wheel ( #8) by running it for a minute prior to contact with a chain.
6.Keep away from the wheel when it is turning, and make sure no one is standing close, in the line of the
wheel rotation trajectory.
7.If the grinding wheel vibrates, turn off the machine immediately and check that it is mounted securely, and
that is not damaged.
8.Never try to stop the grinding wheel with your hands, even if you are wearing safety gloves. The wheel will
cut through gloves and your hand, causing serious injury.
9.Never operate tool without the Grinding Wheel Cover in place.
10.Replacement grinding wheel listed speed must meet or exceed RPM rating of the tool.
Warning!!: This machine is designed to sharpen chain saw chains. Do not attempt to sharpen any other tools
and do not attempt to grind any other objects.
Unpacking
When unpacking, check to make sure the parts listed on page 9 are included.
Assembly
1.When installing the sharpener on a workbench, make sure that the lock wheel (#18) (is accessible as shown
in the mounting picture in FIGURE 1.
2.Bolt (bolts not included ) the unit directly to the workbench through the two 1/4" holes on the base (#17). The
workbench mush have a solid surface capable of supporting the weight of this product, the work-piece and
assorted tools. See FIGURE 2.
Download from Www.Somanuals.com. All Manuals Search And Download.
Page 4
Always unplug the unit before changing grinding wheels, or when making any adjustments to the
Warning !
sharpener.
Mounting a Grinding Wheel
Refer to the assembly drawing on page 10 and FIGURE 3 and FIGURE 4 below.
Raise the Top Housing (#4) and lock it in the up position by tightening the Lock Stop (# 6)
Remove the two screws holding the Grinding Wheel Cover (#11), Set the cover aside.
Unscrew the Grinder Lock Cap (#9) that holds the Grinding Wheel ( #8) in place.
Install the new wheel on the Grinding Wheel Base (#7),making sure it fits properly.
1.
2.
3.
4.
Note : Do not use a grinding wheel if it chipped, cracked, or worn. You can check if the wheel has cracks not
visible to the human eye by hanging it up by the central hole and tapping it with a non metal object (ie:
screwdriver handle). If it is in good condition it will produce a metallic sound. A dull sound indicates a crack or
break.
Replace the Grinder lock Cap (#9).
5.
6.
7.
Replace the Grinding Wheel Cover (#11).
Release the Lock Stop (#6) and lower the Top Housing (#4).
8. Never operate tool without the Grinding Wheel Cover in place.
Download from Www.Somanuals.com. All Manuals Search And Download.
Operation
Warning ! Always unplug the unit while adjusting chain to be sharpened.
Refer to the assembly drawing on page 10 and the various photographs.
Note: Raise the Top Housing (#4) while adjusting the chain.
1.Clean the chain before sharpening . Wash it with o non-flammable solvent. Don’t not use Gasoline. Dry the
chain.
Page 5
Operation (continued)
2.Lift up the Chain Stop(#23) and secure the chain in the sliding Guides (#31). See FIGURE 6.
3.Lower the Chain Stop(#23) so that it is positioned on the tooth (cutter)you want to start with. See FIGURE 5.
Download from Www.Somanuals.com. All Manuals Search And Download.
4.See FIGURES 5&6. Loosen the LOCK Wheel (#18) to allow entire housing to turn. Rotate the housing to
match the degree of angle you need on the Angle Gauge. Chains come in various sizes with varying degrees
of sharpening angles. Check with your chain manufacturer’s manual to determine what degree you need to
sharpen at. Once the degree is set, tighten the Lock Wheel(#18).
5.Lower the Top Housing(#4) so that the Grinding Wheel(#8) skims the chain tooth.
6.Hold it at that position while you
Tighten the Lock Stop(#6)so that the
Wheel will only go down to that point
See FIGURE7.
7.Depending on the amount of material
you wish to remove, tighten or loosen
the Lower Knob(#26) and set the Lock
Nut. Wee FIGURE5.The Lower
Konb (26) has a Lock Nut which will determine how
much materail is removed. Once you set the Lock
Nut, fully tighten the Lower Knob(26).
the Lower Knob(26).
Page 6
Operation (continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
8.Lock the chain in the Sliding Guides
(#31)by turning the Handle(#34).
See FIGURE 8.The Handle(#34) should
be situated so that you can easily release
and tighten it . You will need to release it
each time you move to the next link, and
tighten it to sharpen each link.
9.If the chain has been repeatedly
sharpened, the chain depth limiting
gauges may need to be taken down
with a flat file(not included).
See FIGURES 8&9 .File down
each gauge so that they are at
a lower level than cutting teeth.
Sharpening.
1.Put on your protective gear and make sure the immediate area is clear of bystanders.
2.Plug in the Power Cord(#3) and push the green button on the Switch Plate(#5)to turn on the machine.
3.Slowly lower the grinding wheel as shown
in FIGURE10. If you notice slight errors in your
settings, turn off the unit and unplug it before
you make your adjustments.
Note: A good grind occurs when the contact
between the wheel and the teeth are gradual and
smooth. Do not stop too long time on each tooth.
4.After sharpening one tooth, turn off the machine.
Lift
the
Top
Housing(#4),release
the
Handle(#34),and move the chain so that the next
link is positioned in the Chain Stop(#23). Tighten
the Handle(#23).Turn the machine back on and
continue sharpening the next tooth. Repeat this
process until you have sharpened all of the links set
up for this angle.
Page 7
Operation(continued)
Download from Www.Somanuals.com. All Manuals Search And Download.
5.After you fininshed sharpening all of the teeth set for your
current angle, turn off the machine by pushing the red button on
the Switch Plate(#5) and unplug the unit.
6.Loosen the Lock Wheel(#18)and reset the angle so that the
first tooth that hasn’t been sharpened is positioned against the
Chain Stop (#23) and locked in as explained on page 6. See
FIGURE 11.
7.As you did with the first half of the chain, be sure to lower the
Top Housing(#4) so that the Grinding Wheel (#8) skims the
chain tooth, and lock it in place. See page6. Follow all of the
steps on page 6 double checking everything before you plug in
the machine and turn it on again.
Remember to turn off the machine and unplug it if you need to make any adjustments.
8.After you repeat all of the steps under sharpening on page7, your chain is ready to be mounted on your
saw.
Maintenance
1.Keep the Sharpener clean and free of dust, metal debris and dirt.
2.Check the grinding wheel before each use to make sure it isn’t damaged. Do not use a grinding wheel if it is
chipped, cracked, or worn. You can check if the wheel has cracks not visible to the human eye by hanging it
up by the central hole and tapping it with a non metal object (ie: screwdriver handle). If it is in good condition it
will produce a metallic sound. A dull sound indicates a crack or break.
3.Replace the grinding wheel when it grinds down to a diameter of 3 inches.
Page 8
Download from Www.Somanuals.com. All Manuals Search And Download.
Parts List
Parts No.
Description
Screw
Qty.
3
Parts No.
Description
Washer
Qty
1
1
2
20*
21*
Motor Cover
1
Bearing
1
3
4
5
6
7
Power Cord
Top Housing
Switch Plate
Lock Stop
Grinding Wheel Base
1
1
1
1
1
22*
23*
24*
25*
26*
Swing Arm
Chain Stop
Tension Spring
Retaining Ring
Lower Knob
1
1
1
1
1
8
9
10
Grinding Wheel
Grinder Lock Cap
Screw
1
1
2
27*
28*
29*
Screw
Bolt
Chain Saw Frame
1
1
1
11
12
Grinding Wheel Cover
O-Seal Ring
1
2
30*
31*
Square Neck Screw
Sliding Guide
2
2
13
14
15
16
17
18
19*
Punching Axis
Torsion Spring
Switch Circuit Board
Nut
Base
Lock Wheel
Screw
1
1
1
1
1
1
1
32*
33*
34*
35*
36*
37
Pad
Screw
Handle
Spring
Lock Screw
Retaining Ring(10)
Motor
2
1
1
1
1
2
1
38
The Chain Mounting Assembly ( #39) is only available as a set. It includes all part
numbers with asterisks(*). Part numbers with asterisks ( 19 through 36)a re not available
individually.
PLEASE READ THE FOLLOWING CAREFULLY
THE MANUFACTURE AND/OR DISTRIIBUTOR HAS PROVIDED THE PARTS DIAGRAM IN THIS
MANUAL AS A REFERENCE TOOL ONLY. NEITHER THE MANUFACTURER NOR DISTRIBUTOR
MAKES ANY REPRESENTATION OR WARRANTY OF ANY KIND TO THE BUYER THAT HE OR SHE
IS QUALIFIED TO MAKE ANY REPAIRS TO THE PRODUCT OR THAT HE OR SHE IS QUALIFIED TO
REPLACE ANY PARTS OF THE PRODUCT. IN FACT, THE MANUFACTURER AND/OR DISTRIBUTOR
EXPRESSLY STATES THAT ALL REPAIRS AND PARTS REPLACEMENTS SHOULD BE
UNDERTAKEN BY CERTIFIED AND LICENSED TECHNICIANS AND NOT BY THE BUYER.THE
BUYER ASSUMES ALL RISK AND LIABILITY ARISING OUT OF HIS OR HER REPAIRS TO THE
ORIGINAL PRODUCT OR REPLACEMENT PARTS THERETO.OR ARISING OUT OF HIS OR HER
INSTALLATION OF REPLACEMENT PARTS THERETO
NOTE: Some parts are listed and shown for illustration purposes only and are not available individually as
replacement parts.
Page 9
Download from Www.Somanuals.com. All Manuals Search And Download.
Download from Www.Somanuals.com. All Manuals Search And Download.
WARRANTY AND RETURNS
Grizzly Industrial, Inc. warrants every product it sells for a period of 1 year to the original purchaser from
the date of purchase. This warranty does not apply to defects due directly or indirectly to misuse, abuse,
negligence, accidents, repairs or alterations or lack of maintenance. This is Grizzly’s sole written warranty
and any and all warranties that may be implied by law, including any merchantability or fitness, for any par-
ticular purpose, are hereby limited to the duration of this written warranty. We do not warrant or represent
that the merchandise complies with the provisions of any law or acts unless the manufacturer so warrants.
In no event shall Grizzly’s liability under this warranty exceed the purchase price paid for the product and
any legal actions brought against Grizzly shall be tried in the State of Washington, County of Whatcom.
We shall in no event be liable for death, injuries to persons or property or for incidental, contingent, special,
or consequential damages arising from the use of our products.
To take advantage of this warranty, contact us by mail or phone and give us all the details. We will then
issue you a “Return Number,’’ which must be clearly posted on the outside as well as the inside of the
carton. We will not accept any item back without this number. Proof of purchase must accompany the
merchandise.
The manufacturers reserve the right to change specifications at any time because they constantly strive to
achieve better quality equipment. We make every effort to ensure that our products meet high quality and
durability standards and we hope you never need to use this warranty.
Please feel free to write or call us if you have any questions about the machine or the manual.
Thank you again for your business and continued support. We hope to serve you again soon.
Download from Www.Somanuals.com. All Manuals Search And Download.
Buy Direct and Save with Grizzly® – Trusted, Proven and a Great Value!
~Since 1983~
ORDER
24 HOURS A DAY!
1-800-523-4777
Download from Www.Somanuals.com. All Manuals Search And Download.
|