Instruction Manual
Model F100-4
PICTURE FRAMING
SAW FENCE
KIT
Description
The Saw Fence Kit Model F100-4 is an
upgrade feature for the Studio Saw Model
F100-1. The kit includes a measuring scale
( 36” to the left and 18” to the right) to
make measuring and cutting moulding
faster, easier and more accurate. Also
included is an additional clamp and a
production stop. The addition of this kit
completes the framing saw system.
Producing professional quality picture
frames is now easier than ever.
Download from Www.Somanuals.com. All Manuals Search And Download.
Model F100-4
Instruction Manual
SAW FENCE KIT
Identification
Rabbet
Section
18” Right Fence
and Scale
Stop
36” Left Fence
and Scale
Leg
Stop - Allows moulding to be cut in identical lengths.
Rabbet - Under cut of moulding which holds frame
material.
Fence and Scale - 36” left section and 18” right
section. Scale is specially designed for measuring 45˚
picture frame mitres.
Leg - Support for 36” fence.
1
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Model F100-4
Instruction Manual
SAW FENCE KIT
Parts List
18” Fence
Extension
18” Right
Hand
Fence
Leg
Leg Screw
18” Left Hand
Fence
Wrench
Stop
Fence
Connectors
Parts List
18” Fence Extension
18” Left Hand Fence
1
1
18” Right Hand Fence 1
Fence Connectors
Fence Screw
Leg
2
4
1
1
1
1
Leg Screw
Stop
Wrench
2
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Model F100-4
Instruction Manual
SAW FENCE KIT
Assembly Procedure
1. Remove clamp and rod (Fig.1).
a. Unscrew nut and bolt. Keep spacer.
Discard nut and bolt.
2. Remove base board (Fig.2).
a. Remove four base screws.
3. Fence
Fig. 1
a. Attach fence extension to left hand fence.
Feed sections together thru connector
plates (Fig 3).
b. Tighten set screws.
c. Attach leg to fence (Fig. 4).
d. Peel scale backing paper and carefully lay
scale flat onto fence. Start at intersection
and slowly lay scale down toward end of
fence (Fig. 5).
Fig. 2
Fig. 3
e. Align fence sections onto saw base. Install
screws thru back of saw base into fence
(Fig. 7).
f. Install screws thru bottom of saw base
(Fig. 6).
Fig. 6
Fig. 4
Fig. 5
Fig. 7
3
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
SAW FENCE KIT
Model F100-4
Instruction Manual
Assembly Procedure (continued)
4. Base
a. Turn saw base over and install base board.
Be sure holes for rods are located toward
back of saw base (Fig. 8).
5. Clamp rods
a. With rounded ends facing up set rod into
hole in base board.
Fig. 8
b. Align hole in rod with hole in back of saw
base.
c. Install screw thru rod, thru rod spacer and
Spacer
into saw base. (Fig. 9).
d. Slide clamp onto rod (Fig. 10).
6. Stop
a. Slide moulding stop onto fence (Fig. 11).
b. Tighten screw to lock.
7. Secure Base
Fig. 9
✔
✔
a. Bolt base to work surface to eliminate
slipping and make cutting easier.
Use 1/4” (6mm) drill for pilot hole.
Fig. 10
b. Use two 4” deep throat C-clamps.
Available at local hardware store.
Fig. 11
4
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Model F100-4
Instruction Manual
SAW FENCE KIT
Operation
A. First Cut
1. Set pivot to 45˚ on right (Fig. 12).
2. Place moulding against fence finished side up and
rabbet facing operator.
Fig. 12
3. Slide moulding under saw blade far enough so full
45˚ cut can be made.
Fig. 13
4. Adjust clamp foot onto moulding and tighten knob
(Fig. 13).
5. Cut moulding (Fig. 14).
• By making long full strokes accuracy is improved
and cutting is easier.
✔
✔
• Always cut long pieces first. If mistake is made,
shorter pieces can be salvaged.
6. Deburr bottom cut edge using sandpaper, sander
or file.
A. Second Cut
1. Set pivot to 45˚ on left (Fig. 15).
Fig. 14
2. Slide cut end of moulding to desired dimension and
align rabbet corner on scale dimension (Fig. 16).
3. Set stop against moulding.
4. Clamp both sides of moulding if possible.
5. Cut moulding.
Fig. 15
Fig. 16
5
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Model F100-4
Instruction Manual
SAW FENCE KIT
Trouble Shooting
Problem
Solution
Scale did not lay in correct position.
As long as the scale has not been pressed/rubbed into position
thereby “fixing” the adhesive it should be possible to carefully
remove/lift scale off the fence and re-position.
Moulding lengths are not consistent.
Make sure fence is secure.
Clamp left hand side of moulding first when using the stop.
Remove any saw dust, splinters and debris from between the
moulding and fence and the moulding and the stop.
Clamp does not hold moulding firmly.
Difficult or slow cutting.
Turn clamps 90 degrees so that they press the moulding into the base
and back of fence.
Make sure the clamp posts are tight.
Make sure the saw blade is correctly installed (teeth facing away
from saw handle).
Replace saw blade.
Saw does not cut straight.
Increase blade tension using knurled nut under handle.
Tighten both swivel screws on back of saw base equally.
Make sure moulding is securely clamped.
Tighten down on the angle block pointer, be sure you can still move
the saw from left hand 45˚ to the right hand 45˚ marks.
Warranty
Logan Graphic Products, Inc. (“Logan”) warrants the Studio Fence Kit - Model F100-4, to be free from defects in parts
and workmanship for a period of one year from the date of original purchase. Logan warrants that it will either repair or
replace, at it’s sole discretion, any necessary replacement parts found to be defective. Should the product need to be
returned to Logan for repair or replacement parts, authorization for any return must come from Logan in writing. Costs
of returning the product to Logan, including insurances, shall be borne by the purchaser. Logan shall not be liable for
any damages or losses, incidental or consequential, direct or indirect, arising from the use of this product. This war-
ranty extends only to the original purchaser and is not assignable or transferable. This warranty is in lieu of all other
warranties, expressed or implied.
6
Logan Graphic Products Inc., 1100 Brown Street, Wauconda, IL 60084 Toll Free 1 800 331 6232 www.logangraphic.com
Download from Www.Somanuals.com. All Manuals Search And Download.
Logan Graphic Products Inc.,
1100 Brown Street, Wauconda, IL 60084
Toll Free 1 800 331 6232
Reference Part No. L567-N
Download from Www.Somanuals.com. All Manuals Search And Download.
|